Search results for "business.product_category"
showing 10 items of 376 documents
Stereoacuity with simultaneous vision multifocal contact lenses.
2010
Our purpose was to evaluate near stereoacuity (SA) with Focus Progressives and PureVision Multifocal simultaneous vision contact lenses. In a cross-over study design, 20 presbyopic subjects were fitted with either the Focus Progressives or PureVision Multifocal lenses. After 1 month, SA was measured with the vectographic Titmus, Random dot stereotests, and the Howard-Dolman apparatus under photopic conditions (85 lux) at 40 cm. Binocular high-contrast visual acuity at distance and near was examined. Subjects were then refitted with the alternative correction and the procedure was repeated. Mean SA with the Focus Progressive was 21 +/- 7 sec arc, 54 +/- 17 sec arc, and 51 +/- 21 sec arc, wit…
Separation of motor oils, oily wastes and hydrocarbons from contaminated water by sorption on chrome shavings
2007
In this paper, the ability of chrome shavings to remove motor oils, oily wastes and hydrocarbons from water has been studied. To determine amount of hydrocarbons sorbed on tanned wastes, a FT-NIR methodology was used and a multivariate calibration based on partial least squares (PLS) was employed for data treatment. The light density, porous tanned waste granules float on the surface of water and remove hydrocarbons and oil films. Wastes fibers from tannery industry have high sorption capacity. These tanned solid wastes are capable of absorbing many times their weight in oil or hydrocarbons (6.5-7.6g of oil and 6.3g of hydrocarbons per gram of chrome shavings). The removal efficiency of the…
A Theoretical Approach to the Shift Mechanics of Rubber Belt Variators
2008
This paper proposes a theoretical description of the mechanical behavior of rubber belt variators during the speed ratio shift. Comparing with the steady operation, the mass conservation of the belt is completely reformulated considering an elementary dihedral control volume between two planes through the pulley axis and balancing the inside mass variation with the total mass flux through the control surface. On the other hand, the belt equilibrium conditions are similar to the steady case, as the inertia forces due to the shifting motion are negligible with respect to the other forces. Assuming a one-dimensional belt model, it is shown that adhesive regions may appear inside the arc of con…
Microfluidic Fabrication of Physically Assembled Nanogels and Micrometric Fibers by Using a Hyaluronic Acid Derivative
2017
The employ of a hyaluronic acid (HA) derivative, bearing octadecyl (C18) and ethylenediamine (EDA) groups, for microfluidic fabrication of nanogels and microfibers is reported in this study. Two HA-EDA-C18 derivatives (125 and 320 kDa) having ionic strength sensitive properties are synthesized and characterized. The control of the rheological properties of HA-EDA-C18 aqueous dispersions by formation of inclusion complexes with hydroxypropyl-β-cyclodextrins (HPCD) is described. Reversibility of C18/HPCD complexation and physical crosslinking is detected in media with different ionic strength through oscillation frequency tests. HA-EDA-C18 125 kDa is employed for nanogel fabrication. Control …
ESCA-Analysis of tin compounds on the surface of hydroxyapatite
1997
The formation of tin compounds on the surface of hydroxyapatite, the main crystalline component of teeth, is discussed controversially. SnF2 is used as an anticaries agent in toothpaste preparations. Pure hydroxyapatite (HAP) is treated with extracts of commercially available toothpastes containing tin fluoride and analyzed by electron spectroscopy (ESCA). Survey spectra and depth profiles are recorded. The chemical shifts measured for the HAP samples are compared with those of standard tin compounds. It is concluded that on the surface of hydroxyapatite a mixture of two-valent fluoro-phosphato compounds is formed. SnO is not found in the mixture.
Considerations on factors affecting biochar densification behavior based on a multiparameter model
2021
The optimization of upscaled biochar pelleting is limited by lack of knowledge regarding the effects of process parameters. A multiparameter model, coupled to a single pellet press unit, was for the first time applied to biochar production to predict the upscaled biochar pelleting process behavior. The model permits to estimate in a time and cost-effective way how the die friction forces, quantified through the pellet exiting pressure, are affected by the key process parameters. It was observed that to achieve acceptably low exiting pressures (in the order of 100 MPa), it was critical to produce biochar at high temperatures (e.g. 600 °C). Addition of water as a binder is also beneficial, wh…
Spark Plasma Sintering tool design for preparing alumina-based Functionally Graded Materials
2016
Abstract A way to produce Functionally Graded Materials (FGM) is by means of Spark Plasma Sintering (SPS) and specifically designated tools. These new tools permit a current density modulation and therefore a temperature variation along the z-axis. The key feature relies on a varying die section. FEM modelling has given the suitable range of die dimensions between the top and the bottom to obtain a given temperature gradient (around 300 °C) out of roughly a 15 mm height. Experiments conducted in different configurations (with or without samples) and the measurement of the associated thermal gradient led to improvements of the mould (in particular the introduction of a counter-piston). By th…
A depth dependent analytical approach to determine material breaking in SPIF
2007
Formability is a relevant issue in Single Point Incremental Forming (SPIF) process since it is one of the main point of strength together to the possibility to avoid any dedicated die. Several researches agree that, depending on working material and process parameters, in SPIF operations there is a threshold slope of the wall that cannot be overcame without material breaking. If deep Incremental Forming is taken into account, despite the previous statement it is possible to demonstrate that, when the threshold angle is imposed, there is a relation between the actual workpiece depth and the material breaking approaching. In this paper, the latter relationship was investigated and formally de…
Does mechanical locking-base ceramic brackets reduce cracks at debonding?
2012
Objectives: Debonding of chemically bonded ceramic brackets has been mostly led to enamel damages. This study aimed to evaluate enamel cracks followed by debonding ceramic brackets with mechanical retention. Study Design: Sixty extracted human premolar teeth were randomly divided into two groups. Metallic brackets and recently available ceramic brackets with mechanical retention were bonded to the teeth in first (MB) and second (CB) group respectively. After a week, the brackets were debonded using a pair of bracket-removing pliers assembled to a testing machine. Optical stereomicroscope and trans-illumination techniques were used to calculate the cracks and measure their length before bond…
Limits of the Open-Die Forward Extrusion: Numerical Analysis and Experimental Tests
1992
In the paper the open-die forward extrusion process is analysed in order to determine the influence of the most important geometrical and frictional parameters on the practical suitability of the operation. Experimental tests have been carried out and their results have been compared with the numerical ones derived by FEA.