Search results for "Viscoelastic"

Laboratory and in-situ tests for estimating improvements in asphalt concrete with the addition of an LDPE and EVA polymeric compound

2019

Abstract Pavement deformation is a critical issue in the design of pavement structures and the related mixture. Asphalt concretes may be very sensitive to this problem, in compliance with the viscoelastic behaviour of the adopted bitumen. To improve the material performance, many attempts have been made to introduce in the mixture other materials as “modifiers” or “additives” for increasing the permanent deformation resistance and the elastic modulus of the material. Among the different possible materials, polymers determined significant improvements in the road pavement performance. In this paper, the authors tested the adoption of a specifically engineered polymeric compound, in order to …

Effect of chain extender on the morphology, thermal, viscoelastic, and dielectric behavior of soybean polyurethane

2021

Physical behavior and morphology of biaxially rolled low-density polyethyleneX

1989

Abstract Biaxial rolling was carried out on low-density polyethylene, and the rolled samples were studied using various techniques. Scanning electron microscopy and analysis of transport properties were used to obtain structural information, which was correlated to thermomechanical and dynamic-mechanical behavior. Results indicate that the initial morphology is destroyed by rolling and that clumps of molecules, like fibrils, are generated parallel to the rolling plane. The molecular orientation in the plane is mainly radial, with some reinforcement, particularly at high rolling degree, along axes diagonal with respect to the rolling directions. The rolling drastically reduces the molecular …

Bending test for capturing the vivid behavior of giant reeds, returned through a proper fractional visco-elastic model

2015

Abstract This paper presents results of experimental investigations made to evaluate the vivid behavior of giant reed Arundo donax. In particular, attention was paid to the relationship between visco-elastic properties and moisture content, which is widely recognized as one of the key factor that influences the mechanical properties of all wood-based materials. To this aim, after a controlled drying treatment on samples of reed, stress relaxation tests in three point bending configuration were performed to evaluate the effects of moisture content on visco-elastic behavior of the giant reed. Further, the novel aspect of this paper is that of using an Euler–Bernoulli model embedded with an ad…

Rheological Response of Polyethylene/Clay Nanocomposites to Annealing Treatment

2007

The rheological response of a polyethylene/clay nanocomposite to annealing treatment under air and nitrogen atmospheres was studied. The treatment influences the rheology of the nanocomposite significantly. In particular, the viscosity and the non-Newtonian behavior dramatically increase with annealing time, and a liquid-like/solid-like transition is observed. The annealed samples were characterized by ATR-FT-IR spectrometry and it was shown that a silicate-rich layer is formed on the surface of the nanocomposite. This result was confirmed by TEM images of bulk and surface of annealed samples. It was demonstrated that the formation of this coating is the main cause of the change of rheologi…

Long-term ISO 23936-2 sweet oil ageing of HNBR

2021

Abstract A hydrogenated nitrile butadiene rubber (HNBR) compound is subjected to ageing in a simulated oil and gas environment in accordance with ISO 23936-2 standard at two elevated temperatures (130 °C and 150 °C) for a period of up to 9 months. Shore D hardness, thermal expansion, dynamic mechanical analysis (DMA), Fourier transform infrared (FTIR) spectroscopy, compression and compression set (CS) measurements are made before and after the chemical exposure. The hardness, modulus at short times, degree of relaxation and CS increases while the coefficient of thermal expansion in HNBR tends to decrease with ageing time and temperature. Temperature is shown to impose a greater effect on th…

Material valorisation of amorphous polylactide. Influence of thermo-mechanical degradation on the morphology, segmental dynamics, thermal and mechani…

2012

[EN] This paper reports the effects of multiple mechanical recycling on the structure and properties of amorphous polylactide (PLA). The influence of the thermo-mechanical degradation induced by means of five successive injection cycles was initially addressed in terms of macroscopic mechanical properties and surface modification. A deeper inspection on the structure and morphology of PLA was associated to the thermal properties and viscoelastic behaviour. Although FT-IR analysis did not show significant changes in functional groups, a remarkable reduction in molar mass was found by viscometry. PLA remained amorphous throughout the reprocessing cycles, but the occurrence of a cold-crystalli…

Linking structure and nanomechanical properties via instrumented nanoindentations on well-defined and fine-tuned morphology poly(ethylene)

2009

Several poly(ethylene) samples with a broad range of morphologies were studied in this work using nanoindentations. The samples had degrees of crystallinity ranging from 30 to 100% while their Young's modulus ranged from few tens of MPa up to several GPa. Experimental conditions for the correct evaluation of Young's modulus were at first identified, choosing a suitable loading rate in order to minimize viscoelastic effects on the unloading. The force curves, i.e., plots of applied load vs. penetration depth, were then analyzed following two common procedures available in the literature. None of these procedures leads to satisfying results when compared to other experimental techniques. Howe…

Rheology of a Lower Critical Solution Temperature Binary Polymer Blend in the Homogeneous, Phase-Separated, and Transitional Regimes

1996

Small amplitude oscillatory shear rheology is employed in order to investigate the linear viscoelastic behavior of the lower critical solution temperature blend polystyrene/poly(vinyl methyl ether), PS/PVME, as a function of temperature and composition. At low temperatures, where the mixture is homogeneous, the dependence of the zero shear viscosity (η0) on concentration is measured and is well-described by means of a new mixing rule, based on surface fractions instead of volume fractions. Shift factors from time-temperature superposition (TTS) exhibit a Williams−Landel−Ferry (WLF) behavior. As the macrophase separation temperature is approached (the phase diagram being established by turbi…

Creep response of a LDPE-based nanocomposite

2016

Polymer nanocomposites and their behavior have been widely investigated by several paths, including mechanical, rheological, and permeability tests, finding that several parameters (such as the polymer matrix, the nanofiller, their amounts, the presence of compatibilizers, processing parameters, etc.) can influence the main properties. However, less information is available regarding the creep response of polymer nanocomposites; in particular, few or no data are reported about the combined effect of different loads and different temperatures. In this article, the creep behavior of a low density polyethylene/organomodified clay nanocomposite has been investigated. The characterization of vis…