Search results for "construct"
showing 10 items of 3723 documents
Computational Study of Failure of Hybrid Steel Trussed Concrete Beams
2017
This study investigates the failure behavior of hybrid steel trussed concrete beams (HSTCBs) under three-point bending through a series of finite-element (FE) simulations. The FE model employs well-established constitutive relations of concrete and steel with a simplified contact condition between the concrete and steel truss. The numerical model is compared with existing experimental data as well as a FE model that uses a more sophisticated concrete-steel interfacial model. The comparison shows that the present model is able to capture various failure mechanisms of the beam and its peak load capacity. The model is applied to investigate the behavior of a set of HSTCBs of different sizes, w…
Flexural and Shear Resistance of Steel Fiber–Reinforced Lightweight Concrete Beams
2014
In the present paper an analytical model is proposed that is able to determine the shear resistance of lightweight reinforced concrete beams with longitudinal bars, in the presence of reinforcing steel fibers. The model is based on the evaluation of the resistance contribution resulting from beam and arch actions. For the resistance contribution of main bars in tension, the residual bond adherence of steel bars and the crack spacing of reinforced concrete (RC) beams in the presence of fibers are considered. The contribution in terms of postcracking resistance in the tension zone of the beams is also included. The model was verified on the basis of experimental data available in the literatu…
An Ising ferromagnet with an antiferromagnetic surface layer: A simple model for magnetic surface reconstruction
1985
Simple cubic Ising lattices are studied by Monte Carlo simulation, using a thin film geometry (usually 40 atomic layers thick), with nearest neighbour ferromagnetic exchange J in the bulk and nearest neighbour antiferromagnetic interaction Js between surface spins. Applying a technique of preferential sampling in the surface layers, we investigate the ordering for a variety of values of JsJ and for various temperatures. For JsAF < Js < − 0.25J (where JsAF ≈ − 2.01J) ferromagnetic ordering occurs at a higher temperature than the antiferromagnetic surface ordering, while for − 0.25J < Js no antiferromagnetic long range order is possible. For Js < JsAF the surface transition occurs at a higher…
A strategy for the finite element modeling of FRP-confined concrete columns subjected to preload
2018
Abstract Compressive behavior of columns strengthened by means of an outer elastic confinement provided e.g. by fiber-reinforced polymer (FRP) jackets has become a main topic in the field of structural retrofitting. In details, the problem of the response assessment of strengthened columns is still under study. Many analytical formulations have been proposed to describe the compressive behavior of confined concrete under both monotonic and cyclic loads. However, the effect of a stress/strain level in the columns already present prior to apply the confinement has been generally neglected until now, also because of the lack of well defined strategies of modeling. In this frame, here, (1) a FE…
Analytical stress-strain law of FRP confined masonry in compression: Literature review and design provisions
2017
Abstract The use of Fibre Reinforced Polymer (FRP) wraps has become common in practical applications to retrofit existing columns with poor structural features. Wrapping the member with one or more FRP sheets makes it possible to induce confinement action and enhance strength and ductility. This application has been widely studied and adopted in reinforced concrete members for about twenty years, while its suitability to masonry columns and piers has been investigated during the last decade. The results of several studies were summarized in different design expressions for calculating effective confinement pressure, ultimate compressive stress and strain, and the overall trend of the stress…
Evolution of grain-size distribution of pumice sands in 1-D compression
2016
Abstract Crushing is one of the micromechanisms that govern the mechanical behaviour of sands at medium-high stresses. It depends on mineralogy, form and strength of single particle, mean stress level, coordination number, time, etc.. It causes changes of grain-size distribution, porosity, number and type of grain contacts, fabric, structure of the material, etc.. Results of an experimental research on the crushing of pumice sands compressed under 1-D conditions to vertical effective stresses σ′v up to 100MPa are reported here. They show marked crushing already at σ′v of about 200kPa. The evolution of the grain-size distribution can be represented by ΔDi= h/(K(1+C exp(–hlgσ′v))) in which ΔD…
Formulation of a truss element for modelling the tensile response of FRCM strips
2022
Modelling the tensile behaviour of Fabric Reinforced Cementitious Matrix (FRCM) is not a straightforward task due to the inner complexity of the mechanics of this kind of composite materials. In fact, after that the matrix is cracked, the compatibility between the fibre and the surrounding mortar is lost and the system behaves as two separate elements connected by a brittle interface. For this reason, several research studies proposed computational approaches for evaluating the tensile behaviour of FRCM composites, usually referring to brick-based 3D Finite Element Models (FEM) or to complex numerical procedures. This paper shows the formulation of a simplified coupled truss element for mod…
Laminated Glass Members in Compression: Experiments and Modeling
2014
It is well known that structural glass members are made by assembling thin laminated panels, which can be connected with different bonding techniques; for instance, with steel devices or with structural adhesives. The latter are very commonly used because they do not reduce the transparency of the member and make it possible to avoid stress concentrations because of the presence of holes. This technique is used to make up columns in glazing structures and different applications of the technique can be found in contemporary architecture. As evidenced by the literature, one of the most important problems in such members is caused by buckling phenomena, resulting from the slenderness of the pa…
Cohesive delamination and frictional contact on joining surface via XFEM
2018
In the present paper, the complex mechanical behaviour of the surfaces joining two different bodies is analysed by a cohesive-frictional interface constitutive model. The kinematical behaviour is characterized by the presence of discontinuous displacement fields, that take place at the internal connecting surfaces, both in the fully cohesive phase and in the delamination one. Generally, in order to catch discontinuous displacement fields, internal connecting surfaces (adhesive layers) are modelled by means of interface elements, which connect, node by node, the meshes of the joined bodies, requiring the mesh to be conforming to the geometry of the single bodies and to the relevant connectin…
Asphalt surface mixtures with improved performance using waste polymers via dry and wet processes
2017
"Published online: June 29, 2017"