Search results for "code"
showing 10 items of 1180 documents
Increasing the shear capacity of reinforced concrete beams using pretensioned stainless steel ribbons
2017
In this work, the second part of an experimental campaign investigating the efficiency of an alternative retrofitting method for increasing the flexural and/or shear capacity in reinforced concrete beams, based on the use of prestressed stainless steel ribbons and steel angles, is presented and analytically reproduced. This group of tests focuses on the ability of the adopted retrofitting method to improve the shear strength and ultimate deformation of reinforced concrete structural elements. As described in a companion paper, the adopted retrofitting method is alternative to traditional techniques of reinforced concrete retrofitting, being easy to install and usually reversible, and charac…
Coded excitation speeds up the detection of the fundamental flexural guided wave in coated tubes
2016
The fundamental flexural guided wave (FFGW) permits ultrasonic assessment of the wall thickness of solid waveguides, such as tubes or, e.g., long cortical bones. Recently, an optical non-contact method was proposed for ultrasound excitation and detection with the aim of facilitating the FFGW reception by suppressing the interfering modes from the soft coating. This technique suffers from low SNR and requires iterative physical scanning across the source-receiver distance for 2D-FFT analysis. This means that SNR improvement achieved by temporal averaging becomes time-consuming (several minutes) which reduces the applicability of the technique, especially in time-critical applications such as…
Beta forging of Ti-6Al-4V: Microstructure evolution and mechanical properties
2013
Titanium alloys are finding an increasing use in the aeronautical field, due to their characteristics of high mechanical properties, lightness and corrosion resistance. Moreover these alloys are compatible with the carbon fibre reinforced plastics that are also finding a wide use in the aeronautical field. On the other hand the use of these alloys implies some drawbacks, for example titanium alloys are often considered more difficult to form and generally have less predictable forming characteristics than other metallic alloys such as steel and aluminum. In this paper was studied both the microstructure evolution and the mechanical properties of a Ti-6Al-4V rolled bar after hot forging. The…
Low loss microstructured chalcogenide fibers for large non linear effects at 1995 nm
2010
International audience; Microstructured optical fibers (MOFs) are traditionally prepared using the stack and draw technique. In order to avoid the interfaces problems observed in chalcogenide glasses, we have developed a new casting method to prepare the chalcogenide preform. This method allows to reach optical losses around 0.4 dB/m at 1.55 µm and less than 0.05 dB/m in the mid IR. Various As(38)Se(62) chalcogenide microstructured fibers have been prepared in order to combine large non linear index of these glasses with the mode control offered by MOF structures. Small core fibers have been drawn to enhance the non linearities. In one of these, three Stokes order have been generated by Ram…
Simulation of Young’s moduli for hexagonal ZnO [0 0 0 1]-oriented nanowires: first principles and molecular mechanical calculations
2017
The authors thank A Gulans, B Polyakov and S Vlassov for stimulating discussions. This study has been supported by the ERA.Net RUS Plus project No. 237 Watersplit. AB, RE and SL acknowledge the financial support by the Russian Foundation for Basic Research (Grant No. 17-03-00130-a) and the assistance of the Saint Petersburg State University Computer Center in the accomplishment of high-performance computations.
Analysis of multipactor RF breakdown in a waveguide containing a transversely magnetized ferrite
2016
In this paper, the multipactor RF breakdown in a parallel-plate waveguide partially filled with a ferrite slab magnetized normal to the metallic plates is studied. An external magnetic field is applied along the vertical direction between the plates in order to magnetize the ferrite. Numerical simulations using an in-house 3-D code are carried out to obtain the multipactor RF voltage threshold in this kind of structures. The presented results show that the multipactor RF voltage threshold at certain frequencies becomes considerably lower than for the corresponding classical metallic parallel-plate waveguide with the same vacuum gap
On the use of front-end cascode rectifiers based on normally on SiC JFET and Si MOSFET
2014
The new wide band-gap semiconductor devices provide new properties to be explored. Normally on silicon carbide (SiC) JFET power devices have several advantages, in particular low switching losses and the potential capabilities of high temperature and high reverse blocking voltage. Looking for improving the overall efficiency in power converters, new structures based on these power devices might be studied. In this paper, a cascode rectifier based on normally on SiC JFET is presented and analyzed. This rectification structure can be applied as front-end rectifier stage for ac-dc power converters, increasing the overall efficiency of these topologies. A second cascode rectifier based on silic…
Feedback Biasing Based Adjustable Gain Ultrasound Preamplifier for CMUTs in 45nm CMOS
2018
As CMOS technology is scaled down, supply voltages are decreasing and intrinsic gain of the nanoscale CMOS transistors is dropping while the threshold voltages of transistors are remaining relatively constant. In such scaled down nanoscale CMOS technologies, conventional vertical stacking architectures (for example. cascode architectures) for high-gain becomes no more attractive. In this paper we present the analysis and design of a feedback biasing based adjustable gain ultrasound preamplifier which is capable of amplifying signals from 15 MHz to 45 MHz from Capacitive Micromachined Ultrasound Transducers (CMUTs) in 45nm CMOS technology for medical ultrasound imaging applications. From the…
Novel Methodologies to Model Charge Transport in Metal-Air Batteries
2018
Implementing some Evolutionary Computing Methods for Determining the Optimal Parameters in the Turning Process
2015
In this paper, we comparatively present two heuristics search methods – Simulated Annealing and Weighted Sum Genetic Algorithm, in order to find optimal cutting parameters in turning operation. We consider five different constraints aiming to achieve minimum total cost of machining. We developed a customizable software application in Microsoft Visual Studio with C# source code, flexible and extensible that implements the optimization methods. The experiments are based on real data gathered from S.C. “Compa” S.A Sibiu, a company that manufactures automotive components and targets improving of product quality and reducing cost and production time. The obtained results show that, although the …