Search results for "engineering.material"
showing 10 items of 2352 documents
Corrosion behaviour of galvanized steel studied by electrochemical microprobes applied on low-angle cross sections
2018
Abstract The combined use of the microcapillary cell (MEC) and scanning vibrating electrode technique (SVET) and low-angle cross sections was employed to elucidate the role of each coating region on the protection of the cut-edge corrosion of galvanized steels. Different compounds are involved in the blocking action of the corrosion products: Zincite (ZnO) on the steel substrate, hydrozincite (Zn5(OH)6(CO3)2) at the coating/steel interface, and Simonkolleite (Zn5(OH)8Cl2) and ZnO on the different coating regions in different proportions. The coating surface is also active at the initial stage and during long-term protection and thus, must be considered in experimental simulation of the cut-…
Study of the influence of dithizone as an eco-friendly corrosion inhibitor on the corrosion behaviour of AA7075 aluminium alloy in neutral chloride s…
2021
The effect of 1,5-diphenylthiocarbazone (dithizone) as an eco-friendly corrosion inhibitor for protection of AA7075 aluminium alloy in chloride containing aggressive environment was studied by means of weight-loss, electrochemical measurements and Raman spectroscopy. The results indicate that the addition of dithizone decreases significantly the corrosion rate of AA7075 alloy, with efficiency proportional to the inhibitor concentration. The polarization curves show that dithizone works as mixed-type inhibitor to slow down the anodic and cathodic reaction kinetic. The morphology revealed by scanning electron microscopy and the Raman spectroscopy analysis clearly shows that the inhibitor cont…
A Mechanical–Electrochemical Approach for the Determination of Precursor Sites for Pitting Corrosion at the Microscale
2006
International audience; The influence of metallurgical defects and residual surface stresses generated by polishing on the pitting susceptibility of duplex stainless steels was studied by combining macro- and microelectrochemical measurements with thermal-mechanical simulation and metallography tests. It has been shown that pits initiate in both phases at metallurgical point defects (such as oxide inclusions in the ferrite and dislocation lines in the austenite). By contrast, the surface stress state was the driving force for pit initiation along the austenite/ferrite interface. Experiments at the macroscale revealed that this process represents about 40% of the total number of pits observe…
Influence of Glass Additions on Illitic Clay Ceramics
2020
A mixture of an illitic clay and waste glass was prepared and studied during the sintering process. The illitic clay, from the Liepa deposit (Latvia), and green glass waste (GW) were disintegrated to obtain a homogeneous mixture. The addition of disintegrated GW (5&ndash
Comparison of the effect of different surface treatments on the bond strength of different cements with nickel chromium metal alloy: An in vitro study
2017
Background For success of any indirect metal restoration, a strong bond between cement and the intaglio surface of metal is imperative. The aim of this study is to evaluate and compare the effect of different surface treatment on the tensile and shear bond strength of different cements with nickel–chromium alloy. Material and Methods 120 premolars were sectioned horizontally parallel to the occlusal surface to expose the dentin. Wax patterns were fabricated for individual tooth followed by casting them in nickel chromium alloy. 60 samples were tested for tensile bond strength, and the remaining 60 for shear bond strength. The samples were divided into three groups (of 20 samples each) as pe…
Mix design and mechanical performance of geopolymer binder for sustainable construction and building materials
2017
Sustainability in construction is a major concern worldwide, due to the huge volume of materials and energy consumed by this sector. Associated supplementing industries (e.g. Portland cement production) constitute a significant source of CO2 emissions and global warming. Valorisation and reuse of industrial wastes and by-products make geopolymers a solid and sustainable via to be followed as a valid alternative to Portland cement. In this work the mix design of a green fly ash-based geopolymer is evaluated as an environmentally friendly construction material. In the pursuit of sustainability, wastes from a regional kraft pulp industry are exploited for the material processing. Furthermore, …
One-step electrodeposition of superhydrophobic coating on 316L stainless steel
2021
Superhydrophobic coatings were fabricated through a one-step electrochemical process onto the surface of 316L stainless steel samples. The presence of hierarchical structures at micro/nanoscale and manganese stearate into the coatings gave superhydrophobicity to the coating, with contact angle of ~160°, and self-cleaning ability. Corrosion resistance of 316L samples was also assessed also after the electrodeposition process through Electrochemical Impedance Spectra recorded in an aqueous solution mimicking seawater condition.
Ab initio modelling of silver adhesion on the corundum (0001) surface
2003
The Ag/a-Al2O3(0001) interface was simulated using ab initio slab calculations. We have studied silver adhesion on both Al- and Oterminated corundum substrates. The latter case may be considered as silver adhesion on a defective Al-terminated corundum surface with external aluminium vacancies. The dependence of the adhesion energy on the interfacial distance has been analyzed for the two favorable Ag adsorption positions and for two metal coverages (a 1/3 monolayer of the Ag(111) crystallographic plane and a full Ag(111) monolayer, 1 ML). The two different terminations (Al- and O-) give rise to qualitatively different results. In the former case, the small adhesion energies per Ag atom are …
Effects of powder concentration and type of resin on the performance of marble composite structures
2009
In this work, we will expose the behaviour of a composite structure reinforced with marble powder. The attention was focused on the effects produced on the physical and mechanical properties due to different kinds of matrix (epoxy and polyester resins) and filler amounts (60%, 70%, 80%). Rheological, static flexural and Izod impact tests have been carried out. An experiment designed was defined for the mechanical tests, in order to quantify the effects of both the resin and the marble percentage on the material properties, as well as to identify a possible correlation between these factors. Moreover, water absorption and stain resistance have been evaluated to study the surface properties o…