Search results for "git"
showing 10 items of 7116 documents
Unconventional Reducing Gases Monitoring in Everyday Places
2017
Abstract Air pollution, be it indoors or outdoors, is a major environmental health concern as it can lead to serious health effects, such as respiratory diseases, including asthma and lung cancer. Much progress has been made in Europe in improving outdoor air quality and limit values have been set for several pollutants. However, indoor air quality also requires attention because this is where we spend most of our time. Measurements at appropriate spatial and temporal scales are essential for understanding and monitoring heterogeneous environments with complex and highly variable emission sources, such as in urban areas. However, the costs and complexity of conventional air quality measurem…
A DSP-Based Resolver-To-Digital Converter for High-Performance Electrical Drive Applications
2016
This paper presents a low cost, simple, and highly accurate resolver-to-digital converter (RDC) for electrical drive applications based on an integrated software approach, thus allowing a significant reduction of hardware components count with significant improvements in terms of reliability, reduction of fault rate, and susceptibility to electromagnetic interference (EMI). Particular attention has been addressed to cost which is 25% off over conventional RDC. Simulations and experimental tests confirm the high quality of the proposed system.
BIM and Low-Cost Survey Techniques for Building Heritage Conservation
2017
The aim of this contribution is to illustrate a methodology for the protection and management of the building heritage, adding to the historical documentary investigations, a careful phase of survey and a conscious geometric and informational modelling of the pre-existence. The focus of this work was the Tower of Vietri sul Mare: a significant example of the architectural defense strategies adopted in Salerno in the 16th century. In fact, through the creation of digital models, it would be facilitated the management of the volumetric evolution that this tower has undergone over time, ensuring a greater accessibility and an easier understanding of the transformations it has suffered.
Welcome to MTI—A New Open Access Journal Dealing with Blue Sky Research and Future Trends in Multimodal Technologies and Interaction
2016
In this era of massive use of computers and other computational devices (e.g., low-cost wearable sensors, smartphones, other smart devices, etc.), the nature of digital data is becoming more complex and heterogeneous.
A microcontroller-based portable electrocardiograph recorder.
2004
We describe a low cost portable Holler design that can be implemented with off-the-shelf components. The recorder is battery powered and includes a graphical display and keyboard. The recorder is capable of acquiring up to 48 hours of continuous electrocardiogram data at a sample rate of up to 250 Hz.
Development of the control card for the digitizers of the second generation electronics of AGATA
2012
In this work, the features and development process of the novel control card for the digitizers of AGATA are presented. The board is part of the new hardware proposed for the electronic system of the experiment. In particular, the control card provides the sampling clock for the digitizers, contributes to the synchronization of the digital data and performs the slow control of its associated digitizer cards.
Event Reconstruction
2014
Event reconstruction is one of the most important step in digital forensic investigations. It allows investigators to have a clear view of the events that have occurred over time. Event reconstruction is a complex task which requires exploration of a large amount of events due to the pervasiveness of new technologies nowadays. Any evidence produced at the end of the investigative process must also meet the requirements of the courts, such as reproducibility, verifiability, validation, etc. After defining the most important concepts of event reconstruction, a survey of the challenges of this field and solutions proposed so far is given in this chapter. Irish Research Council Science Foundati…
Design And Characterization Of Automated Color Sensor System
2017
Abstract The paper presents a color sensor system that can process light reflected from a surface and produce a digital output representing the color of the surface. The end-user interface circuit requires only a 3-bit pseudo flash analog-to-digital converter (ADC) in place of the conventional/typical design comprising ADC, digital signal processor and memory. For scalability and compactness, the ADC was designed such that only two comparators were required regardless of the number of color/wavelength to be identified. The complete system design has been implemented in hardware (bread board) and fully characterized. The ADC achieved less than 0.1 LSB for both INL and DNL. The experimental r…
Quasi-digital conversion for resistive devices: application in GMR-based IC current sensors
2013
Resistive devices, including sensors, are used in a huge range of applications within different scenarios. When a complete system is considered, a quasi-digital output is often recommendable. If the conversion is operated at device level, some problems such as noise disturbs, insertion losses and so on, can be reduced. In this work, we describe a resistance-tofrequency (R-f) converter with a suggested application in low current monitoring by means of GiantMagnetoResistance (GMR) sensors. Specific devices have been designed and microfabricated. The system has been tested by means of discrete components with a PCB. The complete microsystem monolithic integration in a standard CMOS technology …
Filling defects in a ceramics forming process
1997
Publisher Summary This paper presents a simple semi-heuristic method to predict mold filling defects in a porcelain forming process. It involves both a mechanical modelling of this process as a squeezing flow, and a postprocessing calculus that unable a defects prediction as soon as the shape and the size of artistic reliefs are known. This shape analysis is carried out with a multi resolution wavelet analysis. The chapter models the filling stage and to propose a criterium to avoid any filling defect that could waste the quality of the drawings. It illustrates a simplified modelling of the process during which the “turning” stage is approximated by the deformation under pressure of a Norto…