Search results for "electronics"
showing 10 items of 4340 documents
Implementation of the ERI standard and Evaluation of Applications with several low-cost technologies
2008
The electronic registration and identification (ERI) systems allow carrying out a remote, secure and univocal identification of a vehicle through electronic devices. This paper presents the implementation of the ERI standard (ISO 24534 & 24535) in an API to develop applications. The implementation took into account the different components of the system to build the architecture of the identification system. Several applications have been developed in order to test this API with several low-cost technologies (Wifi, Bluetooth and RFID).
Optimal power flow based on glow worm-swarm optimization for three-phase islanded microgrids
2014
This paper presents an application of the Glowworm Swarm Optimization method (GSO) to solve the optimal power flow problem in three-phase islanded microgrids equipped with power electronics dc-ac inverter interfaced distributed generation units. In this system, the power injected by the distributed generation units and the droop control parameters are considered as variables to be adjusted by a superior level control. Two case studies with different optimized parameters have been carried out on a 6-bus test system. The obtained results showed the effectiveness of the proposed approach and overcomes the problem of OPF in islanded microgrids showing loads unbalance.
Minimum bond length and size effects in FRP–substrate bonded joints
2009
Abstract The load transfer mechanism between the fibre-reinforced polymer (FRP) materials and the substrate plays a crucial role in the overall response of retrofitted structural members. The FRP–support material interface can be studied by using pull tests in which a reinforcement plate is bonded to a prism and subjected to a tensile force. The experimental results obtained regard the assembly (FRP strip-support block), then a central problem is how to carry out the interface constitutive laws and the related parameters. The principal objective of the present paper is to contrive a procedure which, for a fixed interface constitutive law, permits to derive the interface mechanical parameter…
Integration of DC power source in micro-grid using VSI with PLL technique
2015
The looming energy crisis is becoming the greatest challenge to the world today. As a consequence of this there is an increasing attention for alternative renewable energy resources. In future, renewable energy sources will be integrated with energy storage and it will require a proper converter for integrating with the grid. In order to achieve this, various power electronics topologies have to be incorporated between the grid and the renewable source(s). This paper presents the simulation and experimental implementation of DC power source integration in micro-grid using single phase ‘Voltage Source Inverter’ (VSI) with ‘Phase Locked Loop’ (PLL) topology. Firstly the appropriateness of the…
Analyses of the OSU-MASLWR Experimental Test Facility
2012
Today, considering the sustainability of the nuclear technology in the energy mix policy of developing and developed countries, the international community starts the development of new advanced reactor designs. In this framework, Oregon State University (OSU) has constructed, a system level test facility to examine natural circulation phenomena of importance to multi-application small light water reactor (MASLWR) design, a small modular pressurized water reactor (PWR), relying on natural circulation during both steady-state and transient operation. The target of this paper is to give a review of the main characteristics of the experimental facility, to analyse the main phenomena characteri…
Low-Power Design of Delay Interpolating VCO
2008
In this paper, a design methodology for low-power MCML based delay interpolating VCOs is presented. The methodology allows a fast and accurate graphical evaluation of the optimum design. It utilizes two closed form expressions for the upper and lower oscillation frequencies of the VCO. An expression of the tuning range is also derived. The effectiveness of the proposed design methodology has been tested by simulating several VCOs in an IBM 0.13 mum CMOS technology.
Electrical-optical characterization of multijunction solar cells under 2000X concentration
2014
In the framework of the FAE "Fotovoltaico ad Alta Efficienza" ("High Efficiency Photovoltaic") Research Project (PO FESR Sicilia 2007/2013 4.1.1.1), we have performed electrical and optical characterizations of commercial InGaP/InGaAs/Ge triple-junction solar cells (1 cm2) mounted on a prototype HCPV module, installed in Palermo (Italy). This system uses a reflective optics based on rectangular off-axis parabolic mirror with aperture 45×45 cm2 leading to a geometrical concentration ratio of 2025. In this study, we report the I-V curve measured under incident power of about 700 W/m2 resulting in an electrical power at maximum point (PMP) of 41.4 W. We also investigated the optical properties…
A photovoltaic system suitable for the battery pack charging of an electrically power assisted velocipede
2012
The paper describes the designing, sizing, realization and setting up of a complete system suitable for the management of an electrically power assisted velocipede using a photovoltaic module for the charging of the batteries. In the work an overview on the sustainable mobility needs and on the commercial electrically power assisted velocipedes is presented and the "Ecolapa" prototype, set up in the SDELab laboratory of Palermo University, is precisely described underlining the designing, implementation and setting up phases of the photovoltaic charging system settled up on the velocipede. Moreover tests oriented on the setting up of the whole system and validation tests on the prototype ar…
Numerical Analysis of Medium Scale PV Plants and Their Power-Flow Control System With a Simple Three Phase Inverter
2012
This paper presents a mathematical analysis of a medium scale Photovoltaic (PV) power generation system connected to the distribution network and of its control system, in which the conversion stage is unique thanks to the absence of a boost chopper. Boost choppers are usually used as actuator for maximum power point tracking (MPPT). The conducted analysis leads to the conclusion that the used inverter presents two degrees of freedom that can be easily exploited in a control system in which the inverter simultaneously realizes the interconnection to the grid and at the same time realizes the MPPT control. The structure of the control system is then presented, discussed and then validated by…
Identification and robust control of DC/DC converter Hammerstein model
2008
Abstract—This paper deals with model-based robust control of dc/dc power electronic converters. The converter is described by means of a Hammerstein model consisting of the nonlinear static characteristics of the converter and a linear time-invariant (LTI) uncertainmodel whose parameters depend on the actual duty-cycle operating range. This suggests that the controller be designed using robust control techniques. In view of applying robust control, identification of the earlier LTI models is performed by means of simulation experiments, carried out on a converter switching model implemented onMATLAB/SIMULINK environment. Internal model control (IMC) structure is employed for the controller …