Search results for "cladding"
showing 10 items of 62 documents
Determination of refractive index of submicron-thick films using resonance shift in a four-layer slab waveguide
2017
The measurement of refractive index of very thin films at the order of ten to hundred nanometers is cumbersome and usually requires employing sophisticated techniques such as the spectral ellipsometry. In this paper we describe a simple contact method for measuring the refractive index of thin films. Here we have used the prism-coupling technique for characterizing samples prepared as four-layer slab waveguides. The waveguide resonance condition can be calculated by solving simple analytic transcendental equations for the slab waveguide. Then the captured mode position as a function of cladding thickness is used for probing the refractive index of cladding layer. We used indium-tin-oxide la…
Optimisation of refractory coatings realised with cored wire addition using a high-power diode laser
2005
Laser; Cladding; Refractory alloys; Factorial experiments; International audience; The objective or our research was to obtain refractory alloys using the high-power diode laser (HPDL) coating technique. After optimisation using factorial experiments, two different cladding regimes were clearly distinguished. It was also shown that a very narrow transition zone exists between the two regimes, and, inside this zone, clad layers having a satisfactory compromise between the response functions (surface aspect and cavity presence) were obtained. The main objective of our study, namely, the control of the operating parameters (geometrical and kinematical) to realise adequate coatings, without cav…
<title>Fibers supporting super-Gaussian beams: cladding effects</title>
1996
We define a matching function that describes the amplitude variations produced over supergaussian beams, by cladding optical fibers that, if uncladded, can sustain this type of beams as Eigenmodes.
A Refractive Index Sensor Based on the Resonant Coupling to Cladding Modes in a Fiber Loop
2013
We report an easy-to-build, compact, and low-cost optical fiber refractive index sensor. It consists of a single fiber loop whose transmission spectra exhibit a series of notches produced by the resonant coupling between the fundamental mode and the cladding modes in a uniformly bent fiber. The wavelength of the notches, distributed in a wavelength span from 1,400 to 1,700 nm, can be tuned by adjusting the diameter of the fiber loop and are sensitive to refractive index changes of the external medium. Sensitivities of 170 and 800 nm per refractive index unit for water solutions and for the refractive index interval 1.40-1.442, respectively, are demonstrated. We estimate a long range resolut…
Sensitivity optimization with cladding-etched long period fiber gratings at the dispersion turning point
2016
This work presents a refractive index sensor based on a long period fiber grating (LPFG) made in a reduced cladding fiber whose low order cladding modes have the turning point at large wavelengths. The combination of these parameters results in an improved sensitivity of 8734 nm/refractive index unit (RIU) for the LP0,3 mode in the 1400-1650 wavelength range. This value is similar to that obtained with thin-film coated LPFGs, which permits to avoid the coating deposition step. The numerical simulations are in agreement with the experimental results. This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R. J.L. Cruz also acknowledges financial s…
Use of Ultrasound in Reconditioning by Welding of Tools Used in the Process of Regenerating Rubber
2018
Addressing the problem of reconditioning large parts is of particular importance, due to their value and to the fact that the technologies for their reconditioning are very complex. The tools used to refine regenerated rubber which measure 660 mm in diameter and 2130 mm in length suffer from a rather fast dimensional wear. Within this research, the authors looked for a welding reconditioning procedure that would allow a very good adhesion between the deposited material layer and the base material. In this regard, the MAG (Metal Active Gas) welding process was used, but the ultrasonic activation of the welding process was also considered. Thus, the wire used for welding was activated conside…
Temperature imaging and image processing in the steel industry
1996
Our aim is twofold: to present our temperature measurement system based on CCD technology, which gives a linear response versus temperature, and to display two industrial applications in which our system has been involved to optimize and characterize the process. We present a short summary dealing with temperature evaluations from radiation measurements. We consider especially the problems of the surroundings, the atmosphere, and the emissivity assumption. After selecting a value for the emissivity, we show that the use of the CCD technology enables us to obtain high spatial and temporal resolution temperature imaging, and provides further information, mainly a linear response versus temper…
Magnesium alloys laser (Nd:YAG) cladding and alloying with side injection of aluminium powder
2003
International audience; The development of the high purity magnesium alloys (such as WE43) incites the designers to reconsider them, and the car industry appears, these days, the most interested to use this kind of alloy. However, due to their ignitability and tendency to oxidation, magnesium alloys require surface treatments. A series of experiments was carried out in order to improve the corrosion resistance of two types of magnesium alloys, WE43 and ZE41. In most cases, the substrate surface was treated before laser interaction. Side injection of aluminium powder under a 3 kW cw Nd:YAG laser was employed. The deposited layers present very good bond properties. The resulting microstructur…
The durability of basalt fibres reinforced polymer (BFRP) panels for cladding
2015
The study focuses on two basalt composite laminate panels for cladding, produced by means of vacuum bagging technique. In particular, unidirectional and random basalt fabrics, with different areal weights, using epoxy resin as matrix, were used. According to the ISO 15686 methodology for the evaluation of durability, samples were subjected to cycles of artificial aging in climatic chamber and outdoor exposure, carrying out mechanical (i.e. quasi-static and dynamic) and calorimetric tests. The results show the effectiveness over time of produced basalt composite laminates and the initial increase of the mechanical performances after the first steps of accelerated aging.
Contributions regarding increasing reliability of beer industry installations using weld cladding in ultrasonic field
2016
Paper presents a new technology for availability increasing of different installation parts used in beer industry - ultrasonic activation of metal deposition by welding. The dilution phenomenon is studied linked on its influence upon material technological and functional properties in the three distinct zones of resulted couple (filler material, influenced thermal zone, base material). Experimental results performed on unidirectional valve are presented regarding variation of chemical composition concentration and dilution variation in three zones influenced by ultrasonic wave.