Search results for "Young's modulus"

Effect of sintering process and additives on the properties of cordierite based ceramics

2013

It is possible to obtain cordierite ceramics with high temperature synthesis using both synthetic and raw natural materials. This paper discusses the possibilities to obtain cordierite ceramics, replacing part of required oxides with raw materials from various Latvian deposits of dolomite and clay. The obtained raw cordierite powders were ground in two modes (3 and 12 hours) and fired at 1200 °C. Ceramic samples were characterized by hydrostatic weighting method; crystalline phase composition was studied by XRD. Obtained samples were evaluated by their mechanical (compressive) strength and linear coefficient of thermal expansion (CTE). Thermal shock resistance was tested using water quenchi…

Real-time manipulation of ZnO nanowires on a flat surface employed for tribological measurements: Experimental methods and modeling

2012

Elastic and tribological properties of zinc oxide nanowires (NWs) on Si wafer and highly oriented pyrolytic graphite (HOPG) are experimentally investigated and theoretically interpreted. Measurements are performed inside a scanning electron microscope (SEM) using real-time manipulation technique that enables two possible ways of data registration: “external” force registration with quartz tuning fork (QTF) based sensor and “internal” force registration utilizing in situ observed elastic deformation of NWs. Young modulus is determined by loading half-suspended NW at its free end and then employed for the following tribological experiments. Maximal static friction force is estimated when NW i…

Increasing the elastic modulus of polyamides

1977

STRONTIUM CONCENTRATION DEPENDENCE OF SELECTED STRUCTURAL AND MECHANICAL PROPERTIES OF POLYCRYSTALLINE Ba1−XSrXTiO3

2009

ABSTRACT Microstructure and material constants such as Young modulus E, shear modulus G, Poisson ratioν of polycrystalline ferroelectric materials Ba1-xSrxTiO3 for 0≤x≤0.4 were investigated to determine their dependence on strontium concentration. The performed investigations showed that the material is chemically homogeneous. It was found that the strontium concentration had no significant influence on the grain size. The highest value of Young's modulus is observed for Ba0.6Sr0.4TiO3 sample. The performed investigations of mechanical properties made it possible to evaluate the usability of this material for manufacturing transducers and sensors which could work under load.

Architecture in cortical bone and ultrasound transmission velocity

1993

The square of ultrasound transmission velocity in a material is correlated to the modulus of elasticity, which is an indicator of its mechanical properties. This might make the measurement of ultrasound transmission velocity useful in the noninvasive diagnosis of bone diseases. Bone, however, is not an isotropic material but is architecturally structured. The aim of our study was to investigate and especially to quantify the influence of architecture in cortical bone on ultrasound transmission velocity. Twenty-two rectangular, flat specimens of cortical bone were prepared from diaphysis of fresh pig radius. Ultrasound transmission velocity was measured parallel and perpendicular to directio…

Size Distribution, Mechanical and Electrical Properties of CuO Nanowires Grown by Modified Thermal Oxidation Methods

2020

Size distribution, Young&rsquo

The role of micro-structural and mechanical properties in the framework of the model for damage inception and growth from air-filled voids in Polyeth…

2007

An innovative, physical, aging and life model for polymeric insulation systems, founded on damage inception and growth at the level of microscopic cavities, was developed previously by the authors. This paper is focused on the role played by micro-structural and mechanical properties (such as crystallinity and Young's modulus) in the framework of such model. These concepts are applied to the case of LDPE, HDPE and XLPE matrixes. The relevant estimates of damage growth rate and time-to-failure as a function of void size and applied electric field in typical working conditions for HVDC power cables are performed. The results show that, under the assumptions made, the crystallinity level itsel…

Reinforcement Efficiency of Cellulose Microfibers for the Tensile Stiffness and Strength of Rigid Low-Density Polyurethane Foams

2020

Rigid low-density closed-cell polyurethane (PU) foams are widely used in both thermal insulation and structural applications. The sustainability of PU foam production can be increased by using bio-based components and fillers that ensure both enhanced mechanical properties and higher renewable material content. Such bio-based foams were produced using polyols derived from rapeseed oil and microcrystalline cellulose (MCC) fibers as filler. The effect of MCC fiber loading of up to 10 wt % on the morphology, tensile stiffness, and strength of foams has been evaluated. For estimation of the mechanical reinforcement efficiency of foams, a model allowing for the partial alignment of filler fibers…

Accurately evaluating Young’s modulus of polymers through nanoindentations: a phenomenological correction factor to the Oliver and Pharr procedure

2006

The Oliver and Pharr [J. Mater. Res. 7, 1564 (1992)] procedure is a widely used tool to analyze nanoindentation force curves obtained on metals or ceramics. Its application to polymers is, however, difficult, as Young’s moduli are commonly overestimated mainly because of viscoelastic effects and pileup. However, polymers spanning a large range of morphologies have been used in this work to introduce a phenomenological correction factor. It depends on indenter geometry: sets of calibration indentations have to be performed on some polymers with known elastic moduli to characterize each indenter.

On the Use of the Nanoindentation Unloading Curve to Measure the Young's Modulus of Polymers on a Nanometer Scale

2005

Summary: The nanoindentation test is a fundamental tool to assess the link between morphology and mechanical properties. The preliminary results of a more exhaustive study about the applicability to polymers of the most used procedure to determine elastic modulus by indentation are reported in this short communication. A departure of the experimental conditions from the theoretical assumptions and results that give rise to the Oliver and Pharr analysis is shown to occur under a wide range of experimental conditions, with applied loads and penetration depths covering several orders of magnitude and using different indenter geometries. Unloading curves with exponents significantly larger than…