Search results for "Ultrasonics"
showing 10 items of 326 documents
Machine learning at the interface of structural health monitoring and non-destructive evaluation
2020
While both non-destructive evaluation (NDE) and structural health monitoring (SHM) share the objective of damage detection and identification in structures, they are distinct in many respects. This paper will discuss the differences and commonalities and consider ultrasonic/guided-wave inspection as a technology at the interface of the two methodologies. It will discuss how data-based/machine learning analysis provides a powerful approach to ultrasonic NDE/SHM in terms of the available algorithms, and more generally, how different techniques can accommodate the very substantial quantities of data that are provided by modern monitoring campaigns. Several machine learning methods will be illu…
Detection, characterization and sizing of hydrogen induced cracking in pressure vessels using phased array ultrasonic data processing
2016
Abstract Pressure vessels operating in sour service conditions in refinery environments can be subject to the risk of H₂S cracking resulting from the hydrogen entering into the material. This risk, which is related to the specific working conditions and to the quality of the steel used, shall be properly managed in order to maintain the highest safety at a cost-effective level. Nowadays the typical management strategy is based on a risk based inspection (RBI) evaluation to define the inspection plan used in conjunction with a fitness for service (FFS) approach in defining if the vessel, although presenting dangerous defects such as cracks, can still be considered “fit for purpose” for a giv…
Laser Ultrasonics Inspection of Train Wheel - Evaluation of Optimized Setup
2021
In the railway field, the safety of passengers and the service life of train components are a crucial issue. For this reason, continuous periodic inspections by non-destructive techniques are required. Among these, ultrasonic tests are widely used in this field, even though the conventional ultrasound techniques have the disadvantage of requiring the disassembly of the wheels and of putting the train out of service. This procedure is expensive and time-consuming and can be neglected if non-contact ultrasonic techniques are used. In this work, the authors present an experimental research on some defects, artificially obtained on a railway wheel supplied by Trenitalia Spa, by adopting three d…
Magnetization of3He spin filter cells
2007
A number of valved quartz glass 3He spin filter cells have been repeatedly exposed to various external magnetic fields in order to determine the influence of induced wall magnetization on the relaxation time in the cells. The procedures of magnetizing and degaussing of cells are described. A comparison of T1 measurements performed in the same cell by different methods attest the good reliability of the measurements as well as the time stability of T1 in Cs-coated quartz glass cells. No orientation dependence of the relaxation in fields of 8 G was observed. A strong dependence of T1 on the strengths of external magnetic fields, applied perpendicular to the direction of the guide field used d…
Non-chromatographic speciation of toxic arsenic in vegetables by hydride generation-atomic fluorescence spectrometry after ultrasound-assisted extrac…
2007
A non-chromatographic, sensitive and simple analytical method has been developed for the determination of toxic arsenic species in vegetable samples by hydride generation-atomic fluorescence spectrometry (HG-AFS). As(III), As(V), dimethylarsinic acid (DMA) and monomethylarsonic acid (MMA) were determined by hydride generation-atomic fluorescence spectrometry using a series of proportional equations. The method is based on a single extraction of the arsenic species considered from vegetables through sonication at room temperature with H(3)PO(4) 1 mol L(-1) in the presence of 0.1% (w/v) Triton XT-114 and washing of the solid phase with 0.1% (w/v) EDTA, followed by direct measurement of the co…
Electronic structure and transport properties of the Heusler compound Co2TiAl
2009
The properties of the Heusler compound Co2TiAl were investigated in detail by experimental techniques and theoretical methods. X-ray diffraction measurements indicate that as-cast samples of the compound exhibit the L21 structure with a small amount of B2-type disorder. This leads to a reduced saturation magnetization per formula unit of 0.747 μB. The Curie temperature is approximately 120 K. The transport properties are influenced by the change in the electronic structure at the Curie temperature, as revealed experimentally by conductivity, thermal transport and specific heat measurements. Different theoretical models based on ab initio calculations of the electronic structure are used to …
Structural and magnetic properties of Fe2CoGa Heusler nanoparticles
2012
Abstract Fe2CoGa Heusler nanoparticles are synthesized by a chemical method. The structure and magnetic properties of Fe2CoGa Heusler nanoparticles are investigated by x-ray diffraction, extended x-ray absorption fine structure and Mössbauer spectroscopy. The crystal structure of Fe2CoGa nanoparticles is described by the X-type structure (prototype: Li2AgSb). Magnetic measurements reveal the presence of small Fe2CoGa nanoparticles and lower magnetic moments compared with the theoretically predicted values.
Gilbert damping of CoFe-alloys
2019
We report structural, magnetic and dynamic properties of polycrystalline Coalt;subagt;xalt;/subagt;Fealt;subagt;1-xalt;/subagt;-alloy films on Sapphire, Silicon and MgO substrates across the full composition range, by using a Vector Network Analyser ferromagnetic resonance measurement technique (VNA-FMR), Superconducting Quantum Interference Device magnetometry (SQUID) and X-Ray Diffraction (XRD). In the approximate vicinity of 28% Co, we observe a minimum of the damping parameter, associated with a reduction in the density of states to a minimum value at the Fermi energy level. For films on all substrates, we find magnetic damping of the order of 4-5⋅10alt;supagt;-3alt;/supagt;, showing th…
Transfer matrix method applied to the parallel assembly of sound absorbing materials
2013
International audience; The transfer matrix method (TMM) is used conventionally to predict the acoustic properties of laterally infinite homogeneous layers assembled in series to form a multilayer. In this work, a parallel assembly process of transfer matrices is used to model heterogeneous materials such as patchworks, acoustic mosaics, or a collection of acoustic elements in parallel. In this method, it is assumed that each parallel element can be modeled by a 2 × 2 transfer matrix, and no diffusion exists between elements. The resulting transfer matrix of the parallel assembly is also a 2 × 2 matrix that can be assembled in series with the classical TMM. The method is validated by compar…
Digital signal processing for rail monitoring by means of ultrasonic guided waves
2007
Recent train accidents have reaffirmed the need for developing rail defect detection systems that are more effective than those used today. One of the recent developments in rail inspection is the use of ultrasonic guided waves (UGWs) and non-contact probing techniques to target transverse-type defects. Besides the obvious advantages of non-contact probing, that include robustness and a potential for large inspection speed, such a system can theoretically detect transverse defects under horizontal shelling or head checks. This paper demonstrates the effectiveness of digital signal processing to enhance the damage detection sensitivity of the non-contact system. The method proposed here comb…