Search results for "engineering.material"

Epoxy composites filled with high surface area-carbon fillers

2013

Citation: J. Appl. Phys. 114, 164304 (2013); doi: 10.1063/1.4826529 (Received 24 July 2013; accepted 6 October 2013; published online 22 October 2013) A comprehensive analysis of electrical, electromagnetic (EM), mechanical, and thermal properties of epoxy resin composites filled with 0.25–2.0 wt. % of carbon additives characterized by high surface area, both nano-sized, like carbon nanotubes (CNTs) and carbon black (CBH), and micro-sized exfoliated graphite (EG), was performed. We found that the physical properties of both CNTs- and CBH-based epoxy resin composites increased all together with filler content and even more clearly for CBH than for CNTs. In the case of EG-based composites, go…

Coded excitation speeds up the detection of the fundamental flexural guided wave in coated tubes

2016

The fundamental flexural guided wave (FFGW) permits ultrasonic assessment of the wall thickness of solid waveguides, such as tubes or, e.g., long cortical bones. Recently, an optical non-contact method was proposed for ultrasound excitation and detection with the aim of facilitating the FFGW reception by suppressing the interfering modes from the soft coating. This technique suffers from low SNR and requires iterative physical scanning across the source-receiver distance for 2D-FFT analysis. This means that SNR improvement achieved by temporal averaging becomes time-consuming (several minutes) which reduces the applicability of the technique, especially in time-critical applications such as…

A Pearl Identification Challenge

2019

Alginate gel beads filled with halloysite nanotubes

2013

Abstract Novel hybrid gel beads with a well defined and controlled size formed by alginate biopolymer and halloysite (Hal) nanotubes were designed, prepared and characterized from the physico-chemical viewpoint. The thermogravimetry made it possible to determine the water content, the total as well as the local compositions of Hal into the gel beads. Dielectric spectroscopy evidenced that Hal reduced the fluctuation of ions. The SEM micrographs showed that the dried beads exhibit a rough surface, with pores in the micrometer range. In addition, the concentration of nanotubes was higher into the bead core at a higher overall loading. The performance of these materials was verified with the s…

Evolution of the structural and optical properties from cobalt cordierite glass to glass-ceramic based on spinel crystalline phase materials

2007

Co 2+ -containing cordierite stoichiometric glasses have been prepared by melting colloidal gel precursors. After controlled thermal processing in the range of temperatures between 900 and 1300 C different polycrystalline, almost single phase materials displaying l-, a-, and b-cordierite crystalline forms were synthesized. In addition, spinel glass-ceramic materials were also prepared from the base glasses. All these materials were characterized by X-ray powder diffraction and infrared spectroscopy. Room temperature (RT) absorption and emission spectra of Co 2+ – cordierites and – spinel-glass material have allowed determining the local environment of the Co 2+ in the crystalline structure …

Mechanism of crystallization of pyroxene-based glass-ceramic glazes

2004

Abstract The mechanism of crystallization of a powdered glass with composition in the pyroxene crystallization primary field within the CaO–MgO–Al 2 O 3 –SiO 2 quaternary system and containing some additives was studied. The crystallization sequence was compared with that from the same base glass without additives. After a short thermal anneal both powdered glasses showed phase separation. Further thermal treatment gave rise to the crystallization of pyroxene. Anorthite as secondary crystalline phase was also detected in the quaternary glass (without additives). The starting crystallization in the glass with additives took place in the outer surface of glass particles probably in the immisc…

Microstructural Evolution in Fast-Heated Cordierite-Based Glass-Ceramic Glazes for Ceramic Tile

2004

The crystallization mechanism of α-cordierite from a B 2 O 3 -and TiO 2 -containing glass submitted to fast heating in the cordierite primary phase field of the CaO-MgO-Al 2 O 3 -SiO 2 quaternary system was investigated. Addition of B 2 O 3 to a SiO 2 -rich glass suppressed the formation of μ-cordierite. This suppression facilitated densification by viscous flow before crystallization. Powder X-ray diffractometry, field-emission electron scanning microscopy, and energy-dispersive X-ray analysis revealed that α-cordierite nucleated directly from glass on the boundaries of original particles and was probably favored by TiO 2 , which acted as a nucleant. The growth kinetics of α-cordierite cry…

Effect of MgO/CaO ratio on the microstructure of cordierite-based glass-ceramic glazes for floor tiles

2005

Abstract The effect of the MgO/CaO ratio on the microstructure and microhardness of cordierite-based glass-ceramic glazes was studied. For this purpose glasses, with compositions in the cordierite primary phase field of the CaO–MgO–Al 2 O 3 –SiO 2 quaternary system and, with different MgO/CaO ratios, were prepared by melting. Glass powder pellets pressed under low pressure were fast heated at several temperatures simulating industrial floor-tile processing, and characterized by X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM) and energy dispersive X-ray emission spectroscopy (EDX). The studied glasses crystallized α-cordierite as the only crystalline phase…

Technical Program

2015

Evaluation of surface roughness of enamel after various bonding and clean-up procedures on enamel bonded with three different bonding agents : an in-…

2016

Background The purpose of this study was to analyze and compare the enamel surface roughness before bonding and after debonding, to find correlation between the adhesive remnant index and its effect on enamel surface roughness and to evaluate which clean-up method is most efficient to provide a smoother enamel surface. Material and methods 135 premolars were divided into 3 groups containing 45 premolars in each group. Group I was bonded by using moisture insensitive primer, Group II by using conventional orthodontic adhesive and Group III by using self-etching primer. Each group was divided into 3 sub-groups on the basis of type of clean-up method applied i,e scaling followed by polishing, …