Search results for "digital signal"
showing 10 items of 70 documents
Analysis a DSP Implementation and Experimental Validation of a Loss Minimization Algorithm Applied to Permanent Magnet Synchronous Motor Drives
2004
In this paper a new loss minimization control algorithm for inverter-fed permanent-magnet synchronous motors (PMSM), which allows to reduce the power losses of the electric drive without penalty on its dynamic performances, is analyzed, experimentally realized and validated. In particular, after a brief recall of two loss minimization control strategies (the "search control" and the "loss-model control"), both a modified dynamic model of the PMSM, which takes into account the iron losses, and a "loss-model" control strategy, are treated. Experimental tests on a specific PMSM drive employing the proposed loss minimization algorithm were performed aiming to validate the actual implementation.…
Digital filtering and analysis for a semiconductor X-ray detector data acquisition
2007
Abstract Pile-up distortion is a major drawback in X-ray spectroscopy at high count rate. Pulse width narrowing with shaping techniques can lead to the reduction of the pile-up distortion, but a low shaping time reduces the noise filtration and leads to a poor energy resolution. Thus, only a best compromise solution between the pile-up and the noise requirements is achievable. The hardware manipulation needed to adjust the parameters of the traditional electronic shaping amplifiers makes it uneasy to tests various settings in different conditions. Digital techniques can help to overcome such difficulties. A digital signal processing and analysis system for X-ray spectroscopy is described in…
Implementation of pattern recognition algorithm based on RBF neural network
2002
In this paper, we present implementations of a pattern recognition algorithm which uses a RBF (Radial Basis Function) neural network. Our aim is to elaborate a quite efficient system which realizes real time faces tracking and identity verification in natural video sequences. Hardware implementations have been realized on an embedded system developed by our laboratory. This system is based on a DSP (Digital Signal Processor) TMS320C6x. The optimization of implementations allow us to obtain a processing speed of 4.8 images (240x320 pixels) per second with a correct rate of 95% of faces tracking and identity verification.
Muon identification with the ATLAS Tile Calorimeter Read-Out Driver for Level-2 trigger purposes
2008
The Hadronic Tile Calorimeter (TileCal) at the ATLAS experiment is a detector made out of iron as passive medium and plastic scintillating tiles as active medium. The light produced by the particles is converted to electrical signals which are digitized in the front-end electronics and sent to the back-end system. The main element of the back-end electronics are the VME 9U Read-Out Driver (ROD) boards, responsible of data management, processing and transmission. A total of 32 ROD boards, placed in the data acquisition chain between Level-1 and Level-2 trigger, are needed to read out the whole calorimeter. They are equipped with fixed-point Digital Signal Processors (DSPs) that apply online …
Portable Video Supercomputing
2004
As inexpensive imaging chips and wireless telecommunications are incorporated into an increasing array, of portable products, the need for high efficiency, high throughput embedded processing will become an important challenge in computer architecture. Videocentric applications, such wireless videoconferencing, real-time video enhancement and analysis, and new, immersive modes of distance education, will exceed the computational capabilities of current microprocessor and digital signal processor (DSP) architectures. A new class of embedded computers, portable video supercomputers, will combine supercomputer performance with the energy efficiency required for deployment in portable systems. …
Digital signal processing for rail monitoring by means of ultrasonic guided waves
2007
Recent train accidents have reaffirmed the need for developing rail defect detection systems that are more effective than those used today. One of the recent developments in rail inspection is the use of ultrasonic guided waves (UGWs) and non-contact probing techniques to target transverse-type defects. Besides the obvious advantages of non-contact probing, that include robustness and a potential for large inspection speed, such a system can theoretically detect transverse defects under horizontal shelling or head checks. This paper demonstrates the effectiveness of digital signal processing to enhance the damage detection sensitivity of the non-contact system. The method proposed here comb…
A DSP-Based Resolver-To-Digital Converter for High-Performance Electrical Drive Applications
2016
This paper presents a low cost, simple, and highly accurate resolver-to-digital converter (RDC) for electrical drive applications based on an integrated software approach, thus allowing a significant reduction of hardware components count with significant improvements in terms of reliability, reduction of fault rate, and susceptibility to electromagnetic interference (EMI). Particular attention has been addressed to cost which is 25% off over conventional RDC. Simulations and experimental tests confirm the high quality of the proposed system.
Design And Characterization Of Automated Color Sensor System
2017
Abstract The paper presents a color sensor system that can process light reflected from a surface and produce a digital output representing the color of the surface. The end-user interface circuit requires only a 3-bit pseudo flash analog-to-digital converter (ADC) in place of the conventional/typical design comprising ADC, digital signal processor and memory. For scalability and compactness, the ADC was designed such that only two comparators were required regardless of the number of color/wavelength to be identified. The complete system design has been implemented in hardware (bread board) and fully characterized. The ADC achieved less than 0.1 LSB for both INL and DNL. The experimental r…
A New Digital Demodulator for Sensorless Control of Electrical Drives with Permanent Magnet Synchronous Motors
2008
This paper deals a new digital demodulator algorithm for sensorless control of interior permanent magnet synchronous motors (IPMS) based on the estimation of speed and rotor angular position. To this aim a signal similar to that generated by a resolver connected to the shaft of the motor is obtained injecting high frequency stator currents. A new digital algorithm has been designed and set up to demodulate the above signal whose implementation can be carried out on the same DSP that processes the whole control algorithm. The proposed demodulator scheme is presented and justified on the theoretic point of view. Simulations results finally validate the effectiveness of the demodulator within …
Guidelines for the design and implementation of the ARPCC control applied to grid-connected converters
2013
Abstract This paper presents implementation details of the adaptive robust predictive current control (ARPCC) applied to a grid-connected converter, such as feed-forward cancellation protocol, the selection of the observer gain and adaptive parameters or the sampling options, needed to get the best performance of this control. The feed-forward term cancellation permits to achieve a very low harmonic distortion in current waveforms when the voltage sensing circuits are well calibrated. A detailed gain adjustment protocol of the voltage sensing circuits is presented in this paper. Moreover, a control design procedure based on the observer gain L o boundaries and the adaptive parameters has be…