Search results for "Vent"

Through-transmission laser welding of polymers – temperature field modeling and infrared investigation

2007

The purpose of the present study is to estimate the weldability of a polymeric material couple according to their thermal and optical properties. A first model based on Mie theory and Monte Carlo method describes the laser beam behavior in semi-transparent media and makes it possible to approximate the laser power distribution at the interface of the two materials. A second model based on finite element method permits the temperature field estimation into both parts to be welded. The results are validated by infrared thermography.

Laser-assisted narrow gap arc welding of an 18MND5 steel thick plate

2020

Abstract Narrow gap arc welding is a common solution for the welding of thick structures. In this study, a defocused laser beam is used to pre-melt the narrow gap walls in front of an arc-welding bath. Such a welding configuration can be referred to a hybrid welding configuration. In the present work, a particular attention is given to evaluation of the interaction between an arc plasma and a defocused laser beam. High-speed imaging of the metal transfer through arc plasma is achieved thanks to a diode laser illumination system. Electrical arc parameters are logged, synchronously, in order to perform a correlation analysis and to make a diagnosis of the interaction level between laser beam …

Inverse kinematic control of an industrial robot used in Vessel-to-Vessel Motion Compensation

2017

An increased level of complex offshore load handling operations is expected due to an increased amount of floating wind turbines, remote fish farms, and autonomous shipping, and in general more advanced operations to be carried out at sea. A common problem for these applications is that both equipment and personnel have to be transported between two floating vessels at sea. An investigation of the Vessel-to-Vessel Motion Compensation (VVMC) problem may increase the efficiency and safety of such operations in the future. In this paper, a control algorithm has been developed and experimentally tested in the Norwegian Motion Laboratory featuring two Stewart platforms (SPs), an industrial robot…

An intelligent Proportional controller of a Seeded Batch Crystallizer

2020

Crystallization process is used in a very wide range of industrial applications. However, highly nonlinear comportment of such process and the difficulties of characterizing several phenomenological effects makes difficult to find suitable operational procedures for producing required products. In this article, we use a model-free control (MFC) for controlling the mean size of crystals produced by seeded batch cooling crystallization. The MFC method is distinguished notably in terms of the modeling strategy. Rather than developing a crystallization model within the classic population balance equation (PBE) together with the mass balance and the energy balance, as is usually done, we use a l…

Analysis of Linear Feedback Position Control in Presence of Presliding Friction

2016

Parallel distributed compensation for voltage controlled active magnetic bearing system using integral fuzzy model

2018

Parallel Distributed Compensation (PDC) for current-controlled Active Magnetic Bearing System (AMBS) has been quite effective in recent years. However, this method does not take into account the dynamics associated with the electromagnet. This limits the method to smaller scale applications where the electromagnet dynamics can be neglected. Voltage-controlled AMBS is used to overcome this limitation but this comes with serious challenges such as complex mathematical modelling and higher order system control. In this work, a PDC with integral part is proposed for position and input tracking control of voltage-controlled AMBS. PDC method is based on nonlinear Takagi-Sugeno (T-S) fuzzy model. …

Assessing the accuracy of industrial robots through metrology for the enhancement of automated non-destructive testing

2016

This work presents the study of the accuracy of an industrial robot KR5 arc HW, used to perform quality inspections of components with complex shapes. Metrology techniques such as laser tracking and large volume photogrammetry were deployed to quantify both pose and dynamic path accuracies of the robot in accordance with ISO 9283:1998. The overall positioning pose inaccuracy of the robot is found to be almost 1 mm and path inaccuracy at 100% of the robot rated velocity is 4.5 mm. The maximum pose orientation inaccuracy is found to be 14 degrees and the maximum path orientation inaccuracy is 5 degrees. Despite of the significant maximum inaccuracies, uncertainty of a robotic scanning applica…

Registration of Surfaces Minimizing Error Propagation for a One-Shot Multi-Slit Hand-Held Scanner

2008

We propose an algorithm for the on-line automatic registration of multiple 3D surfaces acquired in a sequence by a new hand-held laser scanner. The laser emitter is coupled with an optical lens that spreads the light forming 19 parallel slits that are projected to the scene and acquired with subpixel accuracy by a camera. Splines are used to interpolate the acquired profiles to increase the sample of points and Delaunay triangulation is used to obtain the normal vectors at every point. A point-to-plane pair-wise registration method is proposed to align the surfaces in pairs while they are acquired, conforming paths and eventually cycles that are minimized once detected. The algorithm is spe…

Efficient Transport Protocol for Networked Haptics Applications

2008

The performance of haptic application is highly sensitive to communication delays and losses of data. It implies several constraints in developing networked haptic applications. This paper describes a new internet protocol called Efficient Transport Protocol (ETP), which aims at developing distributed interactive applications. TCP and UDP are transport protocols commonly used in any kind of networked communication, but they are not focused on real time application. This new protocol is focused on reducing roundtrip time (RTT) and interpacket gap (IPG). ETP is, therefore, optimized for interactive applications which are based on processes that are continuously exchanging data. ETP protocol i…

Additively manufactured textiles and parametric modelling by generative algorithms in orthopaedic applications

2020

Purpose The purpose of this paper is to implement a new process aimed at the design and production of orthopaedic devices fully manufacturable by additive manufacturing (AM). In this context, the use of generative algorithms for parametric modelling of additively manufactured textiles (AMTs) also has been investigated, and new modelling solutions have been proposed. Design/methodology/approach A new method for the design of customised elbow orthoses has been implemented. In particular, to better customise the elbow orthosis, a generative algorithm for parametric modelling and creation of a flexible structure, typical of an AMT, has been developed. Findings To test the developed modelling a…