Search results for "back"
showing 10 items of 2078 documents
A new procedure to determine the rheological properties of RAP binder and corresponding bituminous blends
2017
Abstract In this paper, a new and simple approach to estimate the rheological properties of Reclaimed Asphalt Pavement (RAP) binder is proposed to overcome the limitations of the conventional extraction procedure. This method is based on Dynamic Shear Rheometer tests performed on mortars composed of RAP fine fraction and virgin binder, together with a new back-calculation solution. The properties of the bituminous blends of virgin and RAP binders are obtained with a modified Nielsen model. The Voigt model is then successfully used to estimate complex modulus and phase angle of the RAP binder from the properties of the back-calculated binder blend. This procedure would prevent the need of RA…
Highly textured Gd2Zr2O7 films grown on textured Ni-5at.%W substrates by solution deposition route: Growth, texture evolution, and microstructure dep…
2012
Abstract Growth, texture evolution and microstructure dependency of solution derived Gd 2 Zr 2 O 7 films deposited on textured Ni-5 at.%W substrates have been extensively studied. Influence of processing parameters, in particular annealing temperature and dwell time, as well as thickness effect on film texture and morphology are investigated in details. It is found that a rotated cube-on-cube epitaxy of Gd 2 Zr 2 O 7 //NiW in-plane texture forms as soon as the (004) out-plane texture appears, implying that epitaxial growth dominates the crystallization processes. Thermal energy plays an important role in minimizing the difference of interfacial energy along two directions in the anisotropic…
A Brief Review on the Resistance-in-Series Model in Membrane Bioreactors (MBRs)
2019
The cake layer deposited on the membrane modules of membrane bioreactors (MBRs), especially under a submerged configuration, represents a relevant and fundamental mechanism deeply influencing the development of membrane fouling. It negatively affects the total resistance to filtration, while exerting a positive effect as a “pre-filter„ promoting the “dynamic membrane„ that protects the physical membrane from internal fouling. These two opposite phenomena should be properly managed, where the submerged membranes are usually subjected to a periodical cake layer removal through ordinary (permeate backwashing and air scouring) and/or irregular cleaning actions (manual ph…
Atomic layer deposition of Ti-Nb-O thin films onto electrospun fibers for fibrous and tubular catalyst support structures
2018
Here, the authors report on the preparation of core-shell carbon-ceramic fibrous as well as ceramic tubular catalyst supports utilizing electrospinning and atomic layer deposition (ALD). In this paper, ALD of Ti-Nb-O thin films using TiCl4, Nb(OEt)5, and H2O as precursors is demonstrated. According to the time-of-flight-elastic recoil detection analysis and Rutherford backscattering spectrometry, carbon and hydrogen impurities were relatively low, but depend on the pulsing ratio of the precursors. Optimized ALD process was used for coating of sacrificial electrospun polyvinyl alcohol (PVA) template fibers to yield tubular Ti-Nb-O structures after thermal or solution based PVA removal. Anoth…
Q-switching of an erbium-doped fibre laser modulated by a Bragg grating fixed to a piezoelectric
2003
The performance of the Q-switched erbium-doped fibre laser with two fibre Bragg gratings as cavity mirrors was theoretically analysed, employing a set of rate equations for the ion populations and the photon flux inside the cavity. The simulation considers a system where the pulsed laser emission is produced by the temporal modulation of a Bragg grating fixed to a piezoelectric and operating in the 1550 nm spectral region. The temporal evolution of different frequency components of the laser emission produced is governed by the instantaneous overlap between the two gratings. Theoretical results are in agreement with previously reported experimental values.
In vitro power profiles of daily disposable contact lenses
2012
Abstract Purpose To evaluate and compare the distribution of refractive power within the optic zone of different soft contact lenses and to investigate the effect of lens decentration on the power profiles. Methods The Nimo TR1504 instrument was used to measure the optical power across different aperture diameters (from 1.5 mm to 5.5 mm in steps of 0.5 mm) of four daily disposable contact lenses: DAILIES TOTAL1, Proclear 1-Day, SofLens daily disposable and 1-DAY ACUVUE MOIST. Measurements were performed using a wet cell. Power data were evaluated when contact lenses were in its centered position and after inducing different amounts of lens decentration (from 0.2 mm to 1.0 mm in steps of 0.2…
Active shape correction of a thin glass/plastic x-ray mirror
2015
Optics for future X-ray telescopes will be characterized by very large aperture and focal length, and will be made of lightweight materials like glass or plastic in order to keep the total mass within acceptable limits. Optics based on thin slumped glass foils are currently in use in the NuSTAR telescope and are being developed at various institutes like INAF/OAB, aiming at improving the angular resolution to a few arcsec HEW. Another possibility would be the use of thin plastic foils, being developed at SAO and the Palermo University. Even if relevant progresses in the achieved angular resolution were recently made, a viable possibility to further improve the mirror figure would be the app…
Topological insulators and thermoelectric materials
2012
Topological insulators (TIs) are a new quantum state of matter which have gapless surface states inside the bulk energy gap. Starting with the discovery of two dimensional TIs, the HgTe-based quantum wells, many new topological materials have been theoretically predicted and experimentally observed. Currently known TI materials can possibly be classified into two families, the HgTe family and the Bi2Se family. The signatures found in the electronic structure of a TI also cause these materials to be excellent thermoelectric materials. On the other hand, excellent thermoelectric materials can be also topologically trivial. Here we present a short introduction to topological insulators and the…
Influence of plastic deformation on the microstructure and corrosion behaviour of Ti–10Mo–4Zr and Ti–6Al–4V alloys in the Ringer’s solution at 37°C
2015
Abstract The influence of plastic deformation on the microstructure and passivity of Ti–6Al–4V and Ti–10Mo–4Zr is studied. The content of titanium-based compounds in the passive film formed on the alloys increases under straining. In the region where necking occurs, the β-phase content drops in Ti–6Al–4V. The grain orientation spread increases with increasing strain. The quality index of EBSD maps is affected on Ti–10Mo–4Zr (dislocation structures along preferential orientations). The corrosion behaviour is investigated in the Ringer’s solution (37 °C). Results obtained in the anodic and cathodic domains are discussed considering changes described previously.
Burner backflow reduction in regeneration furnace
2011
In the present case from the steel industry, waste hydrochloric acid from the pickling process is regenerated using spray roasting. The process is driven by four burners placed symmetrically along the periphery of the cylindrical main section of the reactor. Severe problems with gas backflow and sintering of iron oxide inside the burner chamber have led to a complete shut down of the process 1-2 times every week, which is a frequency which significantly affects the productivity. In this study the influence of a kick-out on the gas flow in the vicinity of the burner chamber is investigated numerically. It is shown that the kick-out geometry creates a vortical low pressure region preventing t…