Search results for "Wetting"
showing 10 items of 235 documents
Organic matter and wettability characteristics of wildfire ash from Mediterranean conifer forests
2015
Abstract Thermogravimetric analysis (TGA) and water repellency (wettability) determination of ash samples collected following wildfires at four different Mediterranean conifer forest sites in eastern Spain were conducted to provide insights into variations in key chemical and physical characteristics of ash. TGA allowed the evaluation of organic matter (OM) and inorganic carbonate (IC) characteristics and their role in ash wettability. Thermogravimetric profiles were recorded for 40 ash samples (ten from each site). The persistence of water repellency of all ash samples was assessed by the Water Drop Penetration Time (WDPT) test. OM contents decreased, whilst OM stability indices and IC con…
Dung application increases CH4 production potential and alters the composition and abundance of methanogen community in restored peatland soils from …
2018
Peatland restoration via rewetting aims to recover biological communities and biogeochemical processes typical to pristine peatlands. While rewetting promotes recovery of C accumulation favorable for climate mitigation, it also promotes methane (CH4) emissions. The potential for exceptionally high emissions after rewetting has been measured for Central European peatland sites previously grazed by cattle. We addressed the hypothesis that these exceptionally high CH4 emissions result from the previous land use. We analyzed the effects of cattle dung application to peat soils in a short- (2 weeks), a medium- (1 year) and a long-term (grazing) approach. We measured the CH4 production potentials…
Suction controlled drying and wetting cycle effects on the volumetric behaviour of a lime-treated high plasticity clay
2016
The paper presents some experimental results collected on samples recovered from an experimental embankment obtained by compacting a lime-treated clay. Samples were collected soon after the in situ compaction and they were cured in controlled environmental conditions for at least 18 months. Mercury intrusion porosimetry tests (MIP) were carried out on freeze-dried specimens to characterize the microstructure of the material. In order to assess the durability of the improved material, laboratory tests focused on the effects of cyclic variations of the degree of saturation on the water retention properties and the volumetric behaviour of the stabilized clay. Collected results show that the li…
Hydro-mechanical behaviour of a sandy silt from a river embankment
2020
The paper presents the results of an experimental campaign aimed at characterizing the hydro-mechanical behaviour of a sandy silt from a river embankment. Due to continuous river level fluctuations and changing climatic and environmental conditions, flood embankment materials experience frequent variations in degree of saturation and suction values. Such variations strongly impact the earthwork performance both in terms of seepage and stability conditions. For these reasons, a detailed characterization of the material behaviour in unsaturated conditions was carried out. Experiments were designed in order to highlight the response of the involved soil in terms of changes in matric suction an…
Evaluation of a lattice-Boltzmann method for mercury intrusion porosimetry simulations
2004
We have simulated intrusion of a non-wetting liquid into pores of varying shape and size. Simulations were based on the lattice-Boltzmann method and the Shan–Chen multiphase model. The liquid–solid contact angle for pores with circular cross-section was found to be equal to that for pores with square cross-section, and constant even for small pore sizes if the discretised shape of the circular cross-section was taken into account. For comparison, contact angle was also determined for a liquid column descending in a capillary tube, and the results were found to be consistent. Application of the method to mercury intrusion porosimetry is discussed.
Surface modification of poly(ethylene-co-acrylic acid) with amino-functionalized silica nanoparticles
2011
In this work we studied the possibility to achieve a hybrid-surface through the modification, via a facile wet chemical process, of the surface of films of poly(ethylene-co-acrylic acid) (EAA) with amino-modified silica nanoparticles. Films of EAA were preliminarily activated by the introduction of -COCl groups on their surface. Silica nanoparticles were thereafter covalently bound on the polymeric surface as confirmed by FTIR, ATR-FTIR, XPS, NMR and SEM determinations. The nanoparticles formed a multilayer on the film surface and covered almost uniformly the whole film surface. Direct measurements of superficial amino groups by titration allowed us to detect a concentration of about 18 nmo…
The Grain Boundary Wetting Phenomena in the Ti‐Containing High‐Entropy Alloys: A Review
2021
This review is written during the preparation of M‐era.Net full proposal ʺGrain boundaries in multicomponent alloys without principal componentʺ (A.K., A.K., G.A.L. and E.R., application No. 9345). The Institute of Solid State Physics, University of Latvia, as a cen‐ ter of excellence, has received funding from the European Union’s Horizon 2020 Framework Pro‐ gramme H2020‐WIDESPREAD‐01‐2016‐2017‐TeamingPhase2 under grant agreement no. 739508, project CAMART2.
Rayleigh-instability-driven dewetting of thin Au and Ag films on indium-tin-oxide surface under nanosecond laser irradiations
2013
Investigations have been carried out on laser-beam-induced nanoparticle (NP) formation in thin (5 nm) Au and Ag films on indium-tin-oxide substrate. After the irradiation the films were observed to break-up into NPs through a dewetting mechanism. This mechanism was investigated as a Rayleigh-instability- driven process. In fact, for each used laser fluence, the resulting Au and Ag NPs' mean size and surface-to-surface mean distance were quantified and correlated between them in the framework of the Rayleigh-instability theory showing an excellent agreement. © The Institution of Engineering and Technology 2013.
Time resolved emission at 1.3 μm of a single InAs quantum dot by using a tunable fibre Bragg grating
2013
Photoluminescence and time resolved photoluminescence from single metamorphic InAs/GaAs quantum dots (QDs) emitting at 1.3 mu m have been measured by means of a novel fibre-based characterization set-up. We demonstrate that the use of a wavelength tunable fibre Bragg grating filter increases the light collection efficiency by more than one order of magnitude as compared to a conventional grating monochromator. We identified single charged exciton and neutral biexciton transitions in the framework of a random population model. The QD recombination dynamics under pulsed excitation can be understood under the weak quantum confinement potential limit and the interaction between carriers at the …