Search results for "Tito"
showing 10 items of 719 documents
Automatic detection of thermal anomalies in induction motors
2021
The paper proposes a methodology based on Artificial Intelligence techniques for the automatic detection of abnormal thermal distributions in electric motors, to rapidly identify pre-faults or fault conditions. The proposed approach, applied to induction motors of different sizes, installed in waterworks plants, is based on the execution of Thermographic Non-Destructive Tests, which allow identifying abnormal operating conditions without interrupting the ordinary working conditions of the system. Thermographic images of induction motors are acquired at the installation site and with perspectives visible to the operator, which are sometimes partially obstructed. These thermographic images ar…
PV Reconfiguration Systems: a Technical and Economic Study
2017
Dynamical electrical array reconfiguration strategies for grid-connected PV systems have been proposed as solution to improve energy production due to the mismatch effect of PV plants during partial shading conditions. Strategies are based on the use of dynamic connections between PV panels given by the employment of switches that allow for each panel the series, parallel or exclusion connections, physically changing the electrical connections between the related PV modules, consequentially modifying the layout of the plant. Usually the cost of the dynamic matrix is not taken into account. This novel work evaluates the economic advantages obtained by the use of reconfiguration strategies in…
Evaluation of performance and efficiency and type approval of an electrically assisted bicycle drive
2013
The diffusion of electrically assisted bicycles gives rise to the need of the evaluation of the performance and efficiency of the electric drive that supply it. In this paper, is presented a test bench for the estimation of the electric drive output torque under several speed and load conditions. Moreover, the test bench detects the electrical and mechanical parameters that allow to evaluate the electrical drive efficiencies. The test bench has been designed in agreement with the Directive 2002/24/EC of the European Parliament since it detects the maximum continuous rated power (that must be lower than 0.25 kW) and evaluates if the output is progressively reduced and finally cut off as the …
Hydrogen from The Sea: The Challenge of the Future. Present and Future Developments
2014
In this paper we proposed the use of saline water to product hydrogen. As far as using saline water, can be proposed two different scheme and technology. The aim of this work is to design an electrolyze system capable of utilizing sea water for direct electrolysis. It is probable that these systems would operate at a low power density and electrolyze only a small portion of the water in contact with electrodes. In particular, we present the results obtained by two different prototype of electrolyzer: one with steel electrodes and the second electrodes with titanium. Further experiments were carried out by changing the electrolytic solution of water and sodium chloride in real seawater. Fina…
Modelling, simulation and characterization of a supercapacitor
2020
In the last decade, the issue of air pollution or the reduction of CO2 emissions has become of extreme interest both for civil society and then for the industrial and scientific research world. For this reason, the scientific research on automotive is called to answer with increasingly innovative solutions. One of the principal subjects are the storage and the utilization of the electric energy for electrical and hybrid vehicles. Nowadays, supercapacitors are getting more and more attention because of their characteristics that allow them to be a bridge between electrolytic capacitors and batteries in several application such as bust-mode energy delivery, regenerative breaks and so on. The …
Sensorless variable speed single-phase induction motor drive system based on direct rotor flux orientation
2012
The single-phase induction motor (SPIM) is one of the electrical machines more used in the World, and can be found in several fractional and sub-fractional horsepower applications in houses, offices, shoppings, farms, and industries. The introduction of more sophisticated applications has required the use of variable speed drives for SPIM, where the adoption of sensorless techniques is the more reasonable option for speed control due to the low cost of this electrical machine. A proposal for sensorless variable speed SPIM drive based on direct rotor field orientation techniques is presented in this paper. None transformation is used in order to eliminate the asymmetry of the stator windings…
Sensorless variable speed single-phase induction motor drive system
2012
It is usual find single-phase induction motor (SPIM) in several house, office, shopping, farm, and industry applications, which are become each time more sophisticated and requiring variable speed drives. Considering the low cost of this machine, the adoption of sensorless speed control is the more reasonable option for SPIM drives. This paper presents a proposal for sensorless variable speed SPIM drive based on direct rotor field orientation techniques. An observer based on two independent linear close-loop control systems provides the estimation of the rotor flux and speed from the measurements of the stator currents and voltages. These estimatives are used by close-loop systems for speed…
Speed control of tubular linear induction motors for industrial automated applications
2016
The Tubular Linear Induction Machine (TLIM) has acquired great relevance over the past years for industrial automated applications. For this purpose, the complete modeling, simulation and determination of the parameters of a TLIM is presented in this paper. In addition, the TLIM speed control for this specific application is here described. In order to verify the performances of the proposed system, a test bench has been setup and good agreement is shown from the comparison between measured and simulated results.
A comparison among different kinds of stator lamination in tubular linear machines
2016
In this paper the authors perform a comparison among three different stator structures for a Tubular Permanent Magnet Linear Machine. Each structure is characterized by its own lamination which is expected to contribute to the overall performance of the machine. A detailed analysis of the main figures of merit of the three configurations has been carried out in order to identify the configuration with the best characteristics. Significant data such as flux distribution, rated voltage and current, force on the moved and power losses have been compared. The results show that the choice of a mixed stator lamination allows to improve the performance of these machines.