Search results for "Turing"

Comparison of the relative quantities of aroma compounds found in fresh apricot (Prunus armeniaca) from six different varieties

1988

The volatile components of fresh apricot (Prunus armeniaca) were isolated by vacuum distillation and fractionated on a silica gel column. Analysis by gaschromatography coupled with mass spectrometry led to the identification of 82 compounds, 60 of which were found for the first time in this fruit. Six varieties, cultivated in the south of France were compared for their firmness, acidity, sweetness and for their content of 56 volatile components. Precoce de Tyrinthe was the least aromatic variety, but produced fruits very early in the season. Palsteyn gave acidic but rather aromatic fruits. Moniqui possessed large but perishable fruits with flowery aroma due to the presence of terpenic keton…

Relationship between erythemal UV and broadband solar irradiation at high altitude in Northwestern Argentina

2018

An analysis of the broadband solar irradiation, IT, and the erythemal UV irradiation, IUVER, has been performed using the measurements made from 2013 to 2015 at three sites located at altitudes over 1000 m a.s.l. In Northwestern Argentina (Salta, El Rosal, and Tolar Grande). The main objective of this paper is to determine a relationship between IT and IUVER, which would allow to estimate IUVER from IT in places with few IUVER measurements available, and especially in those where is important to establish adequate photoprotection measures given their dense population and location at high altitude. The relationship between the daily values of IUVER and IT has been fitted to a linear regressi…

Emissitivity spectra obtained from field and laboratory measurements using the temperature and emissivity separation algorithm.

2006

Surface emissivities play an important role in thermal remote sensing, since knowledge of them is required to estimate land surface temperature with enough accuracy. They are also important in other environmental or geological studies. We show the results obtained for the emissivity spectra of different natural surfaces (water, green, and senescent vegetation) by applying the temperature and emissivity separation (TES) algorithm to ground-based measurements collected at the field with a multiband thermal radiometer. The results have been tested with data included in spectral libraries, and rms errors lower than 0.01 have been found, except for senescent vegetation. Two methods are also prop…

Soil emissivity and reflectance spectra measurements

2009

We present an analysis of the laboratory reflectance and emissivity spectra of 11 soil samples collected on different field campaigns carried out over a diverse suite of test sites in Europe, North Africa, and South America from 2002 to 2008. Hemispherical reflectance spectra were measured from 2.0 to 14 microm with a Fourier transform infrared spectrometer, and x-ray diffraction analysis (XRD) was used to determine the mineralogical phases of the soil samples. Emissivity spectra were obtained from the hemispherical reflectance measurements using Kirchhoff's law and compared with in situ radiance measurements obtained with a CIMEL Electronique CE312-2 thermal radiometer and converted to emi…

Application of the SKYRAD Improved Langley plot method for the in situ calibration of CIMEL Sun-sky photometers

2007

The in situ procedure for determining the solar calibration constants, originally developed for the PREDE Sun-sky radiometers and based on a modified version of the Langley plot, was applied to a CIMEL instrument located in Valencia, Spain, not integrated into AERONET. Taking into account the different mechanical and electronic characteristics of the two radiometers, the method was adapted to the characteristics of the CIMEL instrument. The iterative procedure for the determination of the solar calibration constants was applied to a 3-year data set. The results were compared with the two sets of experimental calibration constants determined during this period using the standard Langley plot…

Using mRNA and small RNA gene expression changes in peripheral blood for easy detection of Ra-223 incorporation

2019

Two-color ionization of hydrogen by short intense pulses

2010

Photoelectron energy spectra resulting by the interaction of hydrogen with two short pulses having carrier frequencies, respectively, in the range of the infrared and XUV regions have been calculated. The effects of the pulse duration and timing of the X-ray pulse on the photoelectron energy spectra are discussed. Analysis of the spectra obtained for very long pulses show that certain features may be explained in terms of quantum interferences in the time domain. It is found that, depending on the duration of the X-ray pulse, ripples in the energy spectra separated by the infrared photon energy may appear. Moreover, the temporal shape of the low frequency radiation field may be inferred by …

Asymmetric Single Point Incremental Forming of Sheet Metal

2005

The use of computers in manufacturing has enabled the development of several new sheet metal forming processes, which are based upon older technologies. This paper describes modifications that have been made to traditional forming methods such as conventional spinning and shear forming, forming processes in which deformation is localized. Recent advances have enabled this localized deformation to be accurately controlled and studied. Current developments have been focused on forming asymmetric parts using CNC technology, without the need for costly dies. Asymmetric Incremental Sheet Forming has the potential to revolutionize sheet metal forming, making it accessible to all levels of manufac…

Incremental Forming Process for the Accomplishment of Automotive Details

2007

In the last decades the scenario of the industrial production is remarkably changed, since new market requirements have to be faced by the industries. The market, actually, more and more, asks for vary models and niches product. The necessity to intercept dynamically and to satisfy the demands for the market, driver of the innovation process, involves the necessity to reduce the Timeto- market introducing to new methodologies of engineering, like the 3D-prototyping, for the qualitative and structural analysis of the final component. For these reasons, at the beginning of the nineties, a new philosophy of sheet metal forming process begins to assert on the industrial scene, whose basic logic…

Laser Ablation of Poly(lactic acid) Sheets for the Rapid Prototyping of Sustainable, Single-Use, Disposable Medical Microcomponents

2018

The employment of single-use, disposable medical equipment has increased the amount of medical waste produced and the advent of point-of-care diagnostics in lab-on-chip format is likely to add further volume. Current materials used for the manufacture of these devices are derived from petroleum sources and are, therefore, unsustainable. In addition, disposal of these plastics necessitates combustion to reduce infection risk, which has, depending on material composition, an undesirable environmental impact. To address these issues, we have developed a general approach for the rapid prototyping of single-use point-of-care cartridges prepared from poly(lactic acid), a sustainable material whic…