Search results for "characterization"
showing 10 items of 1054 documents
Characterization of Biomass Activity in Conventional and Hybrid MBR Pilot Plants by Means of Respirometric Techniques
2012
abstract
Quality Assurance and Support Measures for Solar Cooling on System Level
2016
Abstract Within the IEA SHC Task 48 “Quality assurance and support measures for Solar Cooling” the analysis and evaluation of the systems has been one of the four main focuses. Here the activities are including the lab- and field-based characterization of the systems, the definition and application of performance figures, a guideline for a reliable monitoring procedure including methods for automated error detection and an updated overview on worldwide installed DEC systems including hints and good practice examples. They are furthermore leading to three different easy-to-use tools for solar cooling systems: The LCA tool considers environmental and energetic values for the evaluation, the P…
Dynamic characterization for the dielectric electroactive polymer fundamental sheet
2012
Published version of an article published in the journal: International Journal of Advanced Manufacturing Technology. Also available from the publisher at: http://dx.doi.org/10.1007/s00170-012-4423-6 A study into the appropriateness of characterizing the dynamics of the dielectric electroactive polymer (DEAP) fundamental sheet has been performed. Whereby a model describing the dynamics of the DEAP fundamental sheet is developed, parameters of the models are determined using experimental/simulation results, and verification has been conducted to determine the precision of the dynamic model. The precision for the DEAP sheet-obtained dynamic model could not be verified unless some parameters c…
A new methodology for distribution systems faults identification, location and characterization
2005
PurposeIdentify a new methodology for fault characterization, identification and location in electrical distribution systems, based on the use of matrix algebra.Design/methodology/approachThe developed diagnostic methodology is based on a high precision analytical model of the network using a distributed parameters representation.FindingsTest results have proved the approach to be efficient and precise, while providing a generalized quadripolar model of a line affected by the most common kinds of fault.Research limitations/implicationsGeneralization to a greater number of fault cases, experimental tests.Practical implicationsUtilities are quite interested in such items, since the new requir…
Impact of molecule-based magnetic materials: A critical outlook
2009
Abstract A critical outlook of the field of molecular magnetic materials is presented. This article is inspired by an international symposium devoted to the “ Design, Characterization and Modelling of Molecule-Based Magnetic Materials (DCM4-II)” that took place at Strasbourg (France), from May 28th to June 1st, within the E-MRS 2007 Spring Meeting (Symposium R) organized by the European Materials Research Society in collaboration with the European Science Foundation . A series of papers linked to this symposium are published in this issue and in the previous issue (Volume 11, Issue 4) of Solid State Sciences.
CIGS PV Module Characteristic Curves Under Chemical Composition and Thickness Variations
2014
This paper analyzes how the electrical characteristics of a CIGS photovoltaic module are affected by the chemical composition and by the thickness variations of the CIGS absorber. The electrical characteristics here considered are the short circuit current, the open circuit voltage, the efficiency and the power peak. The chemical composition is varied by tuning the ratio between gallium and indium. This analysis has been performed by means of the wxAMPS software, developed by the University of Illinois. The above variations have been taken into account on a PV module made of 72 cells. This analysis has been carried out employing a PV module mathematical model developed and implemented by th…
Thermal characterization of insulating materials
2018
Abstract The strict energy saving standards are based on the declared values of the materials, i.e. U-value, thermal conductivity or thermal capacity. To this end, proper knowledge of the thermophysical properties of the wall components is needed, especially with regard to new lightweight technologies that are being used in building construction/refurbishment, under the dynamic conditions of the Mediterranean climate, where one of most important parameters of building materials is their heat capacity because of the influence of solar radiation energy. With this regard, the actual heat capacity value, obtained in laboratory tests, is typically quite different from the nominal one. So, this p…
NB PLC and Software Defined Networking for Smart Grid Applications
2017
During the last years, the installation of Distributed Energy Resources (DERs) and the expected diffusion of Electrical Vehicles (EVs), is increasing the complexity of the distribution grid, making the management of the grid operated by Distribution System Operators (DSOs) more difficult. The Smart Grid approach tries to provide a response to these troubles, by means of a strong interaction between the power grid and Information and Communication Technology (ICT) infrastructures. The drawback of this approach is an increase in the management effort of the ICT infrastructures, for which the DSO are not prepared. Software Defined Networking (SDN) is an approach developed to manage complex ICT…
Electrical characterization of CIGSSe photovoltaic modules
2017
This work describes the electrical characterization of CIG(S,Se) 2 sub-modules in order to compare the related performances with those obtained from traditional silicon photovoltaic modules. This characterization has been performed through means of a test bench, mainly composed by a solar simulator equipment, allowing the determination of the parameters of the prototypes under test at different irradiances and temperatures.
Experimental characterization of a wind generator prototype for sustainable small wind farms
2016
This paper presents the experimental characterization of a wind turbine prototype used for micro wind farms. The proposed prototype, whose advantages can be summarized in versatility of application, low noise and compactness, can generate 1 kW of rated power for a wind speed equal to 4 m/s. The tests here reported and carried out by means of an experimental test bench confirm that the prototype is well designed and adequate for the purpose of its application.