Search results for "firmware"
showing 10 items of 27 documents
Development of a 3D CZT Spectrometer System with Digital Readout for Hard X/Gamma-Ray Astronomy
2019
We report on the development and of a complete X/γ rays detection system (10-1000 keV) based on CZT spectrometers with spatial resolution in three dimensions (3D) and a digital electronics acquisition chain. The prototype is made by packing four linear modules, each composed of one 3D CZT sensors. Each sensors is realized using a single spectroscopic graded CZT crystal of about 20×20×5 mm3. An electrode structure consisting of 12 collecting anodes with a pitch of 1.6 mm and 3 drift strips between each pair of anodes for 48 strips (0.15 mm wide) on the anodic side was adopted. The cathode is made of 10 strips with a pitch of 2 mm and orthogonal to anode side strips. Since the reading of the …
Multiple register synchronization with a high-speed serial link using the Aurora protocol
2013
In this work, the development and characterization of a multiple synchronous registers interface communicating with a high-speed serial link and using the Aurora protocol is presented. A detailed description of the developing process and the characterization methods and hardware test benches are also included. This interface will implement the slow control busses of the digitizer cards for the second generation of electronics for the Advanced GAmma Tracking Array (AGATA).
Real time digital pulse processing for X-ray and gamma ray semiconductor detectors
2013
Abstract Digital pulse processing (DPP) systems, based on direct digitizing and processing of detector signals, have recently been favoured over analog electronics, ensuring higher flexibility, stability, lower dead time and better spectroscopic performance. In this work, we present the performance of a new real time DPP system for X-ray and gamma ray semiconductor detectors. The system is based on a commercial digitizer equipped with a custom DPP firmware, developed by our group, for on-line pulse height and shape analysis. X-ray and gamma ray spectra measurements with cadmium telluride (CdTe) and germanium (Ge) detectors highlight the excellent performance of the system both at low and hi…
Development of the Optical Multiplexer Board Prototype for Data Acquisition in the TileCal System
2006
This paper describes the development of the optical multiplexer board (OMB), also known as PreROD board, for the TileCal readout system in the ATLAS experiment. The aim of this board is to overcome the problems that may arise in the integrity of data due to radiation effects. The solution adopted has been to add redundancy to data transmission and so two optical fibers with the same data come out from the detector front end boards. The OMB has to decide in real time which fiber, eventually, carries data with no errors switching it to the output link connected to the read out driver (ROD) motherboard where data processing takes place. Besides, the board may be also used as a data injector fo…
Optical Link Card Design for the Phase II Upgrade of TileCal Experiment
2011
This paper presents the design of an optical link card developed in the frame of the R&D activities for the phase 2 upgrade of the TileCal experiment. This board, that is part of the evaluation of different technologies for the final choice in the next years, is designed as a mezzanine that can work independently or be plugged in the optical multiplexer board of the TileCal backend electronics. It includes two SNAP 12 optical connectors able to transmit and receive up to 75 Gb/s and one SFP optical connector for lower speeds and compatibility with existing hardware as the read out driver. All processing is done in a Stratix II GX field-programmable gate array (FPGA). Details are given on th…
Digital Front-End Electronics for the Neutron Detector NEDA
2015
19th Real Time Conference (RT) -- MAY 26-30, 2014 -- Nara, JAPAN
ISAdetect
2020
Static and dynamic binary analysis techniques are actively used to reverse engineer software's behavior and to detect its vulnerabilities, even when only the binary code is available for analysis. To avoid analysis errors due to misreading op-codes for a wrong CPU architecture, these analysis tools must precisely identify the Instruction Set Architecture (ISA) of the object code under analysis. The variety of CPU architectures that modern security and reverse engineering tools must support is ever increasing due to massive proliferation of IoT devices and the diversity of firmware and malware targeting those devices. Recent studies concluded that falsely identifying the binary code's ISA ca…
TileCal optical multiplexer board 9U prototype
2007
This paper presents the architecture and the status of the optical multiplexer board (OMB) for the ATLAS/LHC Tile hadronic calorimeter (TileCal). This board will analyze the front-end data CRC to prevent bit and burst errors produced by radiation. Besides, due to its position within the data acquisition chain it will be used to emulate front-end data for tests. The first two prototypes of the final OMB 9U version have been produced at CERN. Detailed design issues and manufacture features of these prototypes are described. These prototypes are being validated whereas some firmware developments are being implemented in the programmable devices of the board. Functional descriptions of the boar…
MAC design on real 802.11 devices: From exponential to Moderated Backoff
2016
In this paper we describe how a novel backoff mechanism called Moderated Backoff (MB), recently proposed as a standard extension for 802.11 networks, has been prototyped and experimentally validated on a commercial 802.11 card before being ratified. Indeed, for performance reasons, the time critical operations of MAC protocols, such as the backoff mechanism, are implemented into the card hardware/firmware and cannot be arbitrarily changed by third parties or by manufacturers only for experimental reasons. Our validation has been possible thanks to the availability of the so called Wireless MAC Processor (WMP), a prototype of a novel wireless card architecture in which MAC protocols can be p…
PQ Metrics Implementation on Low Cost Smart Metering Platforms. A Case Study Analysis
2018
The increasing interest on the quality of the energy supplied and generated in distribution networks is raising the need of distributed power quality (PQ) measurements. To allow such capabilities with cost effective metering solutions, this paper wants to investigate the feasibility of using smart meters, already installed for energy billing, also for power quality monitoring. To this aim, an electronic board (based on STCOMET metrology device), already used in many energy meters of different countries, has been selected as case study platform. The manufacturer firmware of this board was essentially aimed at implementing energy meter metrics and power line communications functionalities. In…