Search results for "Weibull"
showing 10 items of 57 documents
Empirical model building based on Weibull distribution to describe the joint effect of pH and temperature on the thermal resistance of Bacillus cereu…
2002
Abstract A mathematical model based on Weibull parameters was built to describe the joint effect of temperature and pH on thermal inactivation of Bacillus cereus spores (strain INRA TZ415). The effect of these factors on Weibull model parameters ( β , 1/ α ) was also studied. Heat inactivation tests were carried out in acidified carrot broth as vegetable substrate, following a full factorial design at four levels for temperature (80, 85, 90 and 95 °C) and pH (6.2, 5.8, 5.2 and 4.7). The Weibull distribution model provided good individual fits for the different combinations of temperature–pH tested, with discrepancy factors, D f , coming close to 25% for most cases. The temperature and pH di…
Role of coefficient of thermal expansion on bond strength of ceramic veneered yttrium-stabilized zirconia
2017
Background Incompatible coefficient of thermal expansion (CTE) is supposed to be a reason for chipping of ceramic veneered zirconia. This study evaluates the effect of veneering ceramic at varied CTE on bond strength to zirconia. Material and Methods Zirconia disks (Z, O 10 mm, 1.0 mm thickness) were prepared from Y-TZP (Cercon®) and sintered at 1350°C for 6 hours. All zirconia disks were veneered with ceramics ((O 7.0 mm, 1.5 mm thickness) with varied CTE including VITADur® alpha (VDα), VITAVM®7 (VM7), VITAVM®9 (VM9), Cercon® ceramkiss (CCK), IPSe.max® ceram (IeC), and IPS dSIGN® (IdS) (n=15). The specimens were thermo-cycled (5-55 °C, 500 cycles) prior to determine the shear bond strength…
Effect of different sintering process on flexural strength of translucency monolithic zirconia
2018
Background Sintering process is responsible for the strength of zirconia restoration. This study evaluated the effect of different sintering temperatures and sintered-holding times on flexural strength of translucency monolithic zirconia. Material and Methods One hundred and thirty five zirconia bar specimens (width-length-thickness = 10×20×1.5 mm) were prepared from yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) ceramic and randomly divided into nine groups to be sintered at different temperatures [decreasing- (SD, 1350°C), regular- (SR, 1450°C), and increasing- (SI, 1550°C) sintering temperature] and different sintered-holding times [shortening- (HS, 60 min), regular- (HR, …
Quality of wind speed fitting distributions for the urban area of Palermo, Italy
2011
Abstract This study investigates the wind speed characteristics recorded in the urban area of Palermo, in the south of Italy, by a monitoring network composed by four weather stations. This article has two main objectives: the first one, to describe with clarity and simplicity the numerical procedures adopted to perform a preliminary statistical analysis of wind speed data, providing at the same time, the necessary mathematical tools useful to perform this analysis also without special software. The second objective is to verify if there are more suitable probability distributions able to better represent the original data respect the traditional ones. After a preliminary statistical analys…
Simplified Hybrid PD Model in Voids
2011
In this paper a novel approach to model partial discharges (PD) activity taking place inside a spherical void in epoxy resin system has been traced. The approach is based on a time varying conductance of the inner void, subjected to multistress conditions: voltage, temperature and pressure. A simple lumped circuit macro-model simulates the global effects of PD activity: the different parameters influencing the discharge phenomenon in the void are taking into account by using a physical approach resulting in a time varying conductance inside the circuit. The evaluated PD activity has been compared with experimental and simulated one for the accessible and inaccessible part of the system. A d…
Simplified hybrid PD model in voids: Pattern validation
2013
The purpose of the present work is to show the validation of a new model to simulate the physical phenomenon of partial discharge (PD) produced in air voids inside insulating epoxy resin. The model has been developed on the basis of a new approach that combines the known circuit model of three capacitors with a model used to describe the behavior of the ionized channel inside of the inclusion during the discharge phenomenon, short-circuiting the capacity that represents the void. The approach is based on time-variable conductance of the void, subjected to multistress conditions: voltage, temperature and pressure. The new approach has been developed from a time variable conductivity model us…
Wind speed spatial estimation for energy planning in Sicily: introduction and statistical analysis
2008
Abstract The exploitation of the renewable energy sources plays a key role for achieving the CO 2 emissions reduction targets established by the Kyoto Protocol, as well as for facing the shortage of world fossil fuels reserves. In countries like Italy, with an high potential in terms of wind power generation, an efficient energy planning based on renewables is a very complex task. It encompasses many aspects: the resource availability assessment, the compliance with environmental and legislative constraints and last, but not least, the technical aspects linked to the safe integration to the grid of the intermittent power generated by the wind farms. This paper is the first part of a study a…
Joint probability distributions for wind speed and direction. A case study in Sicily
2015
In this study we analyze data of hourly average wind speed and direction measured at three different sampling stations located in Sicily (Italy) and provide a statistical model for their joint probability density function. Singly truncated from below Normal Weibull mixture distribution and a linear combination of von Mises distributions are used to model wind speed and direction. Sites with heterogeneous local conditions (prevailing wind direction and/or elevation) have been considered in order to investigate the reliability of the model here taken into consideration.
Partial discharge tests using CIGRE method II
2000
In this paper, the results of an experimental project on insulating material aging, performed in both Denmark and Italy, are reported. This study was concerned with partial discharge (PD) behavior at temperatures between 30 and 80/spl deg/C using CIGRE method II. The material tested was a commercial polymethylmethacrylate (PMMA) which was chosen not for its good dielectric properties but rather because much of its discharge resistance data at ambient temperature is already well documented. A description is given of the theoretical and experimental methodology followed in this work. Mixed Weibull analysis techniques in terms of the PD amplitude and phase distribution characteristics were emp…
A new cure model accounting for extra non-cancer mortality: Validation and application to real data
2021
Introduction The proportion of cancer patients cured of the disease is estimated with standard cure models assuming they have the same risk of death as the general population [1] . These patients, however often maintain an extra risk of dying compared to the overall population, which we assume is due to other causes than cancer [2] . The aim of the work was to develop and validate an extended cure model incorporating the estimated patients’ relative risk of death from other causes (α) compared to that observed in the general population. Methods We extended the mixture cure model considering Weibull relative survival of the uncured by including a relative risk αwhich muliptlies the mortality…