Search results for "automatic"

Increasing the VoIP Capacity through MAP Overhead Reduction in the IEEE 802.16 OFDMa Systems

2010

One of the main issues with supporting VoIP service over 802.16 networks is the signalling overhead caused by the downlink MAP messages due to frequent transmissions and small packets. To decrease the MAP overhead, the 802.16 standard proposes some mechanisms, such as the compressed MAP and sub-MAPs. In this paper, we show by means of extensive dynamic simulations that sub-MAPs can reduce dramatically the signalling overhead associated with VoIP traffic and significantly improve overall VoIP capacity. At the same time, since sub-MAPs are more sensitive to packet drops, they tend to increase the number of HARQ retransmissions in downlink and transmission delays in the uplink direction.

Analysis of the Non-Transparent In-Band Relays in the IEEE 802.16 Multi-Hop System

2010

This paper presents extensive dynamic simulations of the non-transparent in-band relays working in the distributed scheduling mode. The simulation results show that in-band relays can improve noticeably the spectral efficiency without acquiring an additional radio spectrum. Also, packet transmission delays become smaller. An important outcome of the dynamic simulations is that it is very crucial to choose a correct relay zone size where the base station and relay nodes exchange data. Otherwise, throughput fairness of the whole system declines. It indicates an importance of the relay zone size adjustment algorithm that the base station must run.

ARQ parameters for VoIP in IEEE 802.16 networks

2009

IEEE 802.16 standard defines two data retransmission mechanisms. HARQ provides fast retransmissions in cost of slightly increased overhead. On the contrary, ARQ has less overhead in cost of bit longer delays. It is therefore often used with BE connections. In addition to delay tolerant applications, BE can also be used for real-time services. Therefore, in this paper we analyze the ARQ mechanism and provide guidelines on how to set the ARQ parameters to achieve a good balance between the VoIP delay and packet loss.

Impact of portable device restrictions on IEEE 802.16 performance

2008

IEEE 802.16 is a good alternative for fast wireless connection in the next generation portable information devices (PID). However it was not originally designed for portable devices, but mobility was added later to the specification. This means that the lack of resources on portable devices might have a significant impact on which IEEE 802.16 features should be chosen and how they should be used. Proper usage of ARQ can increase the IEEE 802.16 performance but it can also require much resources from PIDs. In this paper we focus on how ARQ features are affected by limited resources on PID and how much the limitations affect on the performance.

Model-based automatic tuning of a filtration control system for submerged anaerobic membrane bioreactors (AnMBR)

2014

This paper describes a model-based method to optimise filtration in submerged AnMBRs. The method is applied to an advanced knowledge-based control system and considers three statistical methods: (1) sensitivity analysis (Morris screening method) to identify an input subset for the advanced controller; (2) Monte Carlo method (trajectory-based random sampling) to find suitable initial values for the control inputs; and (3) optimisation algorithm (performing as a supervisory controller) to re-calibrate these control inputs in order to minimise plant operating costs. The model-based supervisory controller proposed allowed filtration to be optimised with low computational demands (about 5min). E…

A Saturation Model of the Synchronous Reluctance Motor and its Identification by Genetic Algorithms

2018

This paper proposes a complete saturation model of the Synchronous Reluctance Motor (Syn1231), accounting for both the self-saturation and cross-saturation effects. This model is based on an analytical relationship between the stator flux and current components, and is characterized by parameters presenting an interesting physical interpretation, differently from many other saturation model in the scientific literature. It proposes also an identification technique of such a model based on stand-still tests, without the need of locking the rotor. The proposed saturation model permits the complete description of the magnetic behaviour of the machine with 8 parameters, fewer than those require…

Identification and validation of quasispecies models for biological systems

2009

An identification procedure for biological systems cast as quasi-species models is proposed. Their identification is a challenging problem because of the bilinear dependence on the parameters and their physical constraints. The proposed solution is within the framework of set-membership identification. %The bilinear dependence on parameters of the model and their physical constraints make the present issue challenging. We determine an estimate of the model parameters together with their interval of variability (Uncertainty Intervals), taking into account all the physical constraints. Invalidation/validation is performed on the basis of the predictive capability of the estimated models. The …

Hybrid LPV Modeling and Identi cation

2011

Introduction to the Issue on Advances in Remote Sensing Image Processing

2011

The papers in this special issue span a wide range of problems arising in modern remote sensing data analysis and provide a snapshot in the state-of-the-art of remote sensing image processing. More advances are expected in the near future, mainly due to the increasing user demands in terms of spatial, spectral, and temporal resolutions of data, and of products generated from these data by automatic processing techniques.

Visual Servoing Based on Shifted Moments

2015

Over the past decade, image moments have been exploited in several visual servoing schemes for their ability to represent object regions, objects defined by contours or a set of discrete points. Moments have also been useful to achieve control decoupling properties and to choose a minimal number of features to control the whole degrees of freedom (DOFs) of a camera. However, the choice of moment-based features to control the rotational motions around the $x$ -axis and $y$ -axis simultaneously with the translational motions along the same axis remains a key issue. In this paper, we introduce new visual features computed from low-order “shifted moments invariant.” Importantly, they allow us 1…