Search results for "Viscoplasticity"
showing 10 items of 13 documents
Mechanical properties of natural fiber composites produced using dynamic sheet former
2018
Composites formed from wood fibers and man-made cellulosic fibers in PLA (polylactic acid) matrix, manufactured using sheet forming technique and hot pressing, are studied. The composites have very low density (due to high porosity) and rather good elastic modulus and tensile strength. As expected, these properties for the four types of wood fiber composites studied here improve with increasing weight fraction of fibers, even if porosity is also increasing. On the contrary, for man-made cellulosic fiber composites with circular fiber cross-section, the increasing fiber weight fraction (accompanied by increasing void content) has detrimental effect on stiffness and strength. The differences …
Creep and recovery of epoxy/MWCNT nanocomposites
2012
Abstract Creep and creep–recovery of epoxy/multi-wall carbon nanotube (MWCNT) composites was studied in a wide range of applied loads in order to evaluate the contribution of nanotubes on the time-dependent behaviour of the epoxy matrix. Incorporation of up to 1 wt.% of C150P MWCNTs has negligible influence on the elastic, viscoelastic and viscoplastic response of the epoxy system. No systematic changes of the creep characteristics depending on the content of nanotubes are noticed in the range of stresses from 0.3 up to 0.75 from the ultimate strength. Creep resistance and recovery performance of the epoxy matrix is not negatively affected by the addition of MWCNTs and the same analytical m…
Contributions to the study of the Visco-elastoplastic behavior of a flax fiber – epoxy resin structural composite
2020
The study presented in the manuscript is positioned in a large context of development of new materials, with a reduced environmental impact. From the possibilities currently under scrutiny (especially in Europe), flax fiber reinforced composites are the most promising. Thanks to their low density and high mechanical properties, as well as their low energy costs, fuel the idea of their usage in structural composites, by replacing glass fibers. These biocomposites are already implemented in numerous applications. However, several scientifical and technical unknowns, especially their long-term behavior, are hindering their use in domains of high load conditions.The thesis proposes to study the…
Generalized inverse of the compliance tensor, and behaviour of incompressible anisotropic materials - Application to damage
1997
Before the final rupture, most structural materials exhibit an import damage in the form of microvoids. The overall behaviour of a damaged elastic material depends on the void volume fraction f. Undamaged polymers are generally considered as incompressible elastic. Metals at high temperature may be considered as linearly viscoplastic. Thus the undamaged material may be described by an incompressible behaviour, while the overall behaviour of the damaged material is compressible depending on the void volume fraction. The transition from a compressible to an incompressible behaviour leads to a singular compliance matrix and an undefined rigidity matrix. The generalized inverse of the complianc…
A continuum based fem model for friction stir welding—model development
2006
Although friction stir welding (FSW) has been successfully used to join materials that are difficult-to-weld or unweldeable by fusion welding methods, it is still in its early development stage and, therefore, a scientific knowledge based predictive model is of significant help for thorough understanding of FSW process. In this paper, a continuum based FEM model for friction stir welding process is proposed, that is 3D Lagrangian implicit, coupled, rigid-viscoplastic. This model is calibrated by comparing with experimental results of force and temperature distribution, then is used to investigate the distribution of temperature and strain in heat affect zone and the weld nugget. The model c…
Design of the friction stir welding tool using the continuum based FEM model
2006
In friction stir welding (FSW), the welding tool geometry plays a fundamental role in obtaining desirable microstructures in the weld and the heat-affected zones, and consequently improving strength and fatigue resistance of the joint. In this paper, a FSW process with varying pin geometries (cylindrical and conical) and advancing speeds is numerically modeled, and a thermo-mechanically coupled, rigid-viscoplastic, fully 3D FEM analysis able to predict the process variables as well as the material flow pattern and the grain size in the welded joints is performed. The obtained results allow finding optimal tool geometry and advancing speed for improving nugget integrity of aluminum alloys.
Interface Models for the Analysis of Time-Dependent Effects in Masonry Structures
2001
The present paper is devoted to the theoretical formulation and numerical implementation of an interface model suitable to simulate the behavior of cementitious joints at long term. The interface laws are formulated in the framework of viscoplasticity for non standard materials in order to simulate the time-dependent softening response which occurs along the decohesion process in presence of shear and tension tractions. The interface model parameters identification is discussed on the base of experimental data reported in the literature. The optimization problem related to the parameters evaluation is approached by a heuristic algorithm. Finally some examples show the capabilities of the pr…
Elastic-Viscoplastic Solids Subjected to Thermal and Loading Cycles
1995
— A class of elastic-viscoplastic materials with dual internal variables, thermodynamic potential and temperature-dependent plastic and creep data is considered. For solids (or structures) of such materials, subjected to cyclic loads and temperature variations, the existence of a steady-state response is ascertained and its periodicity characteristics established. Particular steady-state responses, like, elastic and inelastic shakedown, are addressed. By means of a sensitivity analysis of the steady cycle with respect to the load parameter changes, a number of basic features of inelastic shakedown (the viscoplastic counterpart of plastic shakedown) are also addressed.
Friction Stir Welding of steels process design through a continuum based fem model
2009
AbstractFriction stir welding (FSW) has been reaching a continuously increasing popularity among joining processes since its invention in 1991. Although mainly used for aluminium alloys, it has been successfully applied also to steels. In the present paper, a continuum based FEM model for FSW of steels is proposed, which is three-dimensional Lagrangian implicit, coupled, rigid viscoplastic. The model, whose potential has been analysed through temperature distribution comparisons, is able to predict temperature, strain and strain rate distributions, together with thermal and mechanical loads on the welding tool, at varying main process variables. In this way, the FEM model can be used for pr…
Material Flow in FSW of AA7075 - T6 butt joint: numerical simulations and experimental verifications
2006
Friction stir welding (FSW) has reached a large interest in the scientific community and in the recent years also in the industrial environment, owing to the advantages of such solid state welding process with respect to the classic ones. Advanced finite element method tools are needed in order to develop an effective engineering of the processes; quantitative results can be acquired from numerical simulations once the basic information such as the material flow is certain. A 3D Lagrangian implicit coupled rigid viscoplastic model has already been developed by the authors to simulate FSW of butt joints. In the present paper the material flow in the FSW of AA7075–T6 butt joints is investigat…