Search results for "electromagnetic"
showing 10 items of 1595 documents
Sensorless variable speed single-phase induction motor drive system
2012
It is usual find single-phase induction motor (SPIM) in several house, office, shopping, farm, and industry applications, which are become each time more sophisticated and requiring variable speed drives. Considering the low cost of this machine, the adoption of sensorless speed control is the more reasonable option for SPIM drives. This paper presents a proposal for sensorless variable speed SPIM drive based on direct rotor field orientation techniques. An observer based on two independent linear close-loop control systems provides the estimation of the rotor flux and speed from the measurements of the stator currents and voltages. These estimatives are used by close-loop systems for speed…
Dielectrophoretic trapping of DNA origami.
2008
In this thesis three-dimensional tube-shaped DNA-origamis were dielectrophoretically trapped within lithographically fabricated nanoelectrodes. The origamis had been premade while the electrodes were fabricated specifically for these experiments with two different gapsizes, 150 nm and 400 nm. The aim of the work was to capture individual nanotubes in the gap between the electrodes by utilizing the dielectrophoretic forces present in the structure when a solution containing the origamis was put onto the electrodes and a voltage was applied. It was observed during the experiments that the success of the dielectrophoretic trapping depended strongly on the trapping conditions. This caused the t…
A DSP-Based Resolver-To-Digital Converter for High-Performance Electrical Drive Applications
2016
This paper presents a low cost, simple, and highly accurate resolver-to-digital converter (RDC) for electrical drive applications based on an integrated software approach, thus allowing a significant reduction of hardware components count with significant improvements in terms of reliability, reduction of fault rate, and susceptibility to electromagnetic interference (EMI). Particular attention has been addressed to cost which is 25% off over conventional RDC. Simulations and experimental tests confirm the high quality of the proposed system.
A simulation model for electromagnetic transients in lightning protection systems
2002
This paper deals with the evaluation of electromagnetic transients in a lightning protection system (LPS). A field approach is used, based on the numerical solution of a modified version of the thin-wire electric field integral equation in the frequency domain. Time profiles of interesting electromagnetic quantities are computed by using a discrete fast Fourier transform algorithm. The model takes into account coupling effects among aerial parts and ground electrodes in order to correctly estimate the quantities which can determine electromagnetic hazard inside the LPS; transient touch and step voltages can be easily evaluated also taking into account the human body presence on the soil sur…
A Method for Reduction of Cogging Torque in PM Machines Using Stepped Magnets
2006
The paper presents a general approach to minimization of the cogging torque in electrical machines using surface-mounted magnets with discrete skew angle. Two types of pole shapes, namely monotonic skewing as well as herringbone-shaped magnets are proposed for the purpose of reducing the cogging torque. The elaborated algorithm is validated against the 3D finite element model as well as experimental data obtained from physical model of the motor. The presented cost-effective method leads to a great reduction of cogging torque with only slight decrease of overall electromagnetic torque.
Progress in the initial design activities for the European DEMO divertor: Subproject "Cassette"
2017
Abstract Since 2014 preconceptual design activities for European DEMO divertor have been conducted as an integrated, interdisciplinary R&D effort in the framework of EUROfusion Consortium. Consisting of two subproject areas, ‘Cassette’ and ‘Target’, this divertor project has the objective to deliver a holistic preconceptual design concept together with the key technological solutions to materialize the design. In this paper, a brief overview on the recent results from the subproject ‘Cassette’ is presented. In this subproject, the overall cassette system is engineered based on the load analysis and specification. The preliminary studies covered multi-physical analyses of neutronic, thermal,…
FDTD simulation for electromagnetic radiated emissions in 42 V vehicle electrical systems
2005
In this paper a full 3D approach, based on finite difference time domain method, is used to predict the electromagnetic radiated emissions from 42 V vehicle electrical loads. An experimental set-up has been arranged on purpose. A comparative analysis among measured and computed results is performed. The good agreement obtained among simulated and measured data enables to validate the numerical scheme. The proposed methodology contributes to predict electromagnetic emissions in the automotive environment since the design stage. Moreover, the proposed numerical tool can be used to define, for new vehicle electrical architectures, low cost test methods for electromagnetic compatibility and sui…
Absorption equipment for energy savings: A case study in Sicily
2013
Abstract This paper considers a feasibility study on the recovery of the reject heat available from an electric utility with two units operating with 120-MW gas turbines; these units have a heat recovery system that feeds the district heating pipeline of an industrial consortium. Thus, feeding the expeller of the absorption equipment installed in a cooling plant for foodstuff stocking represents an opportunity for the feasibility study. This plant operates at both 0 °C and −18 °C. The feasibility study covers two aspects: (1) the technical feasibility of a suitable absorption cooling plant that uses two separate pieces of absorption equipment working with the pair ammonia–water and (2) the …
<title>Modeling of eddy current sensors</title>
2001
In this paper two models of eddy current sensor have been presented. They are base don a one- and multi-turn coil model. The results of computer simulations present a relation of eddy current density on nonferromagnetic conducting materials versus some parameters viz: a coil radius, frequency of excitation current and conductivity of material.© (2001) COPYRIGHT SPIE--The International Society for Optical Engineering. Downloading of the abstract is permitted for personal use only.
Quasi-digital conversion for resistive devices: application in GMR-based IC current sensors
2013
Resistive devices, including sensors, are used in a huge range of applications within different scenarios. When a complete system is considered, a quasi-digital output is often recommendable. If the conversion is operated at device level, some problems such as noise disturbs, insertion losses and so on, can be reduced. In this work, we describe a resistance-tofrequency (R-f) converter with a suggested application in low current monitoring by means of GiantMagnetoResistance (GMR) sensors. Specific devices have been designed and microfabricated. The system has been tested by means of discrete components with a PCB. The complete microsystem monolithic integration in a standard CMOS technology …