Search results for "Ven"
showing 10 items of 31764 documents
Energy and economic analysis of air-to-air heat pumps as an alternative to domestic gas boiler heating systems in the South of Italy
2019
Abstract According to the electricity tariff recently issued by the Italian government for the domestic heating systems fed with heat pumps (HP), an energy and economic analysis was carried out with the aim of investigating the effectiveness of the air-to-air heat pump systems (HPS) as an alternative to the traditional heating using domestic gas boilers systems (GBS). For the purpose of this study, the apartments of three residential buildings were examined. The hourly heating loads were calculated with the ASHRAE radiant time series and the coefficient of performance (COP) of the HPs was evaluated for each operating condition. The costs for the heating system installation and electricity a…
Solar and Heat Pump Systems for Domestic Hot Water Production on a Small Island: The Case Study of Lampedusa
2020
The achievement of United Nations Sustainable Development Goals, related to energy and resource use, is a critical issue for small and insulated communities. In many minor islands, solar energy is not correctly exploited, and electrical heaters are connected to weak grids with very a high share of generation by fossil fuels. As a consequence, there is the necessity to assess the potential and the suitability of diffusion of alternative systems to avoid dependency on the electrical grid and reduce carbon emissions. This paper aims to evaluate the technical and economic performances of some alternative systems exploiting renewable energy for domestic hot water production. Four different syste…
Optimization of 3-DOF Parallel Motion Devices for Low-Cost Vehicle Simulators
2017
Motion generation systems are becoming increasingly important in certain Virtual Reality (VR) applications, such as vehicle simulators. This paper deals with the analysis of the Inverse Kinematics (IK) and the reachable workspace of a three-degrees-of-freedom (3-DOF) parallel manipulator, proposing different transformations and optimizations in order to simplify its use with Motion Cueing Algorithms (MCA) for self-motion generation in VR simulators. The proposed analysis and improvements are performed on a 3-DOF heave-pitch-roll manipulator with rotational motors, commonly used for low-cost motion-based commercial simulators. The analysis has been empirically validated against a real 3-DOF …
Phase-noise Impact on the Performance of mmWave-radars
2019
The impact of phase noise in Frequency Modulated Continuous Wave (FMCW) millimeter-wave (mmWave) radars is investigated in this paper. A FMCW signal is transmitted from the radar, reflected off a moving object and processed at a receiver in the radar. The impact of random phase noise/jitter on the performance parameters of estimated distance, speed and angle of arrival of an object is studied. Our studies show that there exists a threshold at about fifteen percent of the period of the carrier frequency, over which errors substantially manifest in the estimations. Distance estimation is less affected than speed and angle, which rely directly on the phase information for the estimations. Angl…
Partial Stabilization of Input-Output Contact Systems on a Legendre Submanifold
2017
This technical note addresses the structure preserving stabilization by output feedback of conservative input-output contact systems, a class of input-output Hamiltonian systems defined on contact manifolds. In the first instance, achievable contact forms in closed-loop and the associated Legendre submanifolds are analysed. In the second instance the stability properties of a hyperbolic equilibrium point of a strict contact vector field are analysed and it is shown that the stable and unstable manifolds are Legendre submanifolds. In the third instance the consequences for the design of stable structure preserving output feedback are derived: in closed-loop one may achieve stability only rel…
Consistent Clustering of Elements in Large Pairwise Comparison Matrices
2018
[EN] In multi-attribute decision making the number of decision elements under consideration may be huge, especially for complex, real-world problems. Typically these elements are clustered and then the clusters organized hierarchically to reduce the number of elements to be simultaneously handled. These decomposition methodologies are intended to bring the problem within the cognitive ability of decision makers. However, such methodologies have disadvantages, and it may happen that such a priori clustering is not clear, and/or the problem has previously been addressed without any grouping action. This is the situation for the case study we address, in which a panel of experts gives opinions…
Enhancing the sound absorption of small-scale 3D printed acoustic metamaterials based on Helmholtz resonators
2018
Acoustic metamaterials have recently become of interest for their ability to attenuate sound by breaking the mass-density law. In this paper, acoustic metamaterials based on Helmholtz resonators and capable of attenuating sound up to 30 dB are fabricated for sound absorption applications in the small scale. The proposed metamaterials are subwavelength at a factor of $\lambda /12$ with respect to the lateral dimension of the units. The directional response due to the position of the acoustic source on the sound attenuation provided by the metamaterial is investigated by controlling the location of a loudspeaker with a robot arm. To enhance and broaden the absorption bands, structural modific…
Aircraft wing rock oscillations suppression by simple adaptive control
2020
Abstract Roll angular motion of the modern aircraft operating in non-linear flight modes with a high angle of attack often demonstrates the limit cycle oscillations, which is commonly known as the wing rock phenomenon. Wing rock dynamics are represented by a substantially non-linear model, with parameters varying over a wide range, depending on the flight conditions (altitude, Mach number, payload mass, etc.) and angle of attack. A perspective approach of the wing rock suppression lies in the adaptation methods. In the present paper an application of the simple adaptive control approach with the Implicit Reference Model (IRM) is proposed and numerically studied. The IRM adaptive controller …
Mechanical and metallurgical characterization of AA6082-T6 sheet-bulk joints produced through a linear friction welding based approach
2020
In the last decades, new flexible manufacturing processes have been developed to face the demands, by many industrial fields, for highly customized complex functional parts. The peculiar design of these components often overcomes conventional sheet metal and bulk metal forming processes capabilities. In order to face this issue, new hybrid techniques, capable of exploit key advantages of different processes, have to be developed. In this study, a method to obtain sheet-bulk joints, based on the Linear Friction Welding process, is proposed. The feasibility of the technique was investigated through an experimental campaign carried out with varying pressure and oscillation frequency using AA60…
Novel Threshold Calculations for Remaining Useful Lifetime Estimation of Rolling Element Bearings
2018
The prognostics objective is to avoid sudden machinery breakdowns and to estimate the remaining useful life after initial degradation. Typically, physical health indicators are derived from available sensor data, and a mathematical model is tuned to fit them. The time it takes for the model to reach a failure threshold is the estimated remaining useful life. The failure threshold may be determined from historical failure data, but that is not always readily available. ISO standard 10816–3 defines permissible velocity vibration levels for machines that may be used as a failure threshold. However, velocity vibration is not suitable for bearing prognostics due to the effect of integration from…