Search results for "aluminium"
showing 10 items of 548 documents
The application of the random balance method in laser machining of metals
2008
International audience; Features peculiar to laser technology offer some advantages over more traditional processes, but, like all processes, it has its limitations. This article studies the limitations of laser machining of metals, and quantifies, through an experimental design method, the influence of operating parameters on productivity and on the quality of the machined surface. Three study materials were used: an aluminium alloy, stainless steel and a titanium alloy. An initial reading of the results indicates that productivity depends mainly on the frequency of the laser pulse and that the aluminium alloy behaves differently from the other two. The quality of the machined surface, jud…
Influence of processing parameters and initial temper on Friction Stir Extrusion of 2050 aluminum alloy
2017
Abstract Friction Stir Extrusion is an innovative production technology that enables direct wire production via consolidation and extrusion of metal chips or solid billets. During the process, a rotating die is plunged into a cylindrical chamber containing the material to be extruded. The stirring action of the tool produces plastic flow in the extrusion chamber, densifying and heating the charge so that finally, fully dense rods are extruded. Experiments have been carried out in order to investigate the influence of process parameters and initial temper of the base material on the process variables and on the extrudates’ mechanical properties.
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
Linear friction welding of dissimilar AA6082 and AA2011 aluminum alloys: microstructural characterization and design guidelines
2015
This paper presents the results of an experimental and numerical campaign on Linear Friction Welding of dissimilar AA2011-T8 and AA6082-T6 aluminum alloys. Experimental tests were carried out with constant oscillation amplitude and process time. Varying oscillation frequency, interface pressure, specimen geometry and mutual position were used. Grain size measurements, HV tests and EDX analysis were considered to characterize the microstructure of the joints as a function of the input process parameters. A thermal numerical model was utilized to predict the temperature profiles in the joints during the process. The obtained results allowed the identification of four weld categories: sound jo…
Friction stir extrusion to recycle aluminum alloys scraps: Energy efficiency characterization
2019
Abstract Solid state recycling refers to a group of processes allowing direct recycling of metals scraps into semi-finished product. Their main advantage lies in avoiding the molten state of the material which badly affects the environmental performance of the conventional (remelting based) recycling routes. It is expected that such process category would lower the environmental performance of metals recycling. In this paper, the friction stir extrusion process for aluminum alloy AA 2050 wire production is analyzed under the primary energy demand perspective. The process electrical energy demand is quantified with varying process parameters. An empirical modelling approach was applied and a…
Uncovering Technological and Environmental Potentials of Aluminum Alloy Scraps Recycling Through Friction Stir Consolidation
2020
Conventional metal chips recycling processes are energy-intensive with low efficiency and permanent material losses during re-melting. Solid state recycling allows direct recycling of metal scraps into semi-finished products. It is expected that this process category would lower the environmental performance of metals recycling. Friction Stir Consolidation is a new solid-state technique taking advantage of friction heat generation and severe plastic deformation to consolidate chips into billets. In this research, the feasibility of Friction Stir Consolidation as aluminum chips recycling process is analyzed. Specifically, an experimental campaign has been carried out with varying main proces…
Al-SiC Metal Matrix Composite production through Friction Stir Extrusion of aluminum chips
2017
Abstract The production of most mechanical component requires machining operation, thus usually implying the cut material to be wasted as scrap. Traditional recycling techniques are not able to efficiently recycle metal chips because of some critical aspects that characterize such kind of scraps (shape, oxide layers, contaminating residues, etc). Friction Stir Extrusion is an innovative solid state direct-recycling technique for metal machining chips. During the process, a rotating tool is plunged into a hollows matrix to compact, stir and finally, back extrudes the chips to be recycled in a full dense rod. This process results to be particularly relevant since no preliminary treatment of t…
Application of linear friction welding for joining ultrafine grained aluminium
2020
Abstract Ultrafine grained (UFG) materials are of great potential in industry due to their enhanced mechanical strength and other promising features, such as ability to superplastic deformation or excellent corrosion resistance. Nevertheless, one of the main limitations lies in their low thermal stability, which leads to excessive grain growth at elevated temperature. It influences mainly further processes performed at high temperature, such as joining. It causes detrimental problems during conventional fusion welding, as significant grain growth is observed and therefore the advantages as a result of small average grain size disappear. Therefore, the idea of applying solid state joining pr…
Aluminium sheet metal scrap recycling through friction consolidation
2019
Abstract In the last decades, several direct-recycling techniques have been developed and investigated in order to avoid material remelting, typical of the conventional aluminum alloys recycling processes. Moreover, the remelting step for aluminum recycling is affected by permanent material losses. Solid-state recycling processes have proven to be a suitable strategy to face such issues. Friction Consolidation is an innovative solid state-recycling technology developed for metal chips. During the process, a rotating die is plunged into a hollow chamber containing the material to be processed. The work of friction forces decaying into heat soften the material and, together with the stirring …
An energy efficiency analysis of Single Point Incremental Forming as an Approach for Sheet Metal Based Component Reuse
2020
Abstract Producing materials causes about 25% of all anthropogenic CO2 emissions. Metals play a significant role, steel and aluminum account for 24% and 3% of worldwide material related emissions respectively. Fostering resources efficiency strategies in the field of sheet components could lead to a significant environmental impact reduction. Reshaping could be one of the most efficient strategy to foster material reuse and lower the environmental impact due to material production. Specifically, for aluminum recycling, the overall energy efficiency of conventional route is very low and, more importantly, permanent material losses occur during re-melting because of oxidation. The present pap…