Search results for "atomic force"

2019

Atomic force microscopy (AFM) is today an established tool in imaging and determination of mechanical properties of biomaterials. Due to their complex organization, those materials show intricate properties such as viscoelasticity. Therefore, one has to consider that the loading rate at which the sample is probed will lead to different mechanical response (properties). In this work, we studied the dependence of the mechanical properties of endothelial cells on the loading rate using AFM in force spectroscopy mode. We employed a sharp, four-sided pyramidal indenter and loading rates ranging from 0.5 to 20 μm/s. In addition, by variation of the load (applied forces from 100 to 10,000 pN), the…

Measuring (biological) materials mechanics with atomic force microscopy. 2. Influence of the loading rate and applied force (colloidal particles)

2020

Atomic force microscopy (AFM) is the most often used tool to study the mechanical properties of eukaryotic cells. Due to their complex assembly, cells show viscoelastic properties. When performing experiments, one has to consider the influence of both loading rate and maximum load on the measured mechanical properties. Here, we employed colloidal particles of various sizes (from 2 to 20 μm diameter) to perform force spectroscopy measurements on endothelial cells at loading rates varying from 0.1 to 50 μm/s, and maximum loads ranging from 1 to 25 nN. We were able to determine the non-linear dependence of cell viscoelastic properties on the loading rate which followed a weak power law. In add…

Scanning probe microscopies applied to the study of the domain wall in a ferroelectric crystal.

2007

Summary Scanning near-field optical microscopy is capable of measuring the topography and optical signals at the same time. This fact makes this technique a valuable tool in the study of materials at nanometric scale and, in particular, of ferroelectric materials, as it permits the study of their domains structure without the need of chemical etching and, therefore, not damaging the surface (as will be demonstrated later). We have measured the scanning near-field optical microscopy transmission, as well as the topography, of an RbTiOPO4 single crystalline slab, which exhibits two different of macroscopic ferroelectric domains. A chemical selective etching has been performed to distinguish b…

Anomalous behaviour of periodic domain structure in Gd-doped LiNbO3single crystals

2007

Atomic force microscopy studies of etching patterns, stability of regular domain structure, and anomalies of electrical characteristics in the 300 - 385 K range of a series of Gddoped lithium niobate single crystals grown under equal conditions are reported.

Current injection from metal to MoS2 probed at nanoscale by conductive atomic force microscopy

2016

Contacts with MoS2 are currently the object of many investigations, since current injection through metal/MoS2 interfaces represents one of the limiting factors to the performance of MoS2 thin film transistors. In this paper, we employed conductive atomic force microscopy (CAFM) to investigate the current injection mechanisms from a nanometric contact (a Pt coated tip) to the surface of MoS2 thin films exfoliated on SiO2. The analysis of local current-voltage (I-V) characteristics on a large array of tip positions provided high spatial resolution information on the lateral homogeneity of the tip/MoS2 Schottky barrier Phi(B) and of the ideality factor n. From the histograms of the measured P…

Self-Organization Pathways and Spatial Heterogeneity in Insulin Amyloid Fibril Formation

2009

At high temperature and low pH, the protein hormone insulin is highly prone to form amyloid fibrils, and for this reason it is widely used as a model system to study fibril formation mechanisms. In this work, we focused on insulin aggregation mechanisms occurring in HCl solutions (pH 1.6) at 60 degrees C. By means of in situ Thioflavin T (ThT) staining, the kinetics profiles were characterized as a function of the protein concentration, and two concurrent aggregation pathways were pointed out, being concentration dependent. In correspondence to these pathways, different morphologies of self-assembled protein molecules were detected by atomic force microscopy images also evidencing the prese…

Elasticity and yield strength of pentagonal silver nanowires: In situ bending tests

2014

This paper reports in situ mechanical characterization of silver nanowires (Ag NWs) inside a scanning electron microscope using a cantilevered beam bending technique. Measurements consisted in controlled bending of a cantilevered NW by the tip of an atomic force microscope glued to the force sensor. Relatively high degree of elasticity followed by either plastic deformation or fracture was observed in bending experiments. Experimental data were numerically fitted into the model based on the elastic beam theory and values of Young modulus and yield strength were extracted. Measurements were performed on twenty Ag NWs with diameters from 76 nm to 211 nm. Average Young modulus and yield streng…

Affinity scale between a carrier and a drug in DPI studied by atomic force microscopy.

2002

The dry powder inhalers (DPIs) consist, in the most cases, of ordered mixture where the particles adhesion results of interactions between the drug and the carrier. Generally, one step of production process is the micronization of the drug particles in order to reduce the size for ordered mixing optimization. But this operation is known to partially create an amorphous surface. In this case, surrounding storage conditions, like relative humidity (RH), are able to modify the percentage of amorphous drug surface. The aim of this study was to investigate surface reactivity, surface energy and direct force measurements by atomic force microscopy (AFM) between lactose (carrier) and zanamivir (dr…

Tribological Aspects of In Situ Manipulation of Nanostructures Inside Scanning Electron Microscope

2014

This chapter is dedicated to manipulation of nanostructures inside a scanning electron (SEM) microscope employed for real-time tribological measurements. Different approaches to force registration and calculation of static and kinetic friction are described. Application of the considered methodology to Au and Ag nanoparticles, as well as ZnO and CuO nanowires, is demonstrated. Advantages and limitations of the methodology in comparison to traditional AFM-based manipulation techniques are discussed.

In-Situ atomic force microscopic observation of ion beam bombarded plant cell envelopes

2007

Abstract A program in ion beam bioengineering has been established at Chiang Mai University (CMU), Thailand, and ion beam induced transfer of plasmid DNA molecules into bacterial cells (Escherichia coli) has been demonstrated. However, a good understanding of the fundamental physical processes involved is lacking. In parallel work, onion skin cells have been bombarded with Ar+ ions at energy 25 keV and fluence1–2 × 1015 ions/cm2, revealing the formation of microcrater-like structures on the cell wall that could serve as channels for the transfer of large macromolecules into the cell interior. An in-situ atomic force microscope (AFM) system has been designed and installed in the CMU bio-impl…