Search results for "Titanium"
showing 10 items of 878 documents
Analysis of powdered tungsten carbide hard-metal precursors and cemented compact tungsten carbides using laser-induced breakdown spectroscopy
2007
Laser-induced breakdown spectroscopy (LIBS) has been applied to the direct analysis of powdered tungsten carbide hard-metal precursors and cemented tungsten carbides. The aim of this work was to examine the possibility of quantitative determination of the niobium, titanium, tantalum and cobalt. The investigated samples were in the form of pellets, pressed with and without binder (powdered silver) and in the form of cemented tungsten carbides. Several lasers and detection systems were utilized.
Microstructure and property of titanium heterogeneous laser welding
2015
International audience; Dissimilar welding has been investigated for three different couples of titanium alloys: α/α+β, α/β and α+ββp. Plates of 100 x 60 x 1.6 or 1.8 mm were welded with a Yb: YAG laser. Tensile tests show that the properties of the dissimilar welded specimens were generally controlled by Those of the weakest material except for the α+β/β where the ultimate tensile strength was approximately equal to the average value of both materials. In every case, the welding sample elongation was found to be smaller than that of the base metals. The rupture took place away from the bead and was found to be always located in the alloy having the lowest mechanical properties. Nevertheles…
Dissimilar laser welding of AISI 316L stainless steel to Ti6–Al4–6V alloy via pure vanadium interlayer
2015
Abstract Successful continuous laser joining of AISI 316L stainless steel with Ti6Al4V titanium alloy through pure vanadium interlayer has been performed. Three welding configurations were tested: one-pass welding involving all three materials and two pass and double spot welding involving creation of two melted zones separated by remaining solid vanadium. For the most relevant welds, the investigation of microstructure, phase content and mechanical properties has been carried out. In case of formation of a single melted zone, the insertion of steel elements into V-based solid solution embrittles the weld. In case of creation of two separated melted zones, the mechanical resistance of the j…
Titanium complexes for the formation of nitrogen compounds : synthesis of homoallylamines and amidines
2011
Homoallylic amines are key reagents for the formation of a large number of biologically interesting products. Due to the double bond of their allylic moiety, easily functionalisable, they are commonly used in organic synthesis. This research work deals with the synthesis of homoallylic amines thanks to titanium complexes. In fact, the reductive coupling between of imines and dienes promoted by titanium allows the formation of diastereoisomeric homoallylamines syn and anti. The diastereoselectivity of the reaction is directly affected by the nitrogen substituent. Whether it is benzyl or phenyl, the selectivity will be in favour of syn or anti respectively. Moreover, the addition of a the Lew…
Bactericidal Effect of the Er:YAG Laser on Dental Implant Surfaces: An In Vitro Study
2002
The aim of the in vitro study was to examine the bactericidal effect of an Er:YAG laser on common dental implant surfaces.Seventy-two titanium platelets with 3 different surfaces--sandblasted and acid-etched (SA), titanium plasma-sprayed (TPS), and hydroxyapatite-coated (HA)--were incubated with a suspension of Streptococcus sanguinis (ATCC 10556). Irradiation at pulse energies of 60 and 120 mJ and a frequency of 10 pps was performed on a computer-controlled XY translation stage. After laser treatment the specimens were sonicated and the bacterial growth examined by counting colony forming units on blood agar plates. Temperature elevations during irradiation were investigated using K-type t…
Au/TiO2-CeO2 Catalysts for Photocatalytic Water Splitting and VOCs Oxidation Reactions
2016
Photocatalytic water splitting for H2 production and photocatalytic oxidation of 2-propanol, an example of volatile organic compounds, were investigated over TiO2 catalysts loaded with gold and/or ceria. In the water splitting reaction the presence of gold only slightly affected the performance of TiO2 whereas the presence of CeO2 had a more remarkable positive effect. In the 2-propanol oxidation Au/TiO2 was the most active sample in terms of alcohol conversion whereas Au/TiO2-CeO2 exhibited the highest CO2 yield. On the basis of characterization experiments (X-Ray Diffraction (XRD), Energy Dispersive X-ray Analysis EDX, surface area measurements, Diffuse Reflectance Spectroscopy (DRS) and …
Preparation in mild conditions of photocatalytically active nanostructured TiO2 rutile
2006
Abstract Nano structured TiO 2 rutile samples were prepared in mild conditions by hydrolysis of TiCl 4 in different solutions. The powders revealed a fair photoactivity for the photoeatalytic degradation of 4-nitrophenol. The influence of preparation procedure, pH and presence of Cl − and N 3 − anions on the physicochemical features and photocatalytic activity of the powders was investigated.
ChemInform Abstract: Enhanced Surface Area in Thermally Stable Pure Mesoporous TiO2.
2001
Abstract We describe here for the first time the surfactant-assisted synthesis of thermally stable mesoporous pure TiO 2 having a high surface area. Our synthetic approach to the chemistry of this system is based on the equilibrium between the hydrolysis and condensation reactions of the inorganic species and the organic–inorganic self-assembling processes. The use of titanatrane complexes helps to retard the hydrolysis and condensation reactions, thus allowing us to overcome the difficulties in preparing titanium dioxide mesoporous materials starting from highly reactive Ti-alkoxides. The mesoporous material has been characterized by TEM, XRD and N 2 adsorption–desorption isotherms and dis…
Defect detection in additively manufactured titanium prosthesis by flying laser scanning thermography
2018
Abstract Metal additive manufacturing is nowadays a well-established technology for cutting edge applications in the automotive, aerospace, defense and medical sectors. Since additive metal deposition is basically a welding method, which creates parts by successively adding layers of material, there is a chance for defects like pores, cracks, inclusions and lack of fusion to develop. As a matter of fact, interlayer and intralayer defects are often observed in additive manufactured components. However, if one considers the typical end applications along with the high costs involved in metal additive manufactured components, a “zero defect” target is close to mandatory for this technology. Pl…
Vertical Osteoconductive Characteristics of Titanium Implants with Calcium-Phosphate-Coated Surfaces - A Pilot Study in Rabbits
2014
Introduction: Osteoconductive characteristics of different implant surface coatings are in the focus of current interest. The aim of the present study was to compare the vertical osteoconductivity at the implant shoulder of supracrestal inserted calcium-phosphate coated implants (SLA-CaP) with conventional sand-blasted/acid-etched (SLA) implants in a rabbit model. Materials and Methods: SLA-CaP and SLA implants were inserted bilaterally in the mandible of four rabbits in a split-mouth design. The implants were placed 2 mm supracrestal. After 3 weeks, at the left and right implant shoulder, the percentage of linear bone fill (PLF) as well as bone-implant contact (BIC-D) were determined. Resu…