Search results for "ibers"

Salt-fog spray aging of jute-basalt reinforced hybrid structures. Flexural and low velocity impact response

2017

Abstract In this work, a study on the aging resistance of jute and jute-basalt interply hybrid laminates exposed to salt-fog is presented with the aim to investigate the possibility to enhance the durability of natural fiber reinforced composites for marine application by a ply-substitution approach. In particular, jute and basalt/jute reinforced composite plates were manufactured by vacuum assisted resin infusion in two different staking sequences (i.e., intercalated and sandwich-like basalt-jute) and aged under salt fog conditions. The effects of the accelerated aging at increasing times on the mechanical response of laminates were assessed in both quasi static (three point bending) and d…

Influence of sol counter-ions on the visible light induced photocatalytic behaviour of TiO2 nanoparticles

2014

Titanium dioxide (TiO2) nanoparticles are attracting increasing interest because of their superior photocatalytic and antibacterial properties. Here, aqueous titanium oxy-hydroxide sols were made, using a green synthesis method, from the controlled hydrolysis/peptisation of titanium isopropoxide. Three different mineral acids were used to peptise the sol (HNO3, HBr and HCl), and provide counter-ions. The influence of nitrate or halide sol counter-ions on size distributions of the starting sols were measured via photon correlation spectroscopy (PCS). Semi-quantitative phase composition analysis (QPA), on the gels thermally treated at 450 and 600 degrees C, was carried out via Rietveld refine…

Dynamic control of the operation regimes of a mode-locked fiber laser based on intracavity polarizing fibers: experimental and theoretical validation.

2012

[EN] An intracavity polarizing fiber is proposed to control the emission regime of a passively mode-locked fiber laser. Stable operation in self-starting high and low dispersion soliton mode-locking and 100 GHz multiwavelength regimes is demonstrated through numerical simulations and experimental validation. Mode-locking stability is ensured by a saturable absorber in the ring cavity. The effective selection of operation regime is dynamically carried out by controlling the intracavity polarization state.

Implementation of eco-sustainable biocomposite materials reinforced by optimized agave fibers

2018

Abstract Although several works have recently been published in literature about biocomposites, i.e. about composites with polymeric matrix reinforced by natural fibers, only a few articles have been devoted to the implementation of high performance biocomposites for structural and semi-structural applications. The present study aims to give a contribution by considering biocomposites obtained by using an eco-friendly partially bio-based epoxy (green epoxy) and sisal (agave sisalana fibers) obtained by a proper optimization process. Through a systematic experimental analysis, three different types of biocomposites obtained with a suitable manufacturing process, such as random short fiber bi…

Influence of pulp bleaching and compatibilizer selection on performance of pulp fiber reinforced PLA biocomposites

2019

Behaviour in compression of lightweight fiber reinforced concrete confined with transverse steel reinforcement

2004

Abstract The compressive behavior of lightweight fiber reinforced concrete confined with transverse reinforcement consisting of steel stirrups or spirals was analyzed. Pumice stone and expanded clay aggregates were utilized to decrease the weight of the composite; hooked steel fibers were also added. The investigation was carried out by testing cylindrical and prismatic specimens of different sizes in compression using an open-loop displacement control machine, recording the full load–deformation curves. The influence of the dimensions and shape on the bearing capacity and on the ductility of the specimens confined with transverse steel reinforcements was analyzed. The results show the poss…

Q -switched and modelocked all-fiber lasers based on advanced acousto-optic devices

2011

The interest in all-fiber lasers is stimulated by the inherent advantages they have over bulk lasers in aspects such as heat dissipation and robustness. The performance of Q-switched and modelocked fiber lasers can benefit enormously from the development of all-fiber configurations. A fiber laser with strictly all-fiber components can fulfil the requirements of mechanical stability, low maintenance, enhanced power efficiency, simplified assembly process, and low cost. In this framework, recent developments infiber acousto-optic devices are reviewed that have demonstrated new possibilities for actively Q-switched distributed feedback fiber lasers, modelocking lasers and doubly active Q-switc…

Steel fiber-reinforced concrete corbels:experimental behavior and shear strength prediction

2007

Corbels are structural members often used in reinforced concrete structures to transfer vertical and horizontal forces to principal members. This paper presents experimental research regarding the flexural behavior of corbels in plain and fibrous concrete and in the presence of steel bars. The study considers the influence of the type of concrete grade (normal- and high-strength concretes), of the fiber percentage and of the arrangement and percentage of the steel bars on the flexural behavior of the corbels. The results in terms of load-deflection curves and crack patterns show the effectiveness in using fibrous reinforced concrete corbels as well as in the presence of stirrups ensuring ad…

Microfluidic production of hyaluronic acid derivative microfibers to control drug release

2016

"Available online 4 July 2016"

Polycaprolactone/gelatin-based scaffolds with tailored performance: in vitro and in vivo validation

2019

Abstract Nanofibrous scaffolds composed of polycaprolactone (PCL) and gelatin (Ge) were obtained through a hydrolytic assisted electrospinning process. The PCL-to-Ge proportion (100/0 to 20/80), as well as the dissolution time (24, 48, 72, 96, 120 h) into a 1:1 formic/acetic acid solvent before electrospinning were modified to obtain the different samples. A strong influence of these factors on the physicochemical properties of the scaffolds was observed. Higher Ge percentage reduced crystallinity, allowed a uniform morphology and increased water contact angle. The increase in the dissolution time considerably reduced the molar mass and, subsequently, fibre diameter and crystallinity were a…