Search results for "filler"
showing 10 items of 106 documents
Halloysite Nanotubes Loaded with Calcium Hydroxide: Alkaline Fillers for the Deacidification of Waterlogged Archeological Woods
2018
A novel green protocol for the deacidifying consolidation of waterlogged archaeological woods through aqueous dispersions of polyethylene glycol (PEG) 1500 and halloysite nanotubes containing calcium hydroxide has been designed. First, we prepared functionalized halloysite nanotubes filled with Ca(OH)2 in their lumen. The controlled and sustained release of Ca(OH)2 from the halloysite lumen extended its neutralization action over time, allowing the development of a long-term deacidification of the wood samples. A preliminary thermomechanical characterization of clay/polymer nanocomposites allows us to determine the experimental conditions to maximize the consolidation efficiency of the wood…
Medicīna (Latvijas Universitātes Raksti; 812 sēj.)
2016
High performance composites containing perfluoropolyethers-functionalized carbon-based nanoparticles: Rheological behavior and wettability
2016
Abstract Ultra High Molecular Weight Polyethylene (UHMWPE) based composites filled with carbon nanotubes (CNTs) and carbon black (CB) modified by perfluoropolyethers (PFPE) have been formulated. All composites show a segregated morphology with nanofillers selectively localized at the polymer particle–particle interface. The composites rheological properties have been deeply investigated: the PFPE functionalities linked on CNTs facilitate the semi-3D nanofillers network formation in the composites that show a solid-like behaviour even at lower investigated filler contents, reaching the rheological percolation threshold at lower nanofiller content than bare CNTs filled composites. For composi…
The Effects of Nanoclay on the Mechanical Properties, Carvacrol Release and Degradation of a PLA/PBAT Blend
2020
The formulation of polymeric films endowed with the abilities of controlled release of antimicrobials and biodegradability is the latest trend of food packaging. Biodegradable polymer (Bio-Flex®
Photo- and thermo- oxidative resistance of novel nanocomposites based on CNT-POSS hybrid nanofillers
2014
Effect of Sheep Wool Fibers on Thermal Insulation and Mechanical Properties of Cement-Based Composites
2019
The use of sheep wool as a filler of cement in order to produce mortar or plaster involves several advantages for environment and energy. Moreover, it is considered as a waste and, therefore, its use is characterized by low cost. The aim of this paper is to evaluate the influence of wool fibers on thermal conductivity and mechanical properties of cement. The samples were prepared using wool fibers, obtained from a breed of Sicilian sheep, with three different lengths (i.e., 1, 6, and 20 mm). Furthermore, in order to evaluate the influence of fiber content, the samples were prepared by varying the fiber weight fraction. The thermal conductivity of the samples was analyzed by using a heat flo…
Pumice powder as filler of self-compacting concrete
2015
Abstract An experimental study on the rheological and mechanical properties of self-compacting concrete with pumice powder used as filler additive is presented. Self-compacting concrete (SCC) shows its peculiar characteristics in the fresh state and many researches have been developed with reference to its rheological characteristics paying attention to the techniques of self-compacting properties assessment. One of the most important aspect in concrete mix-design is the type and the amount of fillers with respect to water and cement: this amount has great influence not only on self-compacting properties (fluidity, segregation, etc.), but also on the mechanical properties of the mixture. Vo…
Valorisation of industrial iron oxide waste to produce magnetic barium hexaferrite
2016
Barium M-type hexagonal ferrite (BaM, BaFe12O19) is an immensely important magnetic material, which we have successfully made from the simple valorisation of Fe-rich industrial waste from steel wire drawing, with addition of BaCO3 and heating in air to 1000 degrees C. The optimum ratio of Fe. Ba (producing 86 wt% BaM) was found to be 11: 1 (non-stoichiometric), and secondary phases of alpha-Fe2O3 (non-magnetic) and ZnFe2O4 (poorly antiferromagnetic) were always present. This material consisted of small submicron platelets. A hard magnetic ferrite was produced with Ms=48.6 A m(2) kg(-1) and H-c=211.5 kA m(-1). The highest density was achieved by sintering samples with Fe: Ba ratios of 11: 1 …
Contributions regarding increasing reliability of beer industry installations using weld cladding in ultrasonic field
2016
Paper presents a new technology for availability increasing of different installation parts used in beer industry - ultrasonic activation of metal deposition by welding. The dilution phenomenon is studied linked on its influence upon material technological and functional properties in the three distinct zones of resulted couple (filler material, influenced thermal zone, base material). Experimental results performed on unidirectional valve are presented regarding variation of chemical composition concentration and dilution variation in three zones influenced by ultrasonic wave.
Method of quantitative analysis of filler dispersion in composite systems with spherical inclusions
2011
In this work, a quantitative analysis method for the estimation of filler dispersion degree of filler particles in composite systems is presented and described. According to the procedure offered dispersion of filler particles of any form is associated with their area and the dispersion parameter D is defined as the probability to fall in a certain range of the particle area distribution. The method has been applied to both model and real systems characterized by different dispersion levels and various filler content. Final results highlight that for the case of better filler dispersion, the characteristic parameter, D, increases, since the quantity of filler particles having identical area…