Search results for "cavity"
showing 10 items of 641 documents
Methane line parameters in the HITRAN2012 database
2013
International audience; The compilation of methane molecular line parameters was updated to include new global analyses and measurements for 12CH4, 13CH4 and 12CH3D. Over 70% of the methane parameters in HITRAN2008 were replaced; existing parameters retained were the microwave lines and the Dyad of 13CH4 near 7 μm and ν6 of 13CH3D near 8.7 μm, 12CH3D (7-4076 cm-1), hot bands of 12CH4 (1887-3370 cm-1) and normal sample CH4 (4800-5550 cm-1 and 8000-9200 cm-1). With a minimum intensity at 296 K in units of cm-1/(molecule cm-2) set to 10-37 for the far-IR and 10-29 for the mid- and near-IR, the methane database increased from 290,091 lines in HITRAN2008 to 468,013 lines, and three-fourths of th…
Anin vitroendodontic model to quantify the accessory canal filling potential of the vertical and lateral condensation techniques
2021
The purpose of this study was to determine the accessory canal filling potential of vertical and lateral condensation techniques in simulated root canals. A total of 130 prepared transparent, straight-simulated root canals with nine accessory canals (0.02 mm), prepared at different levels from the apical, were obturated with vertical (n = 100) and 30 lateral condensation (n = 30) techniques. 50.33% of the accessory canals obturated with vertical condensation were completely filled with gutta-percha; 37.78% completely filled with gutta-percha and sealer. 61.11% of the accessory canals were completely filled with sealer only using the lateral condensation technique. The vertical condensation …
Thickness sensitivity of ultrasound velocity in long bone phantoms
2004
One approach to bone disease diagnosis such as osteoporosis is to measure the velocity of ultrasound propagating axially along long bones. In this study, the variation in velocity as a function of radial position was assessed using two polyvinyl chloride (PVC) bone phantoms with cross-sectional geometry similar to the human tibia but differing in medullary cavity diameter. Two ultrasonometers were used: these were a commercial device operating at a relatively high frequency (HF) of 1.25 MHz and a prototype low frequency (LF) device operating at approximately 200 kHz. The LF measurements showed a larger variation with radial position, with changes in velocity of up to 20% occurring around th…
Understanding the Conversion Process of Magnetron-Deposited Thin Films of Amorphous ReO$_x$ to Crystalline ReO$_3$ upon Thermal Annealing
2020
Crystal growth & design 20(9), 6147 - 6156 (2020). doi:10.1021/acs.cgd.0c00848
Assessment of root canal enlargement using Mtwo and BioRace rotary files.
2014
Objective. To evaluate root canal enlargement following mechanical shaping using 2 nickel titanium rotary systems.Material and Methods. Forty single-rooted teeth were immersed in resin and sectioned perpendicular to the long axis at 4, 8, and 12 mm from the apex. Digital capture of sections was performed before and after canal instrumentation using Mtwo and BioRace instruments. The area increase of endodontic space was calculated by subtraction.Results. The use of both instruments has allowed the removal of great amounts of dentin from the canal walls, even when the endodontic morphology is characterized by awkwardness to reach recesses.Conclusions. Both procedures seem to be valid and no d…
Development and analysis of a model based on chirped fiber Bragg gratings employed for cracks characterization in materials
2018
In this work a model was developed that allows to understand the behavior of a chirped fiber Bragg grating for the detection and characterization of cracks in materials. In addition to the amplitude response, we show that the group delay of the grating provides useful information for the characterization of the crack. The position of the crack can be determined thanks to the linear chirp of the grating that fixes a correlation between the spatial position and both, the wavelength and the group delay. However, our analysis shows that this simple approach has a source of error, which can be overcome if a controllable external strain can be applied to the embedded grating, additional to the st…
Effect of cavity preparation instruments (oscillating or rotating) on the composite-dentin interface in primary teeth.
2003
Abstract Objectives: To evaluate the effect of preparation of instruments on the interfacial integrity between cavity wall and composite restoration. Methods: Two class II slot preparations were done in 10 primary teeth either with SonicSys® or with a conventional bur. The cavities were filled using an adhesive system. One layer of a flowable composite and one layer of a condensable composite were applied. The specimens were analyzed by confocal laser scanning microscopy. Results: In the SonicSys® group the mean thickness of the hybrid layer was 6.12 (0.60) μm; in the control group it was 6.04 (0.63) μm. The difference was not statistically significant. Two fractures were observed in one to…
Influence of cavity preparation technique (rotary vs. ultrasonic) on microleakage and marginal fit of six end-root filling materials
2010
Objectives: To evaluate in vitro the effect of cavity preparation with microburs and diamond-coated ultrasonic tips on the microleakage and marginal fit of six end-root filling materials. Study Design. The following materials were assessed: amalgam (Amalcap), zinc oxide eugenol (IRM), glass ionomer (Vitrebond), compomer (Cavalite), mineral particle aggregate (MTA) and composite (Clearfil). Cavity preparation was performed with microburs or diamond ultrasonic tips in single-root teeth. The seal was evaluated in two experiments: a microleakage assay on the passage of dye to the interface; and a scanning electron microscopy study and analysis of epoxy resin replicas, measuring the size of gaps…
Tunable dual-wavelength operation of an all- fiber thulium-doped fiber laser based on tunable fiber Bragg gratings
2018
Tunable dual-wavelength emission of a Tm-doped fiber laser based on two fiber Bragg gratings (FBGs) is experimentally demonstrated. By using two FBGs with central wavelengths at 2069.30 and 2069.44 nm, stable dual-wavelength laser generation in the 2 ?m wavelength region is achieved by adjusting the differential loss of the two wavelengths in the laser cavity. Strain applied on the FBG allows independent tuning of the simultaneously generated wavelengths with separation between the laser lines in a range from 0.54 to 9 nm. The laser has output power fluctuations less than 0.093% for an output power of 77.3 mW.
Electrochemical Fabrication and Physicochemical Characterization of Metal/High-k Insulating Oxide/Polymer/Electrolyte Junctions
2014
Photoelectrochemical polymerization of poly(3,4-ethylenedioxythiophene), PEDOT, was successfully realized on anodic film grown to 50 V on magnetron sputtered Ti-6 atom % Si alloys. Scanning electron microscopy allowed us to evidence formation of compact and uniform polymer layers on the oxide surface. Photoelectrochemical and impedance measurements showed that photopolymerization allows one to grow PEDOT in its conducting state, while a strong cathodic polarization is necessary to bring the polymer in its p-type semiconducting state. Information on the optical and electrical properties of metal/oxide/polymer/electrolyte junctions proves that PEDOT has promising performance as an electrolyte…