Search results for "edge"
showing 10 items of 3866 documents
Quadratic nonlinear optical parameters of 7% MgO-doped LiNbO3 crystal
2016
International audience; Pure and 7% MgO-doped lithium niobate (LiNbO3) single crystals were grown by the Czochralski technique. The shift of optical absorption edge in 7% MgO-doped crystal in direction of shorter wavelength compared to undoped crystal was observed. The second harmonic generation measurements of 7% MgO-doped LiNbO3 crystal were performed at room temperature by means of the rotational Maker fringe technique using Nd:YAG laser generating at 1064 nm in picoseconds regime. Experimentally obtained value of nonlinear optical coefficient d33 for 7% MgO-doped LiNbO3 was found to be less than for undoped crystal but higher than for 5% MgO-doped. I-type phase-matched second harmonic g…
Spectroscopic characterization of non-covalent CuPc-GO system. Experiment and theory
2019
Abstract In this study we report on UV-vis, IR and Raman studies of non-covalent copper phthalocyanine (CuPc) – flake graphene oxide (GO) complex in water and in the solid phase. Experimental results were supported by molecular modeling of structure, electronic and vibrational parameters for free CuPc and its 1 : 1 complexes with water, benzene, phenol, neutral and deprotonated benzoic acid. HOMO-LUMO gaps for these complexes were calculated and compared with data derived from the absorption edge of Q-band in the recorded UV-vis spectra for free CuPc and its adduct with GO in water. Small but non-negligible changes in position of spectral bands observed as result of CuPc interaction with GO…
Formation of Gold(I) Edge Oxide at Flat Gold Nanoclusters on an Ultrathin MgO Film under Ambient Conditions
2010
Many active gold catalysts are prepared onreducible oxides, and strong interactions between the supportand the gold particle may create active sites at the peripheryclose to the particle–support interface. These interactionsmay also include charge transfer to or from the particle. Forpurely geometric reasons, small particles have a high propor-tion of low-coordinated edge and corner atoms that might actas reaction centers. Also, thermal effects from localized softphonon modes at particle edges may contribute to thelowering of critical reaction barriers.Lately, a large amount of work has been conducted toelucidate the properties of gold clusters on ultrathin (a fewmonolayers (ML) thick) MgO …
Insight into the defect-molecule interaction through the molecular-like photoluminescence of SiO2 nanoparticles
2016
Luminescence properties due to surface defects in SiO2 are the main keystone with particles that have nanoscale dimensions, thus motivating their investigation for many emission related applications in the last few decades. A critical issue is the role played by the atmosphere that, by quenching mechanisms, weakens both the efficiency and stability of the defects. A deep knowledge of these factors is mandatory in order to properly limit any detrimental effects and, ultimately, to offer new advantageous possibilities for their exploitation. Up to now, quenching effects have been interpreted as general defect conversion processes due to the difficulty in disentangling the emission kinetics by…
Luminescence mechanisms of defective ZnO nanoparticles.
2016
ZnO nanoparticles (NPs) synthesized by pulsed laser ablation (PLAL) of a zinc plate in deionized water were investigated by time-resolved photoluminescence (PL) and complementary techniques (TEM, AFM, μRaman). HRTEM images show that PLAL produces crystalline ZnO NPs in wurtzite structure with a slightly distorted lattice parameter a. Consistently, optical spectra show the typical absorption edge of wurtzite ZnO (Eg = 3.38 eV) and the related excitonic PL peaked at 3.32 eV with a subnanosecond lifetime. ZnO NPs display a further PL peaking at 2.2 eV related to defects, which shows a power law decay kinetics. Thermal annealing in O2 and in a He atmosphere produces a reduction of the A1(LO) Ra…
Synthesis of multi-color luminescent ZnO nanoparticles by ultra-short pulsed laser ablation
2020
Abstract Crystalline ZnO nanoparticles (NPs) are synthesized by ultra-short femtosecond (fs) pulsed laser ablation (PLA) of a zinc plate in deionized water, and are investigated by optical absorption and time resolved luminescence spectra in combination with the morphology and structure analysis. The comparison with previous experiments based on short nanosecond (ns) PLA highlights that pulse duration is a crucial parameter to determine the size and the optical properties of ZnO NPs. While short PLA generates NPs with average size S ‾ of ~ 30 nm, ultrashort PLA allows to achieve much smaller NPs, S ‾ ⩽ 10 nm, that evidence weak quantum confinement effects on both the absorption edge and th…
Generation and excitation of point defects in silica by synchrotron radiation above the absorption edge
2010
We report photoluminescence measurements carried out on amorphous SiO{sub 2} upon excitation by synchrotron light. Exposure of the as-grown material to above-edge light at low temperature induces the formation of nonbridging oxygen hole centers (NBOHC), localized in a thin layer below the surface limited by the penetration depth (tens of nm) of impinging light. After concluding the exposure to 11 eV light, stable defects are revealed by observing their characteristic 1.9 eV photoemission band excited at 4. 8eV. The local concentration of induced defects, supposedly formed by nonradiative decay of excitons, is very high (close to approx10{sup 21} cm{sup -3}) and independent of the previous h…
Tribology of Metal Cutting
2008
This chapter provides comprehensive knowledge regarding tribological behaviour of the cutting zone and characterizes specific features of the tool–chip contact that influence friction mechanisms in this area. Adhesion, plastic deformation of contacting asperities and ploughing action of the cutting edge are selected as three predominant mechanisms controlling sliding friction between the tool and the chip. The two-zone model of the tool–chip contact distinguishing seizure and sliding regions is characterized, along with experimental evidence based on photoelastic and material flow line techniques. Corresponding stress distributions for plane and restricted-contact cutting tools are provided…
Dislocation interaction with C in α-Fe: a comparison between atomic simulations and elasticity theory
2008
International audience; The interaction of C atoms with a screw and an edge dislocation is modelled at an atomic scale using an empirical Fe-C interatomic potential based on the Embedded Atom Method (EAM) and molecular statics simulations. Results of atomic simulations are compared with predictions of elasticity theory. It is shown that a quantitative agreement can be obtained between both modelling techniques as long as anisotropic elastic calculations are performed and both the dilatation and the tetragonal distortion induced by the C interstitial are considered. Using isotropic elasticity allows to predict the main trends of the interaction and considering only the interstitial dilatatio…
Surface and interface analysis of worn TiN (PVD) coated cold forging tools
1992
Abstract Wear of cold forging tools, improved by TiN (PVD) hard coating and used in the production of alternator and starter components in the car industry, has been studied in detail. The most complicated case was the tool that produced a clutch housing of high precision. The 630 kN press process (50 pcs min −1 ) caused heavy adhesive and abrasive wear due to material flow, high surface pressure and also wear in the direction of tool movement. Results show that on the worn functional surfaces of the analysed tool, the lifetime of which was extended with TiN coating by a factor of 8–10, the following features were observed: non-uniform TiN coating thickness decrease; long grooves, damaged a…