Search results for "electrochemical"
showing 10 items of 574 documents
Template Electrochemical Growth and Properties of Mo Oxide Nanostructures
2014
This work is aimed at studying the growing process of nanostructures electrodeposited from molybdate aqueous solutions at different pH values into pores of polycarbonate membrane templates. The challenging issue was the opportunity to investigate a rather complex deposition process in a confined ambient, where electrochemical conditions are quite different from those usually established for deposition on a flat substrate. Nanostructures were grown from a bath containing Mo7O246– (NH4)6Mo7O24·4H2O) at different concentrations (50–100 g/L), at a constant cathodic current density of 2 mA/cm2 (electrodeposition area ∼8 cm2). Nanostructured deposit was characterized by XRD, EDS, Raman, XPS, and …
Electrochemical formation of novel TiO2-ZnO hybrid nanostructures for photoelectrochemical water splitting applications
2020
[EN] In this study, hybrid ZnO-TiO2 nanostructures have been synthesised by means of a simple electrochemical anodisation of titanium and subsequently ZnO electrodeposition. The influence of Zn(NO3)(2) concentration and temperature during the electrodeposition process was evaluated. Different techniques were used to analyse the synthesised nanostructures, notably Field Emission Scanning Electron Microscopy (FE-SEM) with Energy-dispersive X-ray spectroscopy (EDX) and Confocal Microscopy with Raman spectroscopy coupled with an Atomic Force Microscope. Photoelectrochemical water splitting tests were also performed at the hybrid nanostructures. According to the results, the photoelectrochemical…
Optimizing Energy Transduction of Fluctuating Signals with Nanofluidic Diodes and Load Capacitors
2018
[EN] The design and experimental implementation of hybrid circuits is considered allowing charge transfer and energy conversion between nanofluidic diodes in aqueous ionic solutions and conventional electronic elements such as capacitors. The fundamental concepts involved are reviewed for the case of fluctuating zero-average external potentials acting on single pore and multipore membranes. This problem is relevant to electrochemical energy conversion and storage, the stimulus-response characteristics of nanosensors and actuators, and the estimation of the accumulative effects caused by external signals on biological ion channels. Half-wave and full-wave voltage doublers and quadruplers can…
Atomic scale surface modification of TiO2 3D nano-arrays: plasma enhanced atomic layer deposition of NiO for photocatalysis
2021
Here we report the development of a new scalable and transferable plasma assisted atomic layer deposition (PEALD) process for the production of uniform, conformal and pinhole free NiO with sub-nanometre control on a commercial ALD reactor. In this work we use the readily available nickel precursor nickelocene in conjunction with O2 plasma as a co-reagent (100 W) over a temperature range of 75–325 °C. An optimised growth per cycle of 0.036 nm was obtained at 250 °C with uniform thickness and coverage on scale-up to and including an 6 inch Si wafer (with a 200 nm thermal SiO2 top layer). The bulk characteristics of the NiO thin films were comprehensively interrogated by PXRD, Raman spectrosco…
Enhancement of photoconversion efficiency in dye-sensitized solar cells exploiting pulsed laser deposited niobium pentoxide blocking layers
2015
Abstract Among all the photovoltaic technologies developed so far, dye-sensitized solar cells are considered as a promising alternative to the expensive and environmentally unfriendly crystalline silicon-based solar cells. One of the possible strategies employed to increase their photovoltaic efficiency is to reduce the charge recombination at the cell conductive substrate through the use of a compact blocking layer. In this paper, we report on the fabrication and characterization of dye-sensitized solar cells employing niobium pentoxide (Nb 2 O 5 ) thin film blocking layer deposited through the pulsed laser deposition technique on conductive substrates. The careful selection of the optimal…
Study of Passive Films Formed on AISI 316L Stainless Steel in Non-Polluted and Underwater-Volcano-Polluted Seawater
2014
This work studies the semiconducting behavior of passive films formed on AISI 316L (UNS S31603) in two different sea-water solutions, non-polluted and polluted, collected from the volcano of El Hierro Island. Polarization measurements, potentiostatic passivation tests, electrochemical impedance spectroscopy, and capacitance measurements were performed. Results show that the polluted seawater worsens passivation kinetics. Additionally, passive films formed on AISI 316L stainless steel in polluted seawater have been found to be less protective than those formed in non-polluted seawater, showing a more defective structure, owing to the acidity of the polluted medium.
Mass‐Spectrometric Imaging of Electrode Surfaces—a View on Electrochemical Side Reactions
2020
Abstract Electrochemical side reactions, often referred to as “electrode fouling”, are known to be a major challenge in electro‐organic synthesis and the functionality of modern batteries. Often, polymerization of one or more components is observed. When reaching their limit of solubility, those polymers tend to adsorb on the surface of the electrode, resulting in a passivation of the respective electrode area, which may impact electrochemical performance. Here, matrix‐assisted laser‐desorption/ionization mass spectrometry (MALDI‐MS) is presented as valuable imaging technique to visualize polymer deposition on electrode surfaces. Oligomer size distribution and its dependency on the contact …
Passive Behavior and Passivity Breakdown of AISI 304 in LiBr Solutions through Scanning Electrochemical Microscopy
2014
The passive behavior and passivity breakdown of AISI 304 stainless steel in LiBr solutions has been investigated by means of scanning electrochemical microscopy (SECM). The sample generation - tip collection (SG-TC) mode was used to operate the SECM and the tip potential was biased to detect the electroactive species. The evolution of the current at the ultramicroelectrode tip with the applied potential within the passive range was followed at different LiBr concentrations. Results show that the absolute value of the current at the tip increases with the applied potential. Additionally, SECM was also used to detect stable pits formed on the stainless steel surface in a 0.2 M LiBr solution. …
Highly phosphorescent perfect green emitting iridium(iii) complex for application in OLEDs.
2007
A novel iridium complex, [bis-(2-phenylpyridine)(2-carboxy-4-dimethylaminopyridine)iridium(III)] (N984), was synthesized and characterized using spectroscopic and electrochemical methods; a solution processable OLED device incorporating the N984 complex displays electroluminescence spectra with a narrow bandwidth of 70 nm at half of its intensity, with colour coordinates of x = 0.322; y = 0.529 that are very close to those suggested by the PAL standard for a green emitter. Bolink, Henk, Henk.Bolink@uv.es ; Coronado Miralles, Eugenio, Eugenio.Coronado@uv.es ; Garcia Santamaria, Sonsoles Amor, Sonsoles.Garcia@uv.es
Temperature Effect of Ionic Transition Metal Complex Light-Emitting Electrochemical Cells
2013
ABSTRACTLight-Emitting Electrochemical Cells (LECs) consist of solution processable ionic light-emitting materials and use air stable electrodes. Their operational mechanism relies on both ionic and electronic conduction. The dynamic behavior is primarily determined by the ionic conductivity. Here, we demonstrate that with increasing temperature the LECs turn-on faster yet without decreasing the efficiency. This is due to the activation energy of ionic transport and the temperature independent photoluminescence quantum yields.