Search results for "engineering.material"
showing 10 items of 2352 documents
In vitrouptake of lysozyme-loaded liposomes coated with chitosan biopolymer as model immunoadjuvants
2009
Chitosan binds to negatively charged soy lecithin liposomes by an electrostatic interaction driven by its cationic amino group. This interaction allows developing stable coated vesicles suitable as a targeted carrier and controlled release system for drugs and vaccines. In this work, we studied the effect of chitosan-coated liposomes on the uptake and antigen presentation of hen egg-white lysozyme (HEL) in Peyer's patches peritoneal macrophages isolated from mice. Chitosan-coated liposomes were characterized according to size, zeta potential, and antigen-loading and release properties. Results showed an increase in the positive net charge and size of the liposomes as the concentration of ch…
Preparation of Catalysts and Photocatalysts Used for Similar Processes
2019
Abstract This chapter reports the main techniques used to synthesize powders and films of heterogeneous catalysts and photocatalysts, often used for similar processes. Traditional preparation processes of bulky (photo)catalysts including precipitation, sol–gel technique, hydrothermal or solvothermal method, solid-state reactions, and flame syntheses were briefly described. The sonochemical method and microwave irradiation technique were also considered. The syntheses of supported catalysts by different techniques, including deposition–precipitation, impregnation, and wet coating technologies were also described. Moreover, a survey is reported of methods to deposit thin films of catalysts on…
Chromium oxide nanoparticles with controlled size prepared from hydrothermal chromium oxyhydroxide precursors
2017
Abstract This work reports the preparation of morphologically well-defined chromium oxide nanoparticles with controlled sizes of 20–30 nm. The synthetic procedure encompass two stages, the first one refers to the preparation of chromium oxyhydroxide nanoparticles by a hydrothermal approach of previously precipitated xerogels, followed by a thermal transformation of CrOOH nanoparticles to Cr2O3. The series of chromium oxyhydroxide particles sized over the range 15–50 nm were prepared through the control of the pH of precipitation of the xerogels and the water/xerogel ratio of the hydrothermal aging. Results showed the formation of non-aggregated oxyhydroxide nanoparticles with two different …
XPS and EELS investigations of chemical homogeneity in nanometer scaled Ti-ferrites obtained by soft chemistry
1999
Abstract Nanocrystalline Ti-ferrites with composition Fe 3− x Ti x O 4 with 0≤ x ≤1 are synthesized using the soft chemistry route. Heterogeneities in precipitate and annealed powders are investigated by a combination of XPS and EELS techniques. As-prepared powder consists in particles with spinel structure and grain size of about 15 nm. Due to high reactivity towards oxygen of nanoparticules, a significant amount of Fe 2+ cations oxidize during precipitation, so that precipitated powders present large deviation from oxygen-metal stoichiometry. Moreover precipitated particles are evidenced to exhibit a strong surface titanium enrichment and an iron richer core. Observation of such cation se…
Diamond Films as Support for Electrochemical Systems for Energy Conversion and Storage
2019
Many efforts have been dedicated to develop and study different catalysts supported materials for energy storage and conversion. Polymer electrolyte membranes (PEM) and capacitors have been topics of special interest for the scientific community, then, the research to find excellent catalyst-supports has constantly increased. The use of conductive diamond films has been proposed due to their mechanical and chemical stability properties. In this context, the application of BDD-catalyst surfaces for PEM fuel cells as well as the production of electrochemical capacitors using BDD materials have been summarized and discussed in this chapter.
Fast Polymeric Functionalization Approach for the Covalent Coating of MoS2 Layers
2021
We present the covalent coating of chemically exfoliated molybdenum disulfide (MoS2) based on the polymerization of functional acryl molecules. The method relies on the efficient diazonium anchoring reaction to provoke the in situ radical polymerization and covalent adhesion of functional coatings. In particular, we successfully implement hydrophobicity on the exfoliated MoS2 in a direct, fast, and quantitative synthetic approach. The covalent functionalization is proved by multiple techniques including X-ray photoelectron spectroscopy and TGA-MS. This approach represents a simple and general protocol to reach dense and homogeneous functional coatings on 2D materials.
Preparation of palladated porous nitrogen-doped carbon using halloysite as porogen: disclosing its utility as a hydrogenation catalyst
2020
AbstractIn this article, halloysite nanoclay (Hal) was used as porogen for the synthesis of nitrogen doped porous carbon material with high specific surface area and pore volume. To this purpose, polymerization of melamine and terephthalaldehyde (MT) was performed in the presence of amine-functionalized carbon coated Hal (Hal@Glu-2N) that was prepared from hydrothermal treatment of Hal and glucose. Then, the prepared nanocomposite was palladated and carbonized to afford Pd@Hal@C. To further improve the textural properties of the nanocomposite, and introduce more pores in its structure, Hal nanotubes were etched. The characterization of the resulting compound, Pd@C, and comparing it with Pd@…
Nano-composite thermochromic thin films and their application in Energy-efficient glazing
2010
A hybrid atmospheric pressure and aerosol-assisted chemical vapour deposition strategy is presented as a facile route for the production of vanadium dioxide nano-composite thin films. The effect of the inclusion of gold nanoparticles and the use of a surfactant molecule, tetraoctylammonium bromide, is discussed. The films were fully characterised using a wide variety of techniques, including scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and UV/vis/NIR spectroscopy. It is shown that micro-structural changes brought about by careful control of film growth conditions, and/or the use of surfactant, lead to an enhancement of thermochromic properties. Gold nano…
Electronic Properties of Thermal Oxides on Ti and Their Influence on Impedance and Photoelectrochemical Behavior of TiO2 Nanotubes
2017
Thermal oxidation of titaniumwas carried out at 350◦C, 450◦C, and 550◦C for 2 h or 12 h.X-rayDiffraction and Raman Spectroscopy suggest that the thermal oxides are scarcely crystallinewhen the annealing temperature is low, while both anatase and rutile are present for high annealing temperature and time. Photoelectrochemical measurements allowed estimation of a bandgap decreasing from 3.35 eV to 3.15 eV with increasing annealing temperature. The impedance spectra confirmed the formation of n-type semiconductors, with an impedance strongly decreasing on going from a reverse bias toward a forward bias regime. TiO2 nanotubes grown by anodizing Ti in NH4F and water containing ethylene glycol so…
Double Step Electrochemical Process for the Deposition of Superhydrophobic Coatings for Enhanced Corrosion Resistance
2021
Superhydrophobic surface on anodized AA5083 sample was obtained by an electrochemical process. Scanning Electron Microscopy and Fourier Transform Infrared Spectroscopy analyses revealed the hierarchical structure of the coating and the presence of manganese stearate. These features were crucial for the coating superhydrophobicity, demonstrated by a measured contact angle of ~ 163° and its self-cleaning ability. Electrochemical characterization in an aqueous solution mimicking seawater proved an enhanced corrosion resistance due to the superhydrophobic coating with respect to anodized AA5083 sample that also lasted after 20 immersion days in Cl- containing electrolyte.