Search results for "Tito"
showing 10 items of 719 documents
Sensorless low Range Speed Estimation and Parameter Identification of Induction Motor Drives Devoted to Lifts Automatic Rescue Devices
2010
In this paper a sensorless rotor speed estimation and parameter identification algorithm is presented. The algorithm is designed specifically for induction motor (IM) drives devoted to automatic rescue devices (ARD) used in lifts and hoist applications. Its peculiarity is that it is based on the sinusoidal steady state mathematical model of the IM and, therefore, can be implemented on a low cost micro-controller in a simple way, however without lacking in terms of dynamic performance. It is also capable of self tuning so that no information is required about the specific IM used in the ARD drive. Finally the algorithm allows also an appreciable energy saving of the ARD when compared to olde…
Experimental investigation on high efficiency real-time control algorithms for IPMSMs
2014
This paper describes an experimental investigation on the power losses variations occurring in an Interior Permanent Magnet Synchronous Motor (IPMSM) with respect to the direct axis current component. Such investigation can be useful to determine a mathematical model accounting for copper, iron and mechanical friction losses, and for the arrangement of a speed control drive system equipped with a real-time power losses minimization algorithm. In particular, a test bench has been set up in order to carry out all measurements and the final power loss identification. The test bed is composed by a IPMSM drive with a field oriented control (FOC) strategy, a power analyzer, a dynamometric brake a…
Integration of distributed on site control actions via combined photovoltaic and solar panels system
2009
A systematic evaluation of the potential energy saving and CO2 emissions reduction on buildings was carried out, when a renewable energy system is locally installed. The exploitation of a combined solar and photovoltaic system and the integration of suitable energy management actions were deeply investigated. A model of these solar and photovoltaic components has been developed and included within a complete house simulator, capable to precisely figure out the daily electric energy consumptions of typical apartments and to measure the positive actions induced by the added renewable energy. Saving up to 40% on the energy consumptions and even more savings on wiring losses seems to be easily …
Fast procedure for the calculation of maximum slot filling factors in electrical machines
2017
This paper presents an algorithm for the calculation of maximum slot filling factor in electrical machines. The determination of whole wire cross section that occupy the area of a stator slot is very important in order to estimate the copper losses: The greater is the filling factor the lower are copper losses. The main goal of this paper is to define a simple algorithm for the determination of slot filling factors suitable for all type of slot profiles. The algorithm can be considered as an additional useful tool for the fast design of electrical machine windings.
The effect of manufacturing tolerances on a tubular linear ferrite motor
2015
This study presents a numerical and experimental study on the effect of permanent magnet tolerances on the performances of a Tubular Linear Ferrite Motor. The statistical distribution of the magnetic characteristic of a set of commercial magnets is obtained experimentally while the performances of a the tubular motor are numerically evaluated. The performances that have been considered are: cogging force, end effect force and generated thrust. It has been shown that: 1)the statistical variability of the magnets modifies the time behavior of the cogging force; 2)the value of both the end effect cogging force and the generated thrust are directly linked to the values of then remanence field o…
Vibration signature analysis for monitoring rotor broken bar in double squirrel cage induction motors based on wavelet analysis
2014
Purpose – The purpose of this paper is to present a diagnosis technique, for rotor broken bar in double cage induction motor, based on advanced use of wavelet transform analysis. The proposed technique is experimentally validated. Design/methodology/approach – The proposed approach is based on a combined use of frequency sliding and wavelet transform analysis, to isolate the contribution of the rotor fault components issued from vibration signals in a single frequency band. Findings – The proposed technique is reliable for tracking the rotor fault components over time-frequency domain. The quantitative analysis results based on this technique are the proof of its robustness. Research limit…
Italian incentive strategy and regulations on small wind power turbines: A critical overview
2016
Small wind power industry in Italy had its kick-start in 2009, after the Government implemented two measures introducing both the simplified regime and incentive rates for small wind power plants. In the last six years, a lot of plants and small wind turbines have been installed in Italy, especially in the South. Aim of this paper is to examine how local standards, incentive policy and regulations have affected the spread of small wind turbines in Italy. After examining national and regional legislation, an analysis of the data on the penetration of wind systems in Italy has been carried out, with particular attention to six Southern regions (Basilicata, Calabria, Campania, Apulia, Sardinia…
Finite-Difference Time-Domain Simulation of Tower and Grounding Subjected to Lightning
2015
In this paper the behavior of a tower and its grounding system, subjected to a lightning, is faced. Finite difference time domain (FDTD) method has been chosen in order to study the non-linear time domain behavior of the system. The electromagnetic problem has been described by using two type of first order time derivative equations: Maxwell's equations and Telegraph equations. Aim of this work is to evaluate the possibility of a flashover between tower and power line, by considering different cases of study.
The Jiles Atherton Model for Description Of Hysteresis in Lithium Battery
2013
In this paper Jiles Atherton (JA) Model is used to obtain a mathematical model of the hysteresis in lithium battery. JA Model allows to describe both the hysteresis and the dynamical features of charging and discharging cycles in a lithium battery. The identification of the model is obtained by using a neural network technique developed for magnetic systems. The model is validated on some experimental tests on commercial batteries.
Manufacturing tolerances effects on PV array energy production
2014
This paper investigates the tolerance effects of commercial photovoltaic modules in terms of electrical energy reduction of photovoltaic plants. Several commercial modules, having the same rated power, present different power tolerance values. A wide tolerance is an indicator of possible defects or differences in the production process and is responsible of remarkable reductions in the electricity production of photovoltaic plants. In this paper, thanks to the development of a suitable simulation tool, several simulations have been carried out, considering different tolerance and shading conditions for the PV array. Simulation results quantify the peak power value of the different plant con…