Search results for "high temperature"

Study of a chromia-forming alloy behavior as interconnect material for High Temperature Vapor Electrolysis

2011

In High Temperature Vapor Electrolysis (HTVE) system, the materials chosen for the interconnectors should have a good corrosion behaviour in air and in H2-H2O mixtures at 800°C, and keep a high electronic conductivity over long durations as well. In this context, the first goal of this study was to evaluate a commercial ferritic alloy (the K41X alloy) as interconnect for HTVE application. Oxidation tests in furnace and in microbalance have therefore been carried out in order to determine oxidation kinetics. Meanwhile, the Area Specific Resistance (ASR) was evaluated by Contact Resistance measurements performed at 800°C. The second objective was to improve our comprehension of chromia-formin…

Structural investigation of crystallized Ge-Ga-Se chalcogenide glasses

2018

H. Klym thanks to the Ministry of Education and Science of Ukraine for support and Dr. P. Demchenko for the assistance in XRD experiments.

NaCl induced corrosion of Ti-6Al-4V alloy at high temperature

2016

International audience; This paper presents a study on the Ti-6Al-4V behaviour in presence of NaCl deposit under dry and moistair environments at 560◦C. The results evidence a detrimental effect of the NaCl deposit with a synergisticeffect in presence of moist air environment. Treatments under dry and moist air with NaCl deposit for600 h, lead respectively to weight gains per unit area 5 and 15 times higher than observed under classicoxidation in dry air. Enhancement of the corrosion phenomenon is attributed to the presence of gaseousmetal chlorides, leading to the establishment of an active corrosion process.

Beta-forging of Ti6Al4V titanium alloy powders consolidated by HIP: Plastic flow and strain-rate relation

2014

Ti6Al4V is probably the best known and studied titanium alloy, not only for aerospace applications. Nevertheless the deformation behavior still represents a challenge if any modification in the deformation process is required or introduced. This work deals with deformation behavior description of Ti6Al4V HIPped powders during high temperature deformation tests carried on in the Beta-region. Laboratory compression and tensile tests have been coupled with relaxation tests in order to achieve robust data about strain rate sensibility m-coefficient and activation energy Q. These results have been fitted for the assessment of a more general exponential deformation law. The final result is a “Dor…

Coating impact and radiation effects on optical frequency domain Reflectometry fiber-based temperature sensors

2015

International audience; Temperature response of radiation-tolerant OFDR-based sensors is here investigated, with particular attention on the impact of coating on OFS. By performing consecutive thermal treatments we developed a controlled system to evaluate the performances of our distributed temperature sensor and to estimate the radiation impact. We show an important evolution of the temperature coefficient measurements with thermal treatments for non-irradiated fiber and that the amplitude of this change decreases increasing radiation dose. As final results, we demonstrate that sensor performances are improved if we performed a pre-thermal treatment on the fiber-based system permitting to…

Physico-chemical characterization of passive films on 316L stainless steel grown in high temperature water

2014

Photoelectrochemical Characterization of Oxide Layers on 316L Stainless Steel Grown in High temperature Water

2014

Photoelectrochemical and XPS Characterization of Passive films Grown on 316L Stainless Steel in High Temperature Water

2015

One of the major materials challenge for continued safe, reliable and cost-effective utilization of watercooled nuclear reactors for electricity production is development of improved understanding of the synergistic fundamental mechanisms responsible for corrosion and stress corrosion cracking degradation of austenitic steels and nickel base alloys

Surface-barrier effects in the microwave second-harmonic response of superconductors in the mixed state

2005

We report on transient effects in the microwave second-harmonic response of different type of superconductors in the mixed state. The samples have contemporarily been exposed to a dc magnetic field, varying with a constant rate of 60 Oe/s, and a pulsed microwave magnetic field. The time evolution of the signal radiated at the second-harmonic frequency of the driving field has been measured for about 500 s from the instant in which the dc-field sweep has been stopped, with sampling time of ∼0.3 s. We show that the second-harmonic signal exhibits two relaxation regimes; an initial exponential decay, which endures roughly 10 s, and a logarithmic decay in the time scale of minutes. Evidence is …

Microwave second-harmonic response of ceramic MgB2 samples

2005

Nonlinear microwave response of different ceramic MgB2 samples has been investigated by the technique of second-harmonic emission. The second-harmonic signal has been investigated as a function of temperature, DC magnetic field and input microwave power. The attention has mainly been devoted to the response at low magnetic fields, where nonlinear processes arising from motion of Abrikosov fluxons are ineffective. The results show that different mechanisms are responsible for the nonlinear response in the different ranges of temperature. At low temperatures, the nonlinear response is due to processes involving weak links. At temperatures close to Tc, a further contribution to the harmonic em…