Search results for "basalt"
showing 10 items of 223 documents
Experimental investigation on tensile and shear bond behaviour of Basalt-FRCM composites for strengthening calcarenite masonry elements
2023
The use of Fabric Reinforced Cementitious Matrix (FRCM) composites for structural retrofit has seen an increased interest among the scientific community, during the last decade. Various studies have revealed their effectiveness as external retrofitting technique of masonry elements, offering numerous advantages respect to the well know Fibre Reinforced Polymer (FRP) in terms of compatibility with masonry support, reversibility of intervention and sustainability. Despite the growing use, the characterization of FRCM mechanical behaviour is still an open issue, due to numerous uncertainties involved in test set-up adopted and fibre-mortar combination. The proposed experimental study aims to i…
Petrogenesis of Potassic Basalts from Northeast China: New Constraints from Trace Elements in Olivine
2015
M20 M21
Generation of CO2-rich melts during basalt magma ascent and degassing
2013
International audience; To test mechanisms of basaltic ma gma degassing, continuous decompressions of volatile-bearing (2.7-3.8 wt% H2O, 600-1300 ppm CO2) Stromboli melts were performed from 250-200 to 50-25 MPa at 1180-1140°C. Ascent rates were varied from 0.25 to ~ 1.5 m/s. Glasses after decompression show a wide range of textures, from totally bubble-free to bubble-rich, the latter with bubble number densities from 104 to 106/cm3, similar to Stromboli pumices. Vesicularities range from 0 to ~ 20 vol%. Final melt H2O concentrations are homogeneous and always close to solubilities. In contrast, the rate of vesiculation controls the final melt CO2 concentration. High vesicularity charges ha…
Water alteration of rocks and soils on Mars at the Spirit rover site in Gusev crater
2005
The cover shows part of the Larry's Lookout panorama, seen from the Mars Exploration Rover (MER) Spirit during its drive up Husband Hill: the summit is about 200 metres from the rover. Six papers this week report in detail on the MER mission. An Analysis compares predictions used to select a landing site with the conditions actually encountered. This ‘ground truth’ will be invaluable for interpreting future remote-sensing data. Surface chemistry suggests that the upper layer of soil may contain 1% meteoritic material. MER provides a unique glimpse of solar transits of the moons Phobos and Deimos. Rover Opportunity examined wind-related processes, and spectroscopy indicates a dry origin for …
Pull-off adhesion of hybrid glass-steel adhesive joints in salt fog environment
2016
The aim of this paper was to evaluate the durability behaviour of glass/steel adhesive joints exposed to salt fog environmental conditions for ten weeks, according to ASTM B117 standard. To this scope, pull-off mechanical tests were carried out in order to evaluate the performances evolution and damage phenomena of the adhesive joints during the ageing exposition. Two different types of adhesives were compared (i.e. epoxy and polyurethane ones). Moreover, the effects of the glass surface condition and the presence of a basalt mat layer within the adhesive thickness were evaluated. The mechanical performances were related with the occurred failure mechanisms. Epoxy-based joints showed higher…
Ca-rich carbonates associated with ultrabasic-ultramafic melts. Carbonatite or limestone xenoliths? A case study from the late Miocene Morron de Vill…
2016
The volcanic products of the late Miocene Morron de Villamayor volcano (Calatrava Volcanic Field, central Spain) are known for being one of the few outcrops of leucitites in the entire circum-Mediterranean area. These rocks are important because aragonite of mantle origin has been reported as inclusion in olivine macrocrysts. We use petrographic observations, mineral compositions, as well as oxygen and carbon isotope ratios coupled with experimental petrology to understand the origin of carbonate phase in these olivine-phyric rocks. Groundmass and macrocryst olivines range from δ18OVSMOW of +4.8‰, typical of mantle olivine values, to +7.4‰, indicating contamination by sedimentary carbonate.…
The role of melt composition on aqueous fluid vs. silicate melt partitioning of bromine in magmas
2018
International audience; Volcanogenic halogens, in particular bromine, potentially play an important role in the ozone depletion of the atmosphere. Understanding bromine behaviour in magmas is therefore crucial to properly evaluate the contribution of volcanic eruptions to atmospheric chemistry and their environmental impact. To date, bromine partitioning between silicate melts and the gas phase is very poorly constrained, with the only relevant experimental studies limited to investigation of synthetic melt with silicic compositions. In this study, fluid/melt partitioning experiments were performed using natural silicate glasses with mafic, intermediate and silicic compositions. For each co…
Strengthening of Masonry Columns with BFRCM or with Steel Wires: An Experimental Study
2016
Nowadays, innovative materials are more frequently adopted for strengthening historical constructions and masonry structures. The target of these techniques is to improve the structural efficiency with retrofitting methods while having a reduced aesthetical impact. In particular, the use of basalt fiber together with a cementitious matrix emerges as a new technique. This kind of fiber is obtained by basalt rock without other components, and consequently it could be considered a natural material, compatible with masonry. Another innovative technique for strengthening masonry columns consists of applying steel wires in the correspondence of mortar joints. Both techniques have been recently pr…
Experimental Crystallization of a High-K Arc Basalt: the Golden Pumice, Stromboli Volcano (Italy)
2006
International audience; The near-liquidus crystallization of a high-K basalt (PST-9 golden pumice, 49·4 wt % SiO2, 1·85 wt % K2O, 7·96 wt % MgO) from the present-day activity of Stromboli (Aeolian Islands, Italy) has been experimentally investigated between 1050 and 1175°C, at pressures from 50 to 400 MPa, for melt H2O concentrations between 1·2 and 5·5 wt % and {Delta}NNO ranging from –0·07 to +2·32. A drop-quench device was systematically used. AuPd alloys were used as containers in most cases, resulting in an average Fe loss of 13% for the 34 charges studied. Major crystallizing phases include clinopyroxene, olivine and plagioclase. Fe–Ti oxide was encountered in a few charges. Clinopyro…
Influence of anodizing surface treatment on the aging behavior in salt-fog environment of aluminum alloy 5083 to fiber reinforced composites adhesive…
2021
The present work aims to evaluate how an innovative and eco-friendly anodizing process with tartaric-sulfuric acid (TSA) bath and a pore widening in an aqueous solution of NaOH 0.1 M can improve the durability in marine environment of co-cured adhesive joints between an aluminum alloy (AA 5083) and fiber (i.e., glass or basalt)-reinforced composite substrates. The aging was carried out by exposing samples to salt-fog spray conditions (5 wt.% NaCl) for 30, 60 and 90 days in a climate chamber, in accordance with ASTM B117. In order to get further insights on the aging behaviour of bonded joints, neat matrix was also exposed to the same environment for 60 days. Quasi-static mechanical tests an…