Search results for "cooling"

Physical Cross Links in Amorphous PET, Influence of Cooling Rate and Ageing

2003

A Continuous Cooling Transformation (CCT) procedure can be used to distinguish the initial “state” of the amorphous PET samples produced upon solidification from the melt at different cooling rates. The material frozen at this stage behaves as a rubber when brought above the Tg due to the onset of physical cross links. The rubber is not a stable network, however, since physical cross links may eventually dissolve. Their size distribution, and possibly their number, depend on cooling rate and ageing. Some may be even stable above the glass transition and act as nuclei for further crystallization from the glass. Upon increasing cooling rate, size distribution becomes smaller and stability of …

Localized Motion in Supercooled Glycerol as Measured by 2 H-NMR Spin-Lattice Relaxation and Incoherent Neutron Scattering

1991

Selectively deuterated glycerol has been subjected to 2H-NMR spin-lattice relaxation and quasi-elastic neutron scattering experiments. The measurements yield relaxation rates and a non-Gaussian Q-dependence of the Debye-Waller factor which are different for the two hydrogen sites. The data analysis shows that below the onset of the glass transition α-process the hydrogens perform a local motion (≈ 10-12 s) in addition to what is expected from harmonic phonons. The resulting mean-square displacements are highly temperature dependent but are significantly smaller than those found in van der Waals glasses. Amplitudes and activation energies of the carbon-bonded and oxygen-bonded hydrogens are …

Revising midlatitude summer temperatures back to A.D. 600 based on a wood density network

2015

Annually resolved and millennium-long reconstructions of large-scale temperature variability are primarily composed of tree ring width (TRW) chronologies. Changes in ring width, however, have recently been shown to bias the ratio between low- and high-frequency signals. To overcome limitations in capturing the full spectrum of past temperature variability, we present a network of 15 maximum latewood density (MXD) chronologies distributed across the Northern Hemisphere extratropics. Independent subsets of continental-scale records consistently reveal high MXD before 1580 and after 1910, with below average values between these periods. Reconstructed extratropical summer temperatures reflect n…

Open cycles: Solid and Liquid based Desiccant Systems

2008

A macroscale FEM-based approach for selective laser sintering of thermoplastics

2017

A numerical approach to model the selective laser sintering (SLS) of polypropylene is proposed. A 3D thermal model was developed and thus enables the prediction of the temperature fields and the extension of the sintered area in the powder bed taking into account the phase change during multiple laser passes. Powder–liquid, liquid–solid and solid–liquid phase changes were modelled during the SLS and the subsequent cooling processes. Then, a 3D thermomechanically coupled model was set up based on the temperature results of the thermal model in order to predict the distortion of the produced parts after cooling down. Different pre-heating temperatures were considered, highlighting their…

Replica-exchange molecular dynamics simulation for supercooled liquids

2000

We investigate to what extend the replica-exchange Monte Carlo method is able to equilibrate a simple liquid in its supercooled state. We find that this method does indeed allow to generate accurately the canonical distribution function even at low temperatures and that its efficiency is about 10-100 times higher than the usual canonical molecular dynamics simulation.

A novel renewable system supplying energy and water to the island of Pantelleria

2016

In this paper a thermoeconomic analysis of a novel hybrid Renewable Polygeneration System connected to a district heating and cooling network is presented. The plant is powered simultaneously by solar and geothermal energy and capable to supply electricity, desalinated water, heat and cooling energy. System layout includes a Parabolic Through Collector (PTC) field, geothermal wells, an Organic Rankine Cycle (ORC) unit and a Multi-Effect Desalination (MED) system. A model of a typical building of Pantelleria urban area and a heating and cooling system based on fan coils have been modelled and linked to the plant model in TRNSYS environment. A detailed system control has been implemented in t…

Evidence of Mechanisms Occurring in Thermally Induced Phase Separation of Polymeric Systems

2014

Thermally induced phase separation is a fabrication technique for porous polymeric structures. By means of easy-to-tune processing parameters, such as system composition and demixing temperature, a vast latitude of average pore dimensions, pore size distributions, and morphologies can be obtained. The relation between demixing temperature and morphology was demonstrated via cloud point curve measurement and foams fabrication with controlled thermal protocols, for the model system poly-l-lactide–dioxane–water. The morphologies obtained at a temperature lower than cloud point showed a closed-pore architecture, suggesting a “nucleation-and-growth” separation mechanism, which produced larger po…

Assessing the feasibility of cogeneration retrofit and district heating/cooling networks in small Italian islands

2017

Sustainability of energy supply strategies in small islands has been emerging as a severe issue, due to the large margins for improvement and rationalization of the most frequently adopted solutions. In most of the European islands, large amounts of heat are wasted by the operation of engine-based power plants; conversely, heat is produced by boilers (supplied by liquid fuels) or by electric equipment for a number of different uses, like domestic hot water production or space heating in winter. In this paper a techno-economic analysis is proposed to assess the feasibility of CHP-retrofit of the existing power plants and the possible utilization of the recovered heat to supply, via a distric…

Thermal-hydraulic behaviour of the DEMO divertor plasma facing components cooling circuit

2017

Abstract Within the framework of the Work Package DIV 1 – “Divertor Cassette Design and Integration” of the EUROfusion action, a research campaign has been jointly carried out by ENEA and University of Palermo to investigate the thermal-hydraulic performances of the DEMO divertor cassette cooling system. A comparative evaluation study has been performed considering three different options for the cooling circuit layout of the divertor Plasma Facing Components (PFCs). The potential improvement in the thermal-hydraulic performance of the cooling system, to be achieved by modifying cooling circuit layout, has been also assessed and discussed in terms of optimization strategy. The research acti…