Search results for "fille"
showing 10 items of 225 documents
Photo- and thermo- oxidative resistance of novel nanocomposites based on CNT-POSS hybrid nanofillers
2014
Effect of Sheep Wool Fibers on Thermal Insulation and Mechanical Properties of Cement-Based Composites
2019
The use of sheep wool as a filler of cement in order to produce mortar or plaster involves several advantages for environment and energy. Moreover, it is considered as a waste and, therefore, its use is characterized by low cost. The aim of this paper is to evaluate the influence of wool fibers on thermal conductivity and mechanical properties of cement. The samples were prepared using wool fibers, obtained from a breed of Sicilian sheep, with three different lengths (i.e., 1, 6, and 20 mm). Furthermore, in order to evaluate the influence of fiber content, the samples were prepared by varying the fiber weight fraction. The thermal conductivity of the samples was analyzed by using a heat flo…
Pumice powder as filler of self-compacting concrete
2015
Abstract An experimental study on the rheological and mechanical properties of self-compacting concrete with pumice powder used as filler additive is presented. Self-compacting concrete (SCC) shows its peculiar characteristics in the fresh state and many researches have been developed with reference to its rheological characteristics paying attention to the techniques of self-compacting properties assessment. One of the most important aspect in concrete mix-design is the type and the amount of fillers with respect to water and cement: this amount has great influence not only on self-compacting properties (fluidity, segregation, etc.), but also on the mechanical properties of the mixture. Vo…
Valorisation of industrial iron oxide waste to produce magnetic barium hexaferrite
2016
Barium M-type hexagonal ferrite (BaM, BaFe12O19) is an immensely important magnetic material, which we have successfully made from the simple valorisation of Fe-rich industrial waste from steel wire drawing, with addition of BaCO3 and heating in air to 1000 degrees C. The optimum ratio of Fe. Ba (producing 86 wt% BaM) was found to be 11: 1 (non-stoichiometric), and secondary phases of alpha-Fe2O3 (non-magnetic) and ZnFe2O4 (poorly antiferromagnetic) were always present. This material consisted of small submicron platelets. A hard magnetic ferrite was produced with Ms=48.6 A m(2) kg(-1) and H-c=211.5 kA m(-1). The highest density was achieved by sintering samples with Fe: Ba ratios of 11: 1 …
Contributions regarding increasing reliability of beer industry installations using weld cladding in ultrasonic field
2016
Paper presents a new technology for availability increasing of different installation parts used in beer industry - ultrasonic activation of metal deposition by welding. The dilution phenomenon is studied linked on its influence upon material technological and functional properties in the three distinct zones of resulted couple (filler material, influenced thermal zone, base material). Experimental results performed on unidirectional valve are presented regarding variation of chemical composition concentration and dilution variation in three zones influenced by ultrasonic wave.
Method of quantitative analysis of filler dispersion in composite systems with spherical inclusions
2011
In this work, a quantitative analysis method for the estimation of filler dispersion degree of filler particles in composite systems is presented and described. According to the procedure offered dispersion of filler particles of any form is associated with their area and the dispersion parameter D is defined as the probability to fall in a certain range of the particle area distribution. The method has been applied to both model and real systems characterized by different dispersion levels and various filler content. Final results highlight that for the case of better filler dispersion, the characteristic parameter, D, increases, since the quantity of filler particles having identical area…
Modeling of Melt Flow and Heat Transfer in Stationary Gas Tungsten Arc Welding with Vertical and Tilted Torches
2021
A 3D numerical simulation was conducted to study the transient development of temperature distribution in stationary gas tungsten arc welding with filler wire. Heat transfer to the filler wire and the workpiece was investigated with vertical (90°) and titled (70°) torches. Heat flux, current flux, and gas drag force were calculated from the steady-state simulation of the arc. The temperature in the filler wire was determined at three different time intervals: 0.12 s, 0.24 s, and 0.36 s. The filler wire was assumed not to deform during this short time, and was therefore simulated as solid. The temperature in the workpiece was calculated at the same intervals using heat flux, current flux, ga…
Sapropel as a Binder: Properties and Application Possibilities for Composite Materials
2015
Recent development trends largely look for possibilities of a wider use of natural materials and local resources. In this perspective, the use of organic rich lake sediment - sapropel - as a binding material in line with other environmentally friendly filling materials can be considered as a challenge. Sapropel itself is a valuable resource with multiple areas of application, for example, medicine, veterinary, agriculture, livestock farming, balneology, cosmetic applications, construction, and its application options have been widely studied in the 20th century in the Baltic countries, Ukraine and Russia. Birch wood fibre and sanding dust, hemp shives, 'Aerosil' are used as a filler and thr…
Degradation and stabilization of the polyolefins and of the filled-polyolefins
2009
Hialuronskābes filleru izraisītie blakusefekti
2018
Pamatojums: Ādā injicējamie hialuronskābes (HA) filleri ir minimāli invazīva sejas estētiska procedūra. HA ir ilgstošas iedarbības, minimāli imūngēni, un tos var sašķelt ar hialuronidāzi. Tomēr HA filleru injekcijas var izsaukt blakusefektus, sākot no nebūtiskiem līdz pat spēcīgiem. Mērķis: Šī darba mērķis ir noteikt sejas ādā injicējamo hialuronskābes filleru blakusefektu dažādību, biežumu un ilgumu. Materiāli un metodes: Šis šķērsgriezuma pētījums tika veikts izmantojot pacientu aptaujas lapas. Dati tika ievākti laika posmā no 2017.gada 6. novembra līdz 2018.gada 16. februārim klīnikā “Veselība un estētika”. Rezultāti: Kopumā tika analizēti 27 pacienti, kas atbilda kritērijiem, tostarp 26…