Search results for "displacement"

Steel-concrete bond in lightweight fiber reinforced concrete under monotonic and cyclic actions

2005

Experimental results of the local bond stress-slip relationship of reinforcing bars embedded in lightweight fiber reinforced concrete with expanded clay aggregates are presented. The effect of the following parameters were investigated: - dimension of specimens; - anchorage length; - percentages of hooked steel fibers; - geometrical ratio of transverse reinforcement; - confinement external transverse pressure. Prismatic specimens with deformed steel bars embedded for a fixed length equal to five and eight equivalent diameters were tested under both monotonic and cyclic reversal imposed displacements at the tip of the bars, in controlled displacement tests. The influence of the above mention…

Back EMF Sensorless-Control Algorithm for High-Dynamic Performance PMSM

2010

In this paper, a low-time-consuming and low-cost sensorless-control algorithm for high-dynamic performance permanent-magnet synchronous motors, both surface and internal permanent-magnet mounted for position and speed estimation, is introduced, discussed, and experimentally validated. This control algorithm is based on the estimation of rotor speed and angular position starting from the back electromotive force space-vector determination without voltage sensors by using the reference voltages given by the current controllers instead of the actual ones. This choice obviously introduces some errors that must be vanished by means of a compensating function. The novelties of the proposed estima…

One My scale subsidence of carbonate sedimentary bodies and the viscosity of the lower crust

2004

Abstract The possibility of flow of the lower crust under the load produced by carbonate sedimentary accumulations is investigated through the example of the Paris basin during the Middle Jurassic (i.e. Bathonian). Depositional geometries, water depths and sedimentary environments have been estimated and correlated for 164 sites spread over a surface of 380 per 220 km for three successive periods lasting each less than 0.8 My. A signal of relative vertical displacement has been extracted from water-depth and sedimentary thickness. Data have then been interpolated to produce maps of velocity of vertical displacement, sedimentation rate, water depth, and water-depth variation between two peri…

Static instability analysis for travelling membranes and plates interacting with axially moving ideal fluid

2010

The out-of-plane instability of a moving plate, travelling between two rollers with constant velocity, is studied, taking into account the mutual interaction between the buckled plate and the surrounding, axially flowing ideal fluid. Transverse displacement of the buckled plate (assumed cylindrical) is described by an integro-differential equation that includes the centrifugal force, the aerodynamic reaction of the external medium, the vertical projection of membrane tension, and the bending force. The aerodynamic reaction is found analytically as a functional of the displacement. To find the critical divergence velocity of the moving plate and its corresponding buckling mode, an eigenvalue…

Perturbations of symmetric elliptic Hamiltonians of degree four

2006

AbstractIn this paper four-parameter unfoldings Xλ of symmetric elliptic Hamiltonians of degree four are studied. We prove that in a compact region of the period annulus of X0 the displacement function of Xλ is sign equivalent to its principal part, which is given by a family induced by a Chebychev system; and we describe the bifurcation diagram of Xλ in a full neighborhood of the origin in the parameter space, where at most two limit cycles can exist for the corresponding systems.

Diffusion of colloids in one-dimensional light channels

2004

Single-file diffusion (SFD), prevalent in many chemical and biological processes, refers to the one-dimensional motion of interacting particles in pores which are so narrow that the mutual passage of particles is excluded. Since the sequence of particles in such a situation remains unaffected over time t, this leads to strong deviations from normal diffusion, e.g. an increase of the particle mean-square-displacement as the square root of t. We present experimental results of the diffusive behaviour of colloidal particles in one-dimensional channels with varying particle density. The channels are realized by means of a scanning optical tweezers. Based on a new analytical approach (Kollmann 2…

In silico, spectroscopic, and biological insights on annelated pyrrolo[3,2-e]pyrimidines with antiproliferative activity

2013

The in silico COMPARE analysis was performed on 8-[3-(piperidino)propyl]-4,10-dimethyl-9-phenyl-6-(methylsulfanyl)-3,4-dihydropyrimido[1,2-c]pyrrolo[3,2-e]pyrimidin-2(8H)-one, a compound with promising antiproliferative activity, previously synthetized and screened against a panel of 60 human tumor cell lines. The results evidenced that this compound matches the biological properties of Chromomycin A3 and Actinomycin D, known drugs with high DNA binding affinity. Prompted by such results, a thorough spectroscopic investigation of its DNA aqueous solutions was performed, with the aim to verify its DNA-binding properties. DNA groove-binding interaction was assigned by UV-vis spectrophotometri…

Non-porous microparticulate supports in high-performance liquid chromatography (HPLC) of biopolymers — concepts, realization and prospects

1986

A symmetric tangent stiffness approach to cohesive mechanical interfaces in large displacements

2022

The present article proposes a formulation for a cohesive interface element in large displacement conditions. Theoretical and computational aspects, useful for an effective and efficient finite element implementation, are examined in details. A six-node (or higher) isoparametric interface element for two dimensional cohesive fracture propagation problems is developed. The element operators are consistently derived by a variational approach enforced in the current configuration, where a current frame is defined with axes tangential and normal to the middle line of the interface opening displacement gap. Under the constitutive assumption of small value of the modulus of the vector product bet…

Extended constrained deformations: a new sculpturing tool

1999

Modelling tools tend to virtual sculpturing, in which a basic object is deformed by user supplied actions. The model we present aims to be generic: whatever the geometric description of the object, we can deform it to satisfy location constraints. Our model deforms the whole space, the image of a point is a blend of deformation functions with a projection matrix which allows the satisfaction of the constraints. The user can define the extent of the deformation (i.e. the part of the object to be deformed), the shape of the deformation function to create profiles and the displacement of the constraint points to be satisfied.