Search results for "VISCOSITY"
showing 10 items of 542 documents
No-flow temperature and solidification in injection molding simulation
2011
The no‐flow temperature (NFT) is a parameter representing the rheological solidification temperature of a polymer. A polymer, during injection molding filling stage, can stop its flow because of its high viscosity, although it is not yet fully solidified by means of glass transition or crystallization. The NFT is used in most of injection molding simulation packages: with this simple parameter it is possible to reduce the errors deriving from viscosity extrapolation at relatively low temperatures. The viscosity measurements for polymers are usually carried out at high temperatures, and the viscosity models can fail in prediction at temperatures close to the glass transition or crystallizati…
Consequences of linking charged and uncharged monomers to binary copolymers studied in dilute solution. Part I: Viscometric behavior of the homopolym…
2017
Abstract Intrinsic viscosities, generalized intrinsic viscosities and viscometric interaction parameters were measured for aqueous solutions of poly(ethylene oxide) [PEO], poly(N,N-dimethyl aminoethyl methacrylate) [PR] (uncharged) and for poly{[2-(methacryloyloxy)ethyl] trimethylammonium iodide} [PR+] (charged) within a wide range of molar masses. In this manner it was possible to establish the information required for the study of non-additivity effects upon the formation of binary copolymers from the monomers specified above. The following additional items were of particular interest: The effects of charging PR to PR+ and the composition dependence of the coil overlap in the case of sali…
Viscosity-molecular weight relationship for cellulose solutions in either NMMO monohydrate or cuen
2010
The intrinsic viscosities, [η], of nine cellulose samples, with molar masses from 50 × 103 to 1 390 × 103 were determined in the solvents NMMO*H2O (N-methyl morpholin N-oxide hydrate) at 80°C and in cuen (copper II-ethlenediamine) at 25°C. The evaluation of these results with respect to the Kuhn–Mark–Houwink relations shows that the data for NMMO*H2O fall on the usual straight line in the double logarithmic plots only for M ≤ 158 103; the corresponding [η]/M relation reads log ([η]/mL g−1) = –1.465 + 0.735 log M. Beyond that molar mass [η] remains almost constant up to M ≈ 106 and increases again thereafter. In contrast to NMMO*H2O the cellulose solutions in cuen behave normal and the Kuhn–…
Molecular characterization of α , β -poly(asparthylhydrazide) a new synthetic polymer for biomedical applications
1999
Abstract α , β -Poly(asparthylhydrazide) (PAHy) is a new synthetic polymer that exhibits interesting properties and is a candidate for biomedical applications. In this article the characterization of PAHy polymer by multi-angle laser light scattering (MALS) and single-capillary viscometer (SCV) detectors on-line to a size exclusion chromatography (SEC) system is reported. The SEC–MALS–SCV system furnishes exhaustive and consistent characterization of the PAHy polymer. Further, it is possible to characterize the PAHy polymer through conventional SEC and universal calibration. The universal calibration method gives intrinsic viscosity and dispersity very close to those measured by the absolut…
Polymer-polymer interaction, in the presence of a solvent as measured by viscometry
2001
Dilute solution viscometry experiments have been carried out in five ternary polymer systems solvent(1)/polymer(2)/polymer(3). Values of the specific viscosity of polymer (3) in a ‘binary solvent’ formed by polymer(2) + solvent(1) have been used to determine the compatibility of the polymer blends. Krigbaum and Wall formalism has been used to predict compatibility which relies on an interaction parameter that depends on the concentration, weight fraction and molar mass of each polymer. To reduce the dependences and to clarify the criterion of compatibility, a parameter independent of polymer (3) composition and molar mass has been deduced. This parameter shows the same behaviour with polyme…
Thermo-Mechanical Degradation of LDPE-Based Nanocomposites
2007
Thermo-mechanical degradation of LDPE-based nanocomposites was studied by mainly investigating the rheological properties. For all of the investigated processing conditions, the viscosity of the nanocomposites was higher than that of the pure-LDPE matrix, but on increasing the severity of the mixing conditions, the difference between the viscosity of the nano-filled polymer and that of the pure LDPE decreased. The X-ray traces of the nanocomposites suggest that intercalation has been achieved during the melt, when less-severe processing conditions were used. At severe processing conditions (longer mixing time, high temperature and shear stress) the thermo-mechanical degradation was accelera…
Influence of polymer flexibility on nanoparticle dynamics in semidilute solutions
2018
The hierarchical structure and dynamics of polymer solutions control the transport of nanoparticles (NPs) through them. Here, we perform multi-particle collision dynamics simulations of solutions of semiflexible polymer chains with tunable persistence length lp to investigate the effect of chain stiffness on NP transport. The NPs exhibit two distinct dynamical regimes - subdiffusion on short time scales and diffusion on long time scales. The long-time NP diffusivities are compared with predictions from the Stokes-Einstein relation (SER), mode-coupling theory (MCT), and a recent polymer coupling theory (PCT). Increasing deviations from the SER as the polymer chains become more rigid (i.e. as…
Composite soy lecithin–decylpolyglucoside vesicles: A theoretical and experimental study
2008
In the present work, vesicles made with soy lecithin and a commercial mixture of alkyl polyglucosides were prepared and characterized. Vesicles with a constant amount of soy lecithin and an increasing amount of a decylpolyglucoside surfactant, (OrNS10), were formulated and their physicochemical properties were studied with the aim to design a drug delivery system suitable for different applications. To this purpose, morphology, size distribution, ζ-potential and apparent viscosity of the prepared vesicles were studied. Vesicles were also characterized by using optical and light polarized microscopy, transmission electron microscopy and photon correlation spectroscopy. A stability study was …
Are polymers suitable rock analogs?
2002
To evaluate if a polymer is suitable for analog modeling, it is essential to know the rheological properties of the material. Polymers used in analog modeling exhibit a complex rheological behavior; only part of which has been taken into account in most modeling studies. The mechanical behavior is strongly dependent on strain rate and temperature, and is characterized by specific dependencies of the storage and loss moduli, related to the elasticity and viscosity, on the deformation rate (frequency). We have measured the storage and loss moduli at a broad range of strain rates and strains, using an oscillatory parallel-disk rheometer. Investigated materials are polydimethylsiloxane (PDMS), …
Intrinsic viscosities of polyelectrolytes in the absence and in the presence of extra salt: Consequences of the stepwise conversion of dextran into a…
2011
Abstract Viscosities of dilute polymer solutions were measured in capillary viscometers for samples varying in their fraction f of charged units from 0.00 to 0.90. The dependence of the logarithm of the relative viscosity on polymer concentration c is in all cases reproduced quantitatively by three characteristic parameters: [ η ], the intrinsic viscosity; B , a viscometric interaction parameter (related to the Huggins constant); [ η ] , a parameter required only for polyelectrolytes at low concentrations of extra salt. In pure water [ η ] increases more than 80 times as the fraction f rises from zero to 0.90 and [ η ] starts from zero and goes up to ≈71 mL/g. Upon the addition of NaCl [ η …