Search results for "efficien"

Acoustic methods for measuring the porosities of porous materials incorporating dead-end pores

2013

International audience; The acoustic properties of porous materials containing dead-end (DE) pores have been proposed by Dupont et al. [J. Appl. Phys. 110, 094903 (2011)]. In the theoretical description, two physical parameters were defined (the dead-end porosity and the average length of the dead-end pores). With the knowledge of the open porosity (measured with non-acoustic methods), and the measurement of kinematic porosity (also called the Biot porosity in this article), it is possible to deduce the dead-end porosity. Two acoustic methods for measuring the Biot porosity for a wide range of porosities are proposed. These methods are based on acoustic transmission and on the low and high …

Respiratory mechanics measured by forced oscillations during mechanical ventilation through a tracheal tube

2011

The forced oscillation technique (FOT) allows the measurement of respiratory mechanics in the intensive care setting. The aim of this study was to compare the FOT with a reference method during mechanical ventilation through a tracheal tube. The respiratory impedance spectra were measured by FOT in nine anaesthetized pigs, and resistance and compliance were estimated on the basis of a linear resistance-compliance inertance model. In comparison, resistance and compliance were quantified by the multiple linear regression analysis (LSF) of conventional ventilator waveforms to the equation of motion. The resistance of the sample was found to range from 6 to 21 cmH(2)O s l(-1) and the compliance…

400– to 1000–nm imaging spectrometer based on acousto-optic tunable filters

2004

An imaging spectrometer covering the 400-1000 nm band has been conceived and developed. The system is based on an Acousto-Optic Tunable Filter (AOTF) attached to a high performance digital camera. The AOTF permits the selection of spectral bands with an RF signal in the range of 70-210 MHz. The range is covered using two transducers attached to a single crystal. Although the idea is not new it covers a broader spectrum than previous systems. It includes a telecentric optical system that enhances system efficiency, by ensuring that the chief ray of each light cone emerges out of this doublet parallel to the optical axes. Additionally, an smart choice of integration time reduces the dependenc…

Influence of the evolutionary optimization parameters on the optimal topology

2016

Topological optimization can be considered as one of the most general types of structural optimization. Between all known topological optimization techniques, the Evolutionary Structural Optimization represents one of the most efficient and easy to implement approaches. Evolutionary topological optimization is based on a heuristic general principle which states that, by gradually removing portions of inefficient material from an assigned domain, the resulting structure will evolve towards an optimal configuration. Usually, the initial continuum domain is divided into finite elements that may or may not be removed according to the chosen efficiency criteria and other parameters like the spee…

Experimental Comparative Analysis of Efficiency and THD for a Three-phase Five-level Cascaded H-Bridge Inverter Controlled by Several MC-PWM Schemes

2021

Cascaded H-Bridges Multilevel Inverters are an innovative and promising solution in different application fields. This topology allows obtaining an improvement in the performance (e.g. reduced harmonic content, the low voltage stress on power components, and high efficiency) in respect to the traditional two-level inverters. In this context, the Multicarrier-PWM strategies play an important role thanks to their features. This paper presents an experimental investigation on the performance of a three-phase five-level Cascaded H-Bridge inverter by using different PWM modulation strategies. In particular, the paper is focused on the experimental validation of the main features of Multicarrier …

Power Conversion System for Improved Linear Generator in sea wave energy harvesting applications

2020

Nowadays, many islands worldwide are lack of electrical energy. Thus, it is convenient to exploit available renewable energy sources, among which sea waves near the islands. This paper focuses on the power conversion system coupled with an offshore wave energy device, such as an improved linear generator, to be used for sea wave energy harvesting. Particularly, the design of the linear generator has been proposed to improve the energy efficiency of the entire system. The proposed power conversion system is composed by two Boost Rectifier (BR) directly coupled to the linear generator, and one Voltage Source Inverter (VSI), which it is used as front-end between the DC-bus and the grid. The pr…

Effect of uniaxial deformation on the optical scattering losses of a semicrystalline fluorocopolymer.

1997

Both small- and wide-angle light scattering as well as transmission measurements have been used to investigate the optical scattering losses of a vinylidene difluoride–tetrafluoroethylene–hexafluoropropylene copolymer crystallized from the melt. The main origin of the scattering loss is the wide-angle light scattering from the spherulitic superstructure. Uniaxial deformation transforms this structure into a fiber morphology. The attenuation of fibers has been measured for light propagating both parallel and perpendicular to the orientation axis. For both directions, the attenuation decreases with increasing draw ratio. Annealing of the fibers while keeping their ends fixed is an effective m…

Estimation of interfacial fracture toughness based on progressive edge delamination of a thin transparent coating on a polymer substrate

2010

Evaluation of interfacial toughness of sub-micron-thickness layers deposited on a ductile substrate is a challenging task which has motivated different experimental approaches Fragmentation testing was used in the present study as a means of interface characterization of a silicon-nitride-coated polyimide substrate. During the test, after an initial rapid segmentation-cracking phase, the coating fragments developed edge delaminations which propagated in a stable manner with further increase in the applied strain The debonding process was modelled by the finite element method Incorporating a cohesive zone at the front of the interfacial crack The edge cracks were found to be dominated by mod…

Energy efficiency and CO2 emissions of port container terminal equipment: Evidence from the Port of Valencia

2019

Abstract Energy efficiency has emerged as a key point in port industry because of different factors such as the adoption of stronger environmental regulations and the increasing pressure of the local community on the surrounding ports. As gathering operational data from port terminals can be difficult due to privacy, studies on emissions and energy efficiency of these terminals are scarce. The following research provides key information about the real energy consumption and CO2 emissions of one of the most relevant container terminals in the Mediterranean area, located in Valencia, Spain. The results show that yard terminal tractors and rubber tyred gantry cranes (RTGs) are the main emissio…

2004

This paper presents the use of Support Vector Machines (SVMs) for prediction and analysis of antisense oligonucleotide (AO) efficacy. The collected database comprises 315 AO molecules including 68 features each, inducing a problem well-suited to SVMs. The task of feature selection is crucial given the presence of noisy or redundant features, and the well-known problem of the curse of dimensionality. We propose a two-stage strategy to develop an optimal model: (1) feature selection using correlation analysis, mutual information, and SVM-based recursive feature elimination (SVM-RFE), and (2) AO prediction using standard and profiled SVM formulations. A profiled SVM gives different weights to …