Search results for "Torque"
showing 10 items of 373 documents
Dynamic analysis of a five degree of freedom robotic arm using MATLAB-Simulink Simscape
2021
In this paper, a dynamic analysis for a 5 degree of freedom (DOF) robotic arm with serial topology is presented. The dynamic model of the robot is based on importing a tri-dimensional CAD model of the robot into Simulink®-Simscape™-Multibody™. The dynamic model of the robot in Simscape is a necessary and important step in development of the mechanical structure of the robot. The correct choice of the electric motors is made according to the resistant joint torques determined by running the dynamic analysis. One can import complete CAD assemblies, including all masses, inertias, joints, constraints, and tri-dimensional geometries, into the model block. The first step for executing a dynamic …
Integrated Design Optimization of a 5-DOF Assistive Light-weight Anthropomorphic Arm
2011
An integrated dimensional and drive train optimization method was developed for light-weight robotic arm design. The method deals with the determination of optimal link lengths and the optimal selection of motors and gearboxes from commercially available components. Constraints are formulated on the basis of kinematic performance and dynamic requirements, whereas the main objective is to minimize the weight. The design of a human-like arm, which is 10 kg in weight with a load capacity of 5 kg, is described. An integrated dimensional and drive train optimizationmethod was developed for light-weight robotic armdesign. The method deals with the determination of optimallink lengths and the opti…
Performance Comparison of Electrical Motors equipped with slightly Asymmetrical Windings
2019
This paper presents a comparison between the performances of electrical machines equipped with slightly asymmetrical windings. More in detail, by modifying the stator geometry of an Interior Permanent Magnet Synchronous Machine equipped with a symmetrical winding configuration, other two slightly asymmetrical winding topologies are obtained. The three models are, then, analyzed by means of a finite element method (FEM) and the related results are compared in terms of cogging torque, static characteristics and leakage factor. The obtained results demonstrate that the adoption of slightly asymmetrical windings could be an interesting alternative solution during the design stage of electrical …
Torque peak reduction and overload monitoring of induction motors in offshore drilling operations
2015
Current drivetrain design procedures for electric actuation systems operating in offshore conditions typically consider two major requirements: to provide sufficient steady-state and maximum motor torques. As a result of this, no information regarding the transient state (e.g. during motor acceleration) is utilized when selecting drivetrain components. This leads to potentially dangerous situations when motors undergo saturation in these regions due to too high dynamic loads. A common reason for this (apart from lack of information about transient state when designing a drivetrain) is applying trapezoidal reference motion profiles that cause discontinuities in system acceleration and infini…
Evaluation of performance and efficiency and type approval of an electrically assisted bicycle drive
2013
The diffusion of electrically assisted bicycles gives rise to the need of the evaluation of the performance and efficiency of the electric drive that supply it. In this paper, is presented a test bench for the estimation of the electric drive output torque under several speed and load conditions. Moreover, the test bench detects the electrical and mechanical parameters that allow to evaluate the electrical drive efficiencies. The test bench has been designed in agreement with the Directive 2002/24/EC of the European Parliament since it detects the maximum continuous rated power (that must be lower than 0.25 kW) and evaluates if the output is progressively reduced and finally cut off as the …
Dynamical Compensation of the Load Torque in a High-Performance Electrical Drive with an Induction Motor
2018
This paper describes a new method for dynamical estimation of load disturbance in induction motors by using Nonlinear Unknown Input Observers (NUIO). This estimation is then used to compensate dynamically the load torque in a Field Oriented Control (FOC) induction motor drive to increase its load-rejection capability. The method has been verified both in simulation and experimentally on a experimental rig.
An adaptive control law for robotic manipulator without velocity feedback
2003
In this paper, a new adaptive control law is designed for robotic manipulators, based on the use of reference velocities instead of the actual ones and feedback signals generated from position errors. The law in question is suitable for trajectory tracking and positioning tasks. Its peculiarities are implementation without velocity measurements and estimation, high signal-to-noise ratio in control torques and absence of parameter drift in positioning tasks. Experimental tests are shown with the aim to confirm the validity of the control law and to illustrate its actual effects on the behaviour of the system.
A CONTROL LAW FOR ROBOTIC MANIPULATORS BASED ON A FILTERED SIGNAL TO GENERATE PD ACTION AND VELOCITY ESTIMATES
2007
This paper deals with an adaptive control law for robotic manipulators based on a filtered signal to generate both the PD action and velocity estimates of the joints, suitable for trajectory tracking tasks, with the particular aim of reducing the harmonic content of the mechanical torques developed at the joints and thus avoiding excitation of unmodelled dynamics and instability. The practical aspects relative to the implementation of the control law are considered as relevant and, consequently, are detailed. In particular, several methods suitable to compute velocity estimates are discussed and compared with the method described in the paper. All of the above methods are illustrated by mea…
Adaptive real-time estimation on road disturbances properties considering load variation via vehicle vertical dynamics
2013
Published version of an article in the journal: Mathematical Problems in Engineering. Also available from the publisher at: http:/dx.doi.org/10.1155/2013/283528 Open Access Vehicle dynamics are directly dependent on tire-road contact forces and torques which are themselves dependent on the wheels' load and tire-road friction characteristics. An acquisition of the road disturbance property is essential for the enhancement of vehicle suspension control systems. This paper focuses on designing an adaptive real-time road profile estimation observer considering load variation via vehicle vertical dynamics. Firstly, a road profile estimator based on a linear Kalman filter is proposed, which has g…
Angle Displacement Robust Controller for the Port Plate of the Hydraulic Transformer
2013
The hydraulic transformer is used in the hydraulic system to enhance the efficiency. However, how to control the angle displacement of the port plate is becoming a critical issue because of the new structure of the hydraulic transformer. This paper presents a new method for the angle displacement control system. Firstly, the basic principle of the system is presented. Then, the disturbance which is mainly the friction torque between the port plate and the cylinder block is calculated to estimate the range. Furthermore, the guaranteed cost control (GCC) is analyzed and combined with the disturbance and the characteristics of parameter uncertainties. Finally, the proposed control method is co…