Search results for "WETTABILITY"
showing 10 items of 25 documents
Graphene and graphene oxide on Ir(111) are transparent to wetting but not to icing
2021
Anti-icing coatings reduce the freezing onset temperature for water by changing the chemical and physical environment at the water-substrate interface to prevent ice nucleation and growth. Graphene oxide has several attributes that make it attractive as an anti-icing coating and it has been theoretically predicted that graphene oxide has a lower freezing onset temperature than pristine graphene. Here, we test this hypothesis using carefully prepared, well-characterized graphene oxide substrates. We compare the water contact angle for graphene and graphene oxide coatings, both prepared on iridium(111) surfaces. The results show both materials to be transparent to wetting, but indicate a lowe…
Wetting ability of an acetone/based etch rinse adhesive after NaOCl-treatment
2011
Objectives: to evaluate the effect of sodium hypochlorite (NaOCl) treatment on surface dentin roughness (Ra) and contact angle (CA) when using Prime&Bond NT adhesive (PB NT). Study Design: Extracted human third molars were sectioned to expose flat, superficial and deep dentin surfaces. CA and Ra were measured (1) before and (2) after 35% H3PO4 etching, and (3) H3PO4 etching + 5% NaOCl treated for 2 minutes before the application of PB NT. CA was measured by the Axisymmetric Drop Shape Analysis Technique using distilled and deionized water and PB NT. Roughness was evaluated with a profilometer, twelve radial measurements were performed in each treatment surface. Data were analyzed with two-w…
Halloysite nanotubes with fluorinated cavity: an innovative consolidant for paper treatment
2016
AbstractHybrid material based on halloysite nanotubes (HNTs) and sodium perfluorooctanoate (NaPF8) was used as a consolidant for paper treatment. The consolidation efficiency was determined by thermogravimetry as well as by paper grammage determination. Morphological analysis of the treated paper was performed by means of scanning electron microscopy while the effect of modified HNTs on the thermal behaviour of the cellulose fibres was investigated by differential scanning calorimetry which determined the combustion enthalpy of the paper.Water contact angle measurements were performed to study the paper wettability. The physico-chemical properties investigated (mesoscopic structure, thermal…
Wettability of flax/basalt reinforced composites during aging in salt spray conditions
2015
Aim of this work was to investigate the wettability of natural fibres reinforced epoxy composites, subjected to aging tests performed on two different laminates. The first laminate was constituted by stacking ten layers of bidirectional flax fabrics. The second one was produced by replacing two external flax layers with two layers of basalt mat, for each side of the laminate. Both laminates were exposed to salt-fog environmental conditions, according to ASTM B 117 standard, for 60 days. The results of wettability were compared with those of the water uptake test. Moreover, an analysis of variance was performed in order to evaluate the significance of the parameters that influence the wettab…
Improvement of the wettability and dissolution of fenofibrate compacts by plasma treatment
2011
Abstract The goal of this study was to investigate the effect of plasma treatment on the wettability and dissolution of fenofibrate compacts. Contact angle measurements and intrinsic dissolution rate studies of untreated and plasma-treated fenofibrate compacts were conducted. The contact angle data clearly show that the wettability of the tablet surface increased with the duration of plasma treatment. Analyses of stability revealed that the surfaces which were plasma-treated for more than 1 min regained some degree of hydrophobicity after storage in air. Since their hydrophobic recovery finally reached the level observed with 1 min plasma-treated fenofibrate compacts it was deduced that per…
Surface AFM microscopy of unworn and worn samples of silicone hydrogel contact lenses
2008
Abstract: Purpose. To evaluate the qualitative and quantitative topographic changes in the surface of worn contact lenses (CLs) of different materials using atomic force microscopy (AFM). Methods. The topography of five different CL materials was evaluated withAFM over a surface of 25 lm2 according to previously published experimental setup. Average roughness (Ra) and root mean square (Rms) values were obtained for unworn and worn samples. Results. The Ra value increased for balafilcon A (11.62–13.68 nm for unworn and worn samples, respectively), lotrafilcon A (3.67–15.01 nm for unworn and worn samples, respectively), lotrafilcon B (4.08–8.42 nm for unworn and worn samples, respectively), g…
First-order and tricritical wetting transitions in the two-dimensional Ising model caused by interfacial pinning at a defect line
2014
We present a study of the critical behavior of the Blume-Capel model with three spin states (S=±1,0) confined between parallel walls separated by a distance L where competitive surface magnetic fields act. By properly choosing the crystal field (D), which regulates the density of nonmagnetic species (S=0), such that those impurities are excluded from the bulk (where D=) except in the middle of the sample [where DM(L/2)≠], we are able to control the presence of a defect line in the middle of the sample and study its influence on the interface between domains of different spin orientations. So essentially we study an Ising model with a defect line but, unlike previous work where defect lines …
Towards Laser-Textured Antibacterial Surfaces
2018
AbstractEscherichia coli and Staphylococcus aureus bacterial retention on mirror-polished and ultrashort pulse laser-textured surfaces is quantified with a new approach based on ISO standards for measurement of antibacterial performance. It is shown that both wettability and surface morphology influence antibacterial behavior, with neither superhydrophobicity nor low surface roughness alone sufficient for reducing initial retention of either tested cell type. Surface structures comprising spikes, laser-induced periodic surface structures (LIPSS) and nano-pillars are produced with 1030 nm wavelength 350 fs laser pulses of energy 19.1 μJ, 1.01 μJ and 1.46 μJ, respectively. SEM analysis, optic…
Evaluation of the surface affinity of water in three biochars using fast field cycling NMR relaxometry
2015
Many soil functions depend on the interaction of water with soil. The affinity of water for soils can be altered by applying soil amendments like stone meal, manure, or biochar (a carbonaceous material obtained by pyrolysis of biomasses). In fact, the addition of hydrophobic biochar to soil may increase soil repellency, reduce water-adsorbing capacity, inhibit microbial activity, alter soil filter, buffer, storage, and transformation functions. For this reason, it is of paramount importance to monitor water affinity for biochar surface (also referred to as 'wettability') in order to better address its applications in soil systems. In this study, we propose the use of fast field cycling NMR …
Effects of Ultraviolet Photoactivation on Osseointegration of Commercial Pure Titanium Dental Implant After 8 Weeks in a Rabbit Model
2020
This study investigated whether a 6-Watt ultraviolet C-lamp was capable of producing photofunctionalization on commercial implants during a medium observation term of 8 weeks. A total of 20 implants were inserted in 5 New Zealand rabbits, with each animal receiving 2 implants per tibia (one photofunctionalized and one untreated), according to a previously established randomization sequence. All implants were inserted by a single surgeon following the manufacturer's instructions. Histological analysis was performed by an evaluator who was blinded to the treatment condition. After 8 weeks of healing, the 2 groups showed no statistically significant differences in terms of bone-to-implant cont…