Search results for "automatic"
showing 10 items of 730 documents
A discrete pulse group control-based series resonant inverter with complete ZCS-assisted inductors for consumer high frequency IH application
2017
This paper presents a pulse density modulated (PDM) voltage source high frequency series load resonant soft switching inverter (SRI) for the HF induction heated fixing roller in the energy saving copy and printing machines. The proposed simple and high efficiency SRI based on PDM control operation can achieve complete zero current soft switching for wide output power regulation ranges. In this work, its transient and steady-state operating principle are described and analyzed on the basis of high frequency PDM. The operating performances as power conversion efficiency, power losses analysis and temperature rising characteristics of this SRI are demonstrated and discussed through experimenta…
Reconstitution of a protein monolayer on thiolates functionalized gaas surface
2012
International audience; In the aim to realize an efficient resonant biosensor, gallium arsenide (GaAs) presents many advantages. In addition to its properties of transduction, GaAs is a crystal for which microfabrication processes were developed, conferring the possibility to miniaturize the device and integrate electronic circuit. Moreover, the biofunctionalization could be realized on the crystalline surface without layer deposition, constituting a real advantage to perform reusable sensor. The functionalization of GaAs surface was engaged in order to immobilize a protein monolayer on this substrate. Functionalization was done using a mixed self assembled monolayer of thiolate molecules. …
Design and experimental validation of a high voltage ratio DC/DC converter for proton exchange membrane electrolyzer applications
2019
Abstract This paper deals with hydrogen production via water electrolysis, which is considered the most attractive and promising solution. Specifically, the use of renewable energy sources, such as wind electric power generators, is hypothesized for supplying the electrolyzer, aiming to strongly reduce the environmental impact. In particular, micro-wind energy conversion systems (μWECSs) are attractive for their low cost and easy installation. In order to interface the μWECS and the electrolyzer, suitable power conditioning systems such as step-down DC-DC converters are mandatory. However, due to the requested high conversion ratio between the DC bus grid, i.e. the output of a three-phase d…
A Magnetostrictive Electric Power Generator for energy harvesting from traffic: Design and experimental verification
2015
In the last decades, the growth in energy demand, the decrease of fossil fuels available in the market and the impact of anthropogenic factors on climate change has given new impulse to research on renewable energy systems, particularly those known as energy harvesting devices (EHDs) [1]. A large number of EHDs have been proposed, using different operating principle [1-4]. Among them, piezoelectric and magnetostrictive seem to be particularly suitable for the application in EHD. In these materials the application of external mechanical stress induces a change in the level of magnetization and therefore an electromotive force (emf) can be generated and collected in order to produce electrica…
Microstructure-oxidation resistance relationship in Ti3AlC2 MAX phase
2020
International audience; Spark Plasma Sintering and Hot Isostatic Pressing were used to synthesize coarse-grained and fine-grained Ti3AlC2 specimens. Moreover, Spark Plasma Sintering processing parameters were modified in order to vary the TiC, Al2O3 and TixAly impurity and the porosity contents in the fine-grained samples. The influence of the Ti3AlC2 microstructure on the oxidation resistance was assesed. It is demonstrated that the grain size can drastically modify the oxidation resistance. The higher density of grain boundaries, in fine-grained specimens, increases the number of Al diffusion paths and leads to the formation of a protective alumina scale. In coarse-grained sample, Al diff…
Study and design of a controlled oscillator for an embedded system to measure the complex impedance of PEM fuel cell »
2017
We present in this paper the study and the design of a voltage controlled oscillator (VCO) for an embedded system to diagnose the PEM fuel cell. Some problems related to fuel cells used in the electric vehicle field are the management of its efficiency and the lifetime of its membranes. To do this, the diagnosis using measuring the complex impedance is an important phase. It is based on the injection of a perturbation signal at the output of the PEM fuel cell, then we observe its behavior by measuring its impedance. The used measurement method is the electrochemical impedance spectroscopy (EIS) using the load modulation technique, which is implemented in an embedded measurement system based…
Approximation of the Feasible Parameter Set in worst-case identification of Hammerstein models
2005
The estimation of the Feasible Parameter Set (FPS) for Hammerstein models in a worst-case setting is considered. A bounding procedure is determined both for polytopic and ellipsoidic uncertainties. It consists in the projection of the FPS of the extended parameter vector onto suitable subspaces and in the solution of convex optimization problems which provide Uncertainties Intervals of the model parameters. The bounds obtained are tighter than in the previous approaches. hes.
On the Distance-Constrained Close Enough Arc Routing Problem
2021
[EN] Arc routing problems consist basically of finding one or several routes traversing a given set of arcs and/or edges that must be serviced. The Close-Enough Arc Routing Problem, or Generalized Directed Rural Postman Problem, does not assume that customers are located at specific arcs, but can be serviced by traversing any arc of a given subset. Real-life applications include routing for meter reading, in which a vehicle equipped with a receiver travels a street network. If the vehicle gets within a certain distance of a meter, the receiver collects its data. Therefore, only a few streets which are close enough to the meters need to be traversed. In this paper we study the generalization…
Robust control of uncertain multi-inventory systems via linear matrix inequality
2008
We consider a continuous time linear multi inventory system with unknown demands bounded within ellipsoids and controls bounded within ellipsoids or polytopes. We address the problem of "-stabilizing the inventory since this implies some reduction of the inventory costs. The main results are certain conditions under which "-stabilizability is possible through a saturated linear state feedback control. All the results are based on a Linear Matrix Inequalities (LMIs) approach and on some recent techniques for the modeling and analysis of polytopic systems with saturations.
MCR-ALS on metabolic networks: Obtaining more meaningful pathways
2015
[EN] With the aim of understanding the flux distributions across a metabolic network, i.e. within living cells, Principal Component Analysis (PCA) has been proposed to obtain a set of orthogonal components (pathways) capturing most of the variance in the flux data. The problems with this method are (i) that no additional information can be included in the model, and (ii) that orthogonality imposes a hard constraint, not always reasonably. To overcome these drawbacks, here we propose to use a more flexible approach such as Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) to obtain this set of biological pathways through the network. By using this method, different constraint…