Search results for "harmonic analysis"
showing 10 items of 75 documents
A novel method for harmonic mitigation for single-phase five-level cascaded H-Bridge inverter
2018
The efficiency of a system is a very important parameter for high power electrical drives applications. Moreover, the efficiency of power converters plays a fundamental role. Aim of this work, is to propose a novel selective harmonic mitigation method without solving non-linear equations. Through a very simple approach, the polynomial equations which drive the control angles have been detected for a single-phase five-level cascaded H-Bridge inverter. The obtained polynomial equations can be easily implemented in a digital system to real-time operation. The paper also presents the simulation analysis and experimental validation.
Enhanced Modelling for Extended Performance Analysis of Interior Permanent Magnet Synchronous Machine Drive fed with Cascaded H-Bridges Multilevel In…
2021
This paper presents a comparative simulation analysis of an Interior Permanent Magnet Synchronous Machine (IPMSM) performance once fed by a traditional three-phase two-level inverter and then using a three-phase five-level Cascaded H-Bridges Multilevel Inverter (CHBMI). For this purpose, an enhanced mathematical model of the IPMSM, that take into account simultaneously saturation, cross-coupling, spatial harmonics and iron loss effects, has been employed. Furthermore, two different PWM modulation strategies have been considered. The study was conducted for several working conditions, evaluating the impact of CHBMI adoption on the IPMSM performance in terms of improved efficiency and torque …
The use of slightly asymmetrical windings for rotating electrical machines
2018
Historically, asymmetrical windings in electrical machines have been rarely used and only for specified needs, because the adoption of symmetrical configurations has always been considered the only solution during the design stage of electrical machines. The aim of this work is to demonstrate with several examples that the use of slightly asymmetrical windings can be a reasonable choice and, in certain cases, a favorable option during the machine design stage, allowing the possibility of selecting a wider range of slot/pole number combinations, without affecting the performances of the machines. More in detail, an interior permanent magnet synchronous machine equipped with a symmetrical 3-p…
A Novel Symmetrical Boost Modulation Method for qZS-based CHB Inverters
2020
Quasi-Z-source cascaded H-bridge (qZS-CHB) inverters are arising as an innovation in the field of the electrical conversion for PV applications. This type of converters inherit the advantages of multilevel inverters and single-stage configuration. In this context, this paper proposes a novel symmetrical boost modulation strategy for qZS CHB multilevel inverters to increase the performance in terms of voltage stresses and power quality. The novelty lies in the adoption of a different concept to generate the shoot-through states compared to the traditional methods. Simulation analysis in a grid connected application to evaluate the benefits of this boost method is performed in the MATLAB/PLEC…
Selective Harmonic Elimination in a 5-Level Single Phase Converter with FPGA Based Controller
2018
Multilevel converters are becoming popular in high-power applications such as motor drives, renewable energy systems and distribution systems. Among all modulation techniques, selective harmonic elimination methods offer high quality voltage waveforms with operations at low switching frequency, hence, they are especially suitable for high-power applications. In this paper, a new analytical expression for the SHE problem formulated for a five-level converter is introduced, which is able to calculate the exact value of the switching angles. After a mathematical description of the proposed approach, this manuscript reports simulation and experimental results and analysis showing achievable res…
Measurement of Simplified Single- And Three-Phase Parameters for Harmonic Emission Assessment Based on IEEE 1459-2010
2021
This article investigates the feasibility of using a simplified approach, based on the measurement of power ratio parameters, for harmonic emissions assessment at the point of common coupling (PCC). The proposed approach comes from the common concept of power factor correction and the definitions of the IEEE Std. 1459-2010, where line utilization and harmonic pollution levels are evaluated by means of ratios between the power quantities of the apparent power decomposition. In addition to the IEEE Std. 1459–2010 indicators, in this article, the behavior is studied of additional parameters that are conceptually similar to those defined by the IEEE Std. 1459-2010. The suitability of such param…
A Cogging Torque Minimization Procedure for Interior Permanent Magnet Synchronous Motors Based on a Progressive Modification of the Rotor Lamination …
2022
This article describes a simple cogging torque minimization procedure for interior permanent magnet synchronous machines (IPMSMs), consisting of a progressive modification of the rotor lamination geometry. This procedure can be generalized for the main topologies of PMSM, independently of the number of stator slots or the location of the permanent magnets. For this purpose, a basic IPMSM structure is analyzed by means of the FEM (finite element method) approach, and then, several other IPMSM geometries, obtained by adequately modifying the rotor lamination geometry of the basic IPMSM model without changing its stator configuration, are proposed and discussed. The trends of the cogging torqu…
CZT-Based Harmonic Analysis in Smart Grid Using Low-Cost Electronic Measurement Boards
2023
This paper validates the use of a harmonic analysis algorithm on a microcontroller to perform measurements of non-stationary signals in the context of smart grids. The increasing presence of electronic devices such as inverters of distributed generators (DG), power converters of charging stations for electric vehicles, etc. can drain non-stationary currents during their operation. A classical fast Fourier transform (FFT) algorithm may not have sufficient spectral resolution for the evaluation of harmonics and inter-harmonics. Thus, in this paper, the implementation of a chirp-Z transform (CZT) algorithm is suggested, which has a spectral resolution independent from the observation window. T…
Modelling of EM glass convection
2008
PurposeTo develop the mathematical model, which allows predicting the temperature and flow distribution of an opaque glass melt with the temperature‐dependent properties in case it is generated by electromagnetic and thermal convection. Analysis has been done for geometry of the model crucible with the immersed rod electrodes. Numerical analysis is used as a tool for finding out the parameters of the system, which allow getting desiderated homogeneity of temperature field by EM action.Design/methodology/approachANSYS CFX software is implemented for coupling of EM, thermal and HD processes in the modelled system. Usability of non‐inductive approximation is shown using a full harmonic analysi…
A New Software Tool for Design, Optimization, and Complete Analysis of Rotating Electrical Machines Windings
2015
In this paper, a new software tool developed by the authors for ac winding design, optimization, and complete analysis is presented. In particular, this software can be used as a valid aid in design and analysis for a wide variety of motor and generator windings with generic number of phases (including the case of those machines in which some slots are left empty), pole pairs, slot number, and so on. The calculation of winding factors and the evaluation of their harmonic distribution is also accomplished. The software is implemented in the MATLAB programming environment. By means of some examples, covering the most relevant winding types, the capabilities of this software will be shown. In …