Search results for "epoxy resins"

E-beam curing of epoxy based blends in order to produce high performance composites

2007

In this work, blends of a difunctional epoxy monomer and a thermoplastic toughening agent are E-beam irradiated at two different dose rates and two different total absorbed doses. The influence of the processing conditions on the thermal properties and on the morphology of the obtained matrices has been investigated. In particular, it is shown how the increase of the dose rate causes an increase of the temperature during irradiation, thus inducing a simultaneous thermal and radiation curing. On the contrary, at low-dose rate the system mainly undergoes to radiation curing, thus making the cured material very sensible to a post-irradiation thermal treatment with a significant improvement of …

Accelerated ageing due to moisture absorption of thermally cured epoxy resin/polyethersulphone blends. Thermal, mechanical and morphological behaviour

2011

Abstract A model epoxy resin/anhydride system, modified with a polyethersulfone (PES) engineering thermoplastic toughening agent, has been studied under hydrothermal ageing in order to investigate the modification of the thermal, morphological and mechanical behaviour through dynamical mechanical thermal analysis, SEM microscopy and fracture toughness test respectively. Two different concentrations of the toughening agent were used in the blends and two ageing conditions have been considered, consisting of the immersion of the samples in distilled water at constant temperature of 70 °C for 1 week and for 1 month. Dynamical mechanical thermal analysis results on hydrothermally aged materials…

Mode I fracture toughness behavior of hydro-thermally aged carbon fibre reinforced DGEBA-HHPA-PES systems

2012

In this work the Mode I fracture toughness behavior of unidirectional CFRP laminates is investigated by means of Double Cantilever Beam (DCB) tests. The composite samples were manufactured by thermal curing after impregnation of a Carbon fabric with a DGEBA epoxy and anhydride HHPA curing agent. One resin batch was also mixed with a PES thermoplastic monomer to enhance the matrix toughness. Two lots of samples, toughened and un-toughened, were then left to soak in hot water to achieve various degrees of aging. The influence of matrix toughening and hydrothermal aging on the delamination behavior of the composite have then been assessed and correlated with characterization data from Dynamic …

Synthesis, structural, and thermal characterization of a new binuclear copper(II) chelate complex bearing an amine-hardener for epoxy resins

2016

A new di(μ-carbonato)bis[aqua(diethylenetriamine)copper(II)] hexahydrate complex, [{Cu(NH(C2H4NH2)2)(H2O)(μ-CO3)}2]⋅6H2O (1), was synthesized by direct interaction of malachite with diethylenetriamine (dien). The crystals of 1 were characterized by X-ray powder diffraction and IR spectra, as well as structurally characterized. Compound 1 consists of [{Cu(dien)(H2O)(μ-CO3)}2] discrete units whose CO32– anions play the role of bridging ligands combining two Cu(II) chelate cores into a centrosymmetric dimer. The elongated octahedral environment of Cu2+ consists of three nitrogens of dien and an oxygen from CO32– at the base of the bipyramid; the two apical positions of such polyhedron are occu…

Influence of Polymer Electrospun Nanofibers on Thermal Properties of Epoxy Resins

2019

Electrospinning of polymers has gained surging interest in the last decades due to its wide range of applications in different fields, such as sensors, electronic devices, separation systems, biomedical materials. Still there are only few reports on the use of these nanofibers as reinforcement in polymer composites. In this paper, solution electrospinning was employed to produce nanofibrous mats impregnating two epoxy resins to form “monolayer“ systems, with the aim to study the influence of the nanofibers on both the curing behaviour and the morphology of the resin systems. Three polymers were chosen for producing electrospun mats, a polysulfone (PSF), a polyamide Nylon 6,6 (Ny66) and a po…

EPOXY RESIN SYSTEMS CURABLE BY HIGH ENERGY RADIATION FOR ADVANCED COMPOSITES. STUDY OF THE EFFECTS OF PROCESS TEMPERATURE ON THERMAL PROPERTIES

2006

EPOXY RESIN VS BIOCERAMIC: SYSTEMATIC REVIEW WITH META-ANALYSIS

2021

Study of the curing of a DGEBA based system through structural investigation

2011

Influence of polymer electrospun nanofibers on thermal properties of epoxy resins

2019

Electrospinning of polymers has gained surging interest in the last decades due to its wide range of applications in different fields, such as sensors, electronic devices, separation systems, biomedical materials. Still there are only few reports on the use of these nanofibers as reinforcement in polymer composites. In this paper, solution electrospinning was employed to produce nanofibrous mats impregnating two epoxy resins to form “monolayer“systems, with the aim to study the influence of the nanofibers on both the curing behaviour and the morphology of the resin systems. Three polymers were chosen for producing electrospun mats, a polysulfone (PSF), a polyamide Nylon 6,6 (Ny66) and a pol…