Search results for "dynamics"

Experimental organic matter maturation at 2kbar: Heat-up effect to low temperatures on vitrinite reflectance

2012

Abstract An experimental study was performed to evaluate the effect of heat-up to various low temperatures on vitrinite reflectance ( VR ) at 2 kbar employing the same previously used heat-up procedures, starting material and apparatus. Heat-up is the isobaric experimental procedure consisting of the increase in temperature of the laboratory vitrinite maturation from room temperature to the desired run temperature T end of heat-up at which the isobaric-isothermal maturation starts. Experiments employed cold-seal pressure vessels with classical heat-up devices and were carried out on wet (water added) xylite of swamp cypress. Confined system maturation experiments were conducted at 2 kbar an…

Vapor–liquid equilibria in dendrimer and hyperbranched polymer solutions: experimental data and modeling using UNIFAC-FV

2004

Abstract This work evaluates the potential of the group contribution method universal functional activity coefficients-free-volume (UNIFAC-FV) to predict vapor–liquid equilibria (VLE) in dendrimer-solvent and hyperbranched polymer-solvent systems. The VLE of hydroxyl-functional dendritic polymers (polyethers, polyesters, polyamidoamine), dissolved in polar solvents (ethanol and/or water) are studied both experimentally and theoretically. A new approach is suggested to account for the contribution of selected types of polymer structural units (i.e. linear, dendritic and terminal units) to the solvent residual activity. The results of calculations are in a good agreement with experiment. Furt…

Frontispiece: Hierarchy of Asymmetry at Work: Chain-Dependent Helix-to-Helix Interactions in Supramolecular Polymers

2018

LARGE DEFORMATION CREEP BEHAVIOR OF A SOLID POLYMER.

1981

Abstract The effect of loading rate and strain on the creep behavior after sample yielding has been studied in previous communications (14–15) for Mylar in tension and for Lexan in compression. In this work the creep behavior of Lexan samples previously elongated is considered both in tension and in compression. A procedure which collects all the data independently of both loading rate and initial creep strain is proposed.

Influence of“controlled processing conditions” on the solidification of iPP, PET and PA6

2002

In this work reliable experimental data for three semicrystalline polymers (iPP, PA6, PET) crystallised under pressure and high cooling rates are supplied. These results were achieved on the basis of a model experiment where drastic controlled solidification conditions are applied. The final objective was to quantify the effect of two typical operating conditions (pressure and cooling rate) on the final properties and morphology of the obtained product. The influence of processing conditions on some macroscopically relevant properties, such as density and micro hardness is stressed, together with the influence of processing conditions on the product morphology, investigated by means of Wide…

The use of the indentation test for studying the solidification behaviour of different semicrystalline polymers during injection moulding

2005

Summary: An in-line method for monitoring the solid-ificationprocess during injection molding of semicrystallinepolymers (demonstrated previously in J. Appl. Polym. Sci.2003, 89, 3713) is based on a simple device, where anadditional ejector pin is pushed on the injection molded partatdifferenttimesduringthesolidificationphase.The‘inden-tation depth profile’, i.e., residual deformation as a functionoftime,wasobtainedandallowedtodeterminetheevolutionof the solidification front in the mold as a function of thecooling time. The present work shows the reliability andthe powerfulness of the aforementioned method for a largevariety of different semicrystalline polymers (PET, PBT,polyamide-6 PA6, isota…

Deformation recovery behavior of a solid polymer after tensile yielding

1984

In this work the deformation recovery behavior of an amorphous polymer after large tensile deformation is studied at different temperatures. The effect of three parameters other than temperature has been pointed out in previous works (1–3).

Deformation recovery behaviour of a solid polymer after tensile yielding

1987

In this work the deformation recovery behavior of an amorphous polymer after large tensile deformation is studied at different temperatures. The effect of three parameters other than temperature has been pointed out in previous works (1–3). The data here presented indicate that the influence of all parameters, including temperature, on recovery behavior can be related to the residual stress, σ *, at the beginning of recovery test. This suggests to plot the recovery versus time curves, relative to different sets of parameters including temperature, by means of the same normalizing groups which were adopted in (2), thus shifting all curves towards a single master curve.

A new equipment to measure the combined effect of humidity, temperature, mechanical stress and UV exposure on the creep behaviour of polymers

2008

To be able to study and predict the physical properties of a polymeric material under different environmental conditions is very important. Moisture, UV irradiation, thermal and mechanical stresses can dramatically change the characteristics of the material and hinder some specific applications. In this work, a new equipment able to perform creep tests under different environmental conditions (temperature, humidity, stress) is presented. Some preliminary results are also presented using a sample of polyamide 6. As this polymer is sensitive to all these variables, it is appropriate to verify the effectiveness of the new instrument.

Viscoelastic recovery behavior following Atomic Force Microscope nanoindentation of semi-crystalline poly(ethylene)

2007

The residual imprint left behind by the AFM nanoindentation of polymers has been seldom studied in the past. In this work, the evolution of indentations at room temperature performed on a semicrystalline poly- (ethylene) in a broad range of experimental conditions is presented. The study shows that the recovery after 24 h is substantial, although not complete. Moreover, the dynamics of the recovery process is not seen to depend on the magnitude of the applied load for the nanoindentation, but instead on the rate of the indentation used. This points out that viscoelastic processes are minimized when performing fast nanoindentations, while at low loading rates there seems to be a residual vis…