Search results for "anodic"

The passivation of steel in sodium sulphate solution studied by CEMS and aes

1990

The passive layer formed on standard steel by anodic oxidation in 0.5 M sodium sulphate solution was found to contain iron only in the trivalent state. The thickness of the layer increases with the applied potential as well as with the time the passivating potential is applied to the sample. These results, compared with the electrochemical data, lead to the suggestion that the passive behaviour is not due to the whole oxidic layer but due to a thin, low lying interfacial layer with a structural disorder.

Growth of passive layers on nickel during their voltammetric anodic dissolution in a weakly acid medium

2006

Abstract Quartz crystal microbalance in combination with voltammetry has been used for studying the electrochemical oxidation behaviour of a nickel deposit in a weakly acid medium. The instantaneous mass/charge ratio (Fdm/dQ) analysis allows to obtain the fraction of charge consumed in the passivation process, and, that way, the experimental kinetic equation of the passive layer growth. This experimental law has been fitted to the theoretical equation derived from the point defect model theory under voltammetric conditions.

Structural and Photocurrent Characterization of Anodic Oxides on Titanium

2010

The Influence of Thermal Treatment on the Electronic Properties of a-Nb2O5

2009

The effect of thermal treatments for 1h at 250{degree sign}C in air or under vacuum on the electronic structure of thick amorphous anodic niobia was characterized by electrochemical impedance, differential admittance (DA) and photocurrent spectroscopy (PCS). The analysis of anodized niobia has revealed that it behaves as a pure dielectric. The thermal treatment in air increases the value of the differential capacitance of the niobia sample. The effect is stronger when the thermal treatment is carried out in vacuum and can be cancelled out by reanodizing the oxide to the initial formation potential. In the case of thermally vacuum-treated sample, a behavior typical of semiconducting amorphou…

The influence of nitrogen incorporation on the optical properties of anodic Ta2O5

2012

Abstract Anodic oxides were grown on sputter-deposited Ta in different aqueous solutions. A photoelectrochemical investigation was performed in order to estimate the band gap of the films as a function of the anodizing bath composition and formation voltage, i.e. thickness. Photoelectrochemical results provided evidence of sub-band gap photocurrent for films formed in a bath containing ammonium ions at pH 9. Elemental depth profiles obtained by glow discharge optical emission spectroscopy revealed the presence of nitrogen species in the outer part of the anodic films, which is bonded to Ta according to XPS analysis. A mechanism of nitrogen incorporation is proposed in order to account for t…

The influence of surface treatment on the anodizing of magnesium in alkaline solution

2011

Abstract The mechanism of magnesium anodizing after mechanical polishing or HF pickling was studied. X-ray Photoelectron Spectroscopy and Photocurrent Spectroscopy were employed to characterize both the initial films formed on Mg soon after surface treatments and the anodic films grown in strongly alkaline solutions. Electrochemical and capacitance measurements were performed in order to study the oxidation process and to check if the kinetic of growth fits the Mott–Cabrera high field model. From Tafel plots it was possible to estimate the activation distance, while the simulation of the barrier layer growth as a function of the potential at high scan rate allowed to estimate the other kine…

The effect of thickness on the composition of passive films on a Ti–50Zr at% alloy

2006

Abstract Anodic films were grown potentiodynamically in different electrolytes (pH = 1–14) on a Ti–50Zr at% cast alloy, obtained by fusion in a voltaic arc under argon atmosphere. The thickness of the films was varied by changing formation potential from the open circuit potential up to about 9 V; growth was followed by 30 min stabilization at the forming potential. Films having different thicknesses were characterized by photocurrent spectroscopy (PCS) and electrochemical impedance spectroscopy (EIS). Moreover, film composition was analyzed by X-ray photoelectron spectroscopy (XPS). Regardless of the anodizing conditions, passive films on the Ti–50Zr at% alloy consist of a single layer mix…

Photoelectrochemical characterization of amorphous anodic films on Ti-6at.%Si

2013

Abstract The solid state properties of anodic films grown galvanostatically on sputtering-deposited Ti–6at.%Si alloys were studied as a function of the formation voltage (5–40 V). From the photocurrent spectra a band gap of ∼3.4 eV was estimated for all the investigated thicknesses, which is almost coincident with the value measured for amorphous TiO 2 . The photocharacteristics allowed to estimate the flat band potential of the films, which resulted to be more anodic for thicker layers and allowed to evidence a change from n-type semiconducting material to insulator by increasing the formation voltage. A dielectric constant of ∼31 was estimated by differential capacitance measurements. The…

Photocurrent Spectroscopy Applied to the Characterization of Passive Films on Sputter-Deposited Ti-Zr Alloys

2008

Abstract A photoelectrochemical investigation on thin (⩽13 nm) mixed oxides grown on sputter-deposited Ti–Zr alloys of different composition by air exposure and by anodizing (formation voltage, UF = 4 V/SCE) was carried out. The experimental results showed that the optical band gap, E g opt , increases with increasing Zr content in both air formed and anodic films. Such behaviour is in agreement with the theoretical expectation based on the correlation between the band gap values of oxides and the difference of electronegativity of their constituents. The flat band potential of the mixed oxides was found to be almost independent on the Ti/Zr ratio into the film and more anodic with respect …

Physicochemical characterisation of thermally aged anodic films on magnetron sputtered niobium

2010

The influence of thermal aging, at intermediate temperature (1h at 250°C) and in different environments, on the electronic and solid-state properties of stabilized 160 nm thick amorphous anodic niobia, grown on magnetron sputtered niobium metal, has been studied. A detailed physicochemical characterisation of the a-Nb2O5/0.5M H2SO4 electrolyte junction has been carried out by means of photocurrent and electrochemical impedance spectroscopy as well by differential admittance measurements. A change in the optical band gap (3.45 eV) of niobia film has been observed after aging (3.30 eV) at 250°C in air for 1 hour. A cathodic shift (0.15-0.2 Volt) in the flat band potential of the junction has …