Search results for "composites"
showing 10 items of 1905 documents
A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites
2012
Experimental investigations on flax and glass fabrics reinforced epoxy specimens, i.e. FFRE and GFRE, submitted to fatigue tests are presented in this paper. Samples having [0/90]3S and [±45]3S stacking sequences, with similar fibre volume fractions have been tested under tension–tension fatigue loading. The specific stress-number of cycles to failure (S–N) curves, show that for the [0/90]3S specimens, FFRE have lower fatigue endurance than GFRE, but the [±45]3S FFRE specimens offer better specific fatigue endurance than similar GFRE, in the studied life range (<2 × 10^6). Overall, the three-stage stiffness degradation is observed in all cases except for [0/90]3S FFRE specimens, which prese…
Generation and characterization of T40/A5754 interfaces with lasers
2014
Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…
Bilayer graded Al/B4C/rice husk ash composite: Wettability behavior, thermo-mechanical, and electrical properties
2018
In this study, wettability behavior of B4C substrate as well as B4C/crystalline rice husk ash and B4C/amorphous rice husk ash substrates with two aluminum alloys were studied. The electrical resistivity, thermal expansion coefficients, and thermal diffusivity of bilayer Al/B4C/rice husk ash composite fabricated by one-step pressureless infiltration were measured and the obtained data were systemically analyzed using the Taguchi method and analysis of variance. Boron carbide substrates after addition of amorphous or crystalline rice husk ash display good wettability with molten aluminum alloys. The results show that, electrical resistivity of Al/B4C/rice husk ash composites is mainly influe…
Stress field model for strengthening of shear-flexure critical RC beams
2017
A model for the design of shear-flexure critical reinforced concrete elements strengthened with fiber-reinforced polymer (FRP) sheets and plates is presented. The model is based on the stress field approach and the equilibrium method and accounts for the different failure modes of FRP, focusing on the debonding of the FRP from the concrete surface. The efficiency of the model in the strength assessment of beams reinforced with FRP by the prediction of the shear-flexure capacity is checked by corroborating the results of several experimental tests found in the literature. Moreover, the presented model's capacity to reproduce experimental behavior is compared with the formulations suggested b…
Response of Cross-Ply Composite to Off-Axis Loading
2002
Polymer composites are known to exhibit nonlinear stress–strain response due to nonlinearly elastic or plastic deformation of the matrix and damage accumulation. Mechanistic modeling of material response explicitly accounting for these interacting factors often leads to complex theories. Plasticity theory formalism provides an alternative for nonlinear deformation description of composite material. We examine the applicability of an orthotropic plasticity model, developed by Sun et al. for unidirectionally reinforced composite, to composite laminate. The response of a symmetric and balanced cross-ply glass/epoxy laminate is studied under uniaxial tensile loading at different angles to the …
Experimental characterization of composite laminates under low-velocity multi-impact loading
2019
The use of composite materials undergoes a significant growth in many industries including aeronautic, railway, and automotive. Laminated composites are often subjected to severe loading conditions...
The system of carbon fibre-reinforced plastics micro-tubes for self-healing of glass fibre-reinforced plastics laminates
2016
A system of pultruded carbon fibre-reinforced plastics micro-tubes is used for self-healing simulation in laminated polymer composite. The system consists of a package of micro-tubes, placed in the symmetry plane of the GFR/epoxy laminate stack. Healing agent is a mixture of the epoxy resin and hardener. The healing agent releases and penetrates into the cracks after the composite is damaged by the quasi-static indentation. The specimens are healed at 30℃ for 24 h. Rectangular specimens notched under ASTM D2733 have been subjected to tensile test to determine interlaminar shear strength. Shear strength of specimens has been compared in three states (virgin, damaged and healed) for various …
Shear Capacity Model with Variable Orientation of Concrete Stress Field for RC Beams Strengthened by FRP with Different Inclinations
2021
A design-oriented analytical model able to evaluate the shear capacity of reinforced concrete (RC) beams strengthened with fiber-reinforced polymer (FRP) sheets or strips oriented in any direction is proposed. The formulation of the model is based on the variable-inclination stress-field approach, aiming to extend the provisions of current European standards to beams strengthened in shear using FRP. The main novelty of the model lies in taking into account the possible different inclination of steel stirrup and FRP reinforcement in determining the orientation of a compressed concrete stress field, and in shear strength evaluation, overcoming the approximation of the known models with variab…
Analytical Refinement of Sandwich Plate Bending Problem Considering Local Effects-I
1999
Analytic expressions for local flexural characteristics and stresses of sandwich panels under loading by point forces have been found. A discrete-layer model for bending of a three-layer panel with a soft filler is proposed. Contractility of a normal in the model is deduced in terms of a difference between deflections of face layers. The accountability of transverse shear in the filler and the sheets is deduced on piecewise rotation of the normal. Equations of the model having four degrees of displacement freedom are of twelfth order. The specific features of the stress from point forces in cylindrical bending are considered using the operational Laplace method with the generalized Dirac f…
A Statistical Approach to Permeability of Clustered Fibre Reinforcements
2004
The focus is set on mesoscale modelling of permeability of real fabrics used in composite manufacturing. Of particular interest is the effect of expected perturbations from perfect geometries, such as fibre bundle crimp, on the permeability. To start with, variational methods are used to calculate the permeability of individual gaps between fibre bundles. Based on this study a network of unit cells is formed enabling studies of two-and three-dimensional flow through the structure. From such an analysis the overall permeability of an arbitrary distribution of unit cell permeabilities can be calculated. Here random and controlled distributions are simulated. The former is an approximate repr…