Search results for "composites"
showing 10 items of 1905 documents
Nucleation kinetics in deionized charged colloidal suspension
2011
A systematic experimental study on the nucleation, crystallization and crystal-growth of one-componentcharged colloidal particles (122 nm diluted in pure water with densities between 0.5 μm−3bnpb5 ...
The structural properties of soda–silicate sols and of the lime–soda–silicate gel formation
1999
Abstract Alkaline silicate solutions were prepared with varying SiO 2 –Na 2 O ratios, Rm=[SiO 2 ]/[Na 2 O]=2 or 3, with a constant silica concentration equal to 1.5 M. The structure and the number fraction of different silicate molecular species present in the solutions were classically determined for molar ratio Rm=2 using 29 Si nuclear magnetic resonance ( 29 Si NMR). In the case of the sample with Rm=3, for which no NMR data was available, we used small-angle X-ray scattering (SAXS) experiments to get this information. The SAXS model was previously tested with Rm=2 silicate solution. When Ca ++ is added to alkaline silicate solutions, a gel is obtained under well-defined conditions. The …
Paramagnetic germanium-related centers induced by energetic radiation in optical fibers and preforms
2009
International audience; We investigated the creation processes of Ge-related paramagnetic point defects in silica fibers and preforms, doped with different amounts of germanium, and X-ray irradiated at several radiation doses. Different paramagnetic defect species, like GeE0, Ge(1) and Ge(2), were revealed by electron paramagnetic resonance measurements and their concentration was studied as a function of the irradiation dose. The comparison with the optical absorption spectra points out the main role of Ge(1) on the optical transmission loss of fibers in the UV region.
Effects of clearance on thick, single-lap bolted joints using through-the-thickness measuring techniques
2011
Composite materials have increasingly become more common in ground transportation. As this occured thicker panels, as compared to composite panels used in aviation, become necessary in order to withstand high impact loads and day to day degradation. The effectiveness of these panels was often limited by the strength of the joint in which the panel was attached to the frame of the vehicle. Investigating methods of reducing strain concentrations within these joints would increase the effectiveness in using composite materials in ground transportation applications by increasing the load necessary for joint failure to occur. In this study, fiber optic strain gages were embedded in a composite p…
Design of Er3+-doped chalcogenide glass laser for MID-IR application
2009
Abstract The feasibility of a photonic crystal fiber laser (PCF laser), made of a novel Er 3+ -doped chalcogenide glass and operating at the wavelength λ s = 4.5 μm is investigated. The design is performed on the basis of spectroscopic and optical parameters measured on a fabricated Er 3+ -doped Ga 5 Ge 20 Sb 10 S 65 chalcogenide bulk sample. The simulations have been performed by employing a home made numerical code that solves the multilevel rate equations and the power propagation equations via a Runge-Kutta iterative method. The numerical results indicate that a laser exhibiting slope efficiency close to the maximum theoretical one and a wide tunability in the wavelengths range where t…
X-ray irradiation effects on a multistep Ge-doped silica fiber produced using different drawing conditions
2011
International audience; We report an experimental study based on confocal microscopy luminescence (CML) and electron paramagnetic resonance (EPR) measurements to investigate the effects of the X-ray (from 50 krad to 200 Mrad) on three specific multistep Ge doped fibers obtained from the same preform by changing some of the drawing conditions (tension and speed). CML data show that, both before and after the irradiation, Germanium Lone Pair Center (GLPC) concentrations are similarly distributed along the diameters of the three fibers and they are partially reduced by irradiation. The irradiation induces also the Non Bridging Oxygen Hole Center (NBOHC) investigated by CML and other paramagnet…
Ultraviolet-visible light-induced solarisation in silica-based optical fibres for indoor solar applications
2021
Abstract The transmission performances of pure- and doped-silica (a-SiO2) optical fibres are compared during the exposure to a high-power broadband light source approximating the solar spectrum. From the Gaussian decomposition of the attenuation spectra, we found that Al- and P-doped fibres show a fast solarisation effect which leads to transmission degradation in the ultraviolet-visible range. Similarly, Ge-doped fibres undergo photoinduced colour-centre formation which, however, does not prevent visible-light propagation. One of the two tested pure-silica fibres results completely unaffected by light exposure whereas the other shows an absorption band probably due to the presence of chlor…
Oxygen permeability of hydrogel contact lenses with organosilicon moieties
2002
Oxygen transport through two extended wear (day and night) hydrogel contact lenses that contain organosilicon moieties (balafilcon A and lotrafilcon A) was studied in the hydrate (hydrogel) and dry (xerogel) states. The water uptake increased the oxygen permeability [(Dk)app] and transmissibility [Dk/L(av)] coefficients of the dry materials by about 70%. The (Dk)app for the hydrated lenses was determined following the so-called stack procedure. The values obtained were 107 +/- 4 barrer for balafilcon A and 141 +/- 5 barrer for lotrafilcon A, about 5-10 times larger than those previously reported for conventional (without organosilicon moieties) extended wear hydrogels contact lenses. The Dk…
The application of AI techniques in the optimal design of multi-pass cold drawing processes
2001
Abstract In the paper the problem of optimal pass schedule design in multi-pass wire drawing process is investigated. An automatic design procedure based on an effective artificial intelligence (AI) technique, namely simulated annealing (SA), is proposed. The developed algorithm is aimed to achieve a satisfactory balance of the drawing stresses on the material along the reduction sequence, maintaining in the meantime the drawing stress at each pass below a safety value. In this way both the optimal number of passes and the optimal drawing sequence are determined. The effectiveness of the design procedure is tested through the comparison of the sequences suggested by the algorithm with a set…
(o-Phenyleno)naphthalene diimides: a pink fluorescent chromophore
2017
(o-Phenyleno)naphthalene dianhydride 7 was synthesized by a six-step reaction. Imidizations of 7 led to various diimides 8. Their optical and electrochemical properties hold promise for organic electronics.